Re: [PATCH v7 1/4] mfd: bd71837: mfd driver for ROHM BD71837 PMIC

From: Enric Balletbo Serra
Date: Tue Jun 26 2018 - 05:06:57 EST

Next message: Paolo Bonzini: "Re: [PATCH v2] kvm: x86: mmu: Add cast to negated bitmasks in update_permission_bitmask()"
Previous message: Peter Zijlstra: "Re: [RFC PATCH 06/16] x86/split_lock: Save #AC setting for split lock in firmware in boot time and restore the setting in reboot"
Next in thread: Matti Vaittinen: "Re: [PATCH v7 1/4] mfd: bd71837: mfd driver for ROHM BD71837 PMIC"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Hi Matti,

Thanks for the patch, a few comments below, some are feedback I
received when I sent some patches to this subsystem.

Missatge de Matti Vaittinen <matti.vaittinen@xxxxxxxxxxxxxxxxx> del
dia dt., 19 de juny 2018 a les 12:57:
>
> ROHM BD71837 PMIC MFD driver providing interrupts and support
> for two subsystems:
> - clk
> - Regulators
>
> Signed-off-by: Matti Vaittinen <matti.vaittinen@xxxxxxxxxxxxxxxxx>
> ---
> drivers/mfd/Kconfig | 13 ++
> drivers/mfd/Makefile | 1 +
> drivers/mfd/bd71837.c | 221 ++++++++++++++++++++++++++
> include/linux/mfd/bd71837.h | 367 ++++++++++++++++++++++++++++++++++++++++++++
> 4 files changed, 602 insertions(+)
> create mode 100644 drivers/mfd/bd71837.c
> create mode 100644 include/linux/mfd/bd71837.h
>
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index b860eb5aa194..7aa05fc9ed8e 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -1787,6 +1787,19 @@ config MFD_STW481X
> in various ST Microelectronics and ST-Ericsson embedded
> Nomadik series.
>
> +config MFD_BD71837
> + bool "BD71837 Power Management chip"

I know that some drivers need to be built-in, is this really a
requirement for this driver? Or should work as a module too.

> + depends on I2C=y
> + depends on OF
> + select REGMAP_I2C
> + select REGMAP_IRQ
> + select MFD_CORE
> + help
> + Select this option to get support for the ROHM BD71837
> + Power Management chips. BD71837 is designed to power processors like
> + NXP i.MX8. It contains 8 BUCK outputs and 7 LDOs, voltage monitoring
> + and emergency shut down as well as 32,768KHz clock output.
> +
> config MFD_STM32_LPTIMER
> tristate "Support for STM32 Low-Power Timer"
> depends on (ARCH_STM32 && OF) || COMPILE_TEST
> diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
> index e9fd20dba18d..09dc9eb3782c 100644
> --- a/drivers/mfd/Makefile
> +++ b/drivers/mfd/Makefile
> @@ -227,4 +227,5 @@ obj-$(CONFIG_MFD_STM32_TIMERS) += stm32-timers.o
> obj-$(CONFIG_MFD_MXS_LRADC) += mxs-lradc.o
> obj-$(CONFIG_MFD_SC27XX_PMIC) += sprd-sc27xx-spi.o
> obj-$(CONFIG_RAVE_SP_CORE) += rave-sp.o
> +obj-$(CONFIG_MFD_BD71837) += bd71837.o
>
> diff --git a/drivers/mfd/bd71837.c b/drivers/mfd/bd71837.c
> new file mode 100644
> index 000000000000..0f0361d6cad6
> --- /dev/null
> +++ b/drivers/mfd/bd71837.c
> @@ -0,0 +1,221 @@
> +// SPDX-License-Identifier: GPL-2.0

There is a mismatch between what SPDX says and MODULE_LICENSE says.

GPL-2.0 = GPL v2 only
MODULE_LICENSE(GPL) = GPL v2 or later.

You'd like to change the SPDX identifier to GPL-2.0-or-later or set
module license to "GPL v2".

> +// Copyright (C) 2018 ROHM Semiconductors
> +// bd71837.c -- ROHM BD71837MWV mfd driver
> +//
> +// Datasheet available from
> +// https://www.rohm.com/datasheet/BD71837MWV/bd71837mwv-e
> +
> +#include <linux/module.h>
> +#include <linux/moduleparam.h>
This include is not required.

> +#include <linux/init.h>
> +#include <linux/slab.h>
> +#include <linux/i2c.h>
> +#include <linux/interrupt.h>
> +#include <linux/irq.h>
ditto

> +#include <linux/irqdomain.h>
ditto

> +#include <linux/gpio.h>
ditto

> +#include <linux/regmap.h>
> +#include <linux/of_device.h>
> +#include <linux/of_gpio.h>
ditto
> +#include <linux/mfd/core.h>
> +#include <linux/mfd/bd71837.h>
> +

Please review the needed includes.

> +static const struct resource irqs[] = {
> + {
> + .start = BD71837_INT_PWRBTN,
> + .end = BD71837_INT_PWRBTN,
> + .flags = IORESOURCE_IRQ,
> + .name = "pwr-btn",
> + }, {
> + .start = BD71837_INT_PWRBTN_L,
> + .end = BD71837_INT_PWRBTN_L,
> + .flags = IORESOURCE_IRQ,
> + .name = "pwr-btn-l",
> + }, {
> + .start = BD71837_INT_PWRBTN_S,
> + .end = BD71837_INT_PWRBTN_S,
> + .flags = IORESOURCE_IRQ,
> + .name = "pwr-btn-s",
> + },

nit: no comma at the end

> +};
> +
> +/* bd71837 multi function cells */
> +static struct mfd_cell bd71837_mfd_cells[] = {
> + {
> + .name = "bd71837-clk",
> + }, {
> + .name = "bd718xx-pwrkey",
> + .resources = &irqs[0],
> + .num_resources = ARRAY_SIZE(irqs),
> + }, {
> + .name = "bd71837-pmic",
> + },
nit: no comma at the end

> +};
> +
> +static const struct regmap_irq bd71837_irqs[] = {
> + REGMAP_IRQ_REG(BD71837_INT_SWRST, 0, BD71837_INT_SWRST_MASK),
> + REGMAP_IRQ_REG(BD71837_INT_PWRBTN_S, 0, BD71837_INT_PWRBTN_S_MASK),
> + REGMAP_IRQ_REG(BD71837_INT_PWRBTN_L, 0, BD71837_INT_PWRBTN_L_MASK),
> + REGMAP_IRQ_REG(BD71837_INT_PWRBTN, 0, BD71837_INT_PWRBTN_MASK),
> + REGMAP_IRQ_REG(BD71837_INT_WDOG, 0, BD71837_INT_WDOG_MASK),
> + REGMAP_IRQ_REG(BD71837_INT_ON_REQ, 0, BD71837_INT_ON_REQ_MASK),
> + REGMAP_IRQ_REG(BD71837_INT_STBY_REQ, 0, BD71837_INT_STBY_REQ_MASK),
> +};
> +
> +static struct regmap_irq_chip bd71837_irq_chip = {
> + .name = "bd71837-irq",
> + .irqs = bd71837_irqs,
> + .num_irqs = ARRAY_SIZE(bd71837_irqs),
> + .num_regs = 1,
> + .irq_reg_stride = 1,
> + .status_base = BD71837_REG_IRQ,
> + .mask_base = BD71837_REG_MIRQ,
> + .ack_base = BD71837_REG_IRQ,
> + .init_ack_masked = true,
> + .mask_invert = false,
> +};
> +
> +static int bd71837_irq_exit(struct bd71837 *bd71837)
> +{
> + if (bd71837->chip_irq > 0)
> + regmap_del_irq_chip(bd71837->chip_irq, bd71837->irq_data);
> + return 0;
> +}
> +
> +static const struct regmap_range pmic_status_range = {
> + .range_min = BD71837_REG_IRQ,
> + .range_max = BD71837_REG_POW_STATE,
> +};
> +
> +static const struct regmap_access_table volatile_regs = {
> + .yes_ranges = &pmic_status_range,
> + .n_yes_ranges = 1,
> +};
> +
> +static const struct regmap_config bd71837_regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 8,
> + .volatile_table = &volatile_regs,
> + .max_register = BD71837_MAX_REGISTER - 1,
> + .cache_type = REGCACHE_RBTREE,
> +};
> +
> +#ifdef CONFIG_OF

The driver is DT-only and depends on OF so you don't need to protect this.

> +static const struct of_device_id bd71837_of_match[] = {
> + { .compatible = "rohm,bd71837", .data = (void *)0},
> + { },

nit: { /* sentinel */ }

> +};
> +MODULE_DEVICE_TABLE(of, bd71837_of_match);
> +#endif //CONFIG_OF
> +
> +static int bd71837_i2c_probe(struct i2c_client *i2c,
> + const struct i2c_device_id *id)
> +{
> + struct bd71837 *bd71837;
> + struct bd71837_board *board_info;
> + int ret = -EINVAL;
> +
> + board_info = dev_get_platdata(&i2c->dev);
> +
> + if (!board_info) {
> + board_info = devm_kzalloc(&i2c->dev, sizeof(*board_info),
> + GFP_KERNEL);
> + if (!board_info) {
> + ret = -ENOMEM;
> + goto err_out;
> + } else if (i2c->irq) {
> + board_info->gpio_intr = i2c->irq;
> + } else {
> + ret = -ENOENT;
> + goto err_out;
> + }
> + }
> +
> + if (!board_info)
> + goto err_out;
> +
> + bd71837 = devm_kzalloc(&i2c->dev, sizeof(struct bd71837), GFP_KERNEL);
> + if (bd71837 == NULL)
> + return -ENOMEM;
> +
> + i2c_set_clientdata(i2c, bd71837);
> + bd71837->dev = &i2c->dev;
> + bd71837->i2c_client = i2c;
> + bd71837->chip_irq = board_info->gpio_intr;
> +
> + bd71837->regmap = devm_regmap_init_i2c(i2c, &bd71837_regmap_config);
> + if (IS_ERR(bd71837->regmap)) {
> + ret = PTR_ERR(bd71837->regmap);
> + dev_err(&i2c->dev, "regmap initialization failed: %d\n", ret);
> + goto err_out;
> + }
> +
> + ret = bd71837_reg_read(bd71837, BD71837_REG_REV);
> + if (ret < 0) {
> + dev_err(bd71837->dev,
> + "%s(): Read BD71837_REG_DEVICE failed!\n", __func__);
> + goto err_out;
> + }
> +
> + ret = regmap_add_irq_chip(bd71837->regmap, bd71837->chip_irq,
> + IRQF_ONESHOT, 0,
> + &bd71837_irq_chip, &bd71837->irq_data);

I think that you can use 'devm_regmap_add_irq_chip' here and remove
the code to delete the irq chip

> + if (ret < 0) {
> + dev_err(bd71837->dev, "Failed to add irq_chip %d\n", ret);
> + goto err_out;
> + }
> +
> + ret = mfd_add_devices(bd71837->dev, PLATFORM_DEVID_AUTO,
> + bd71837_mfd_cells, ARRAY_SIZE(bd71837_mfd_cells),
> + NULL, 0,
> + regmap_irq_get_domain(bd71837->irq_data));

Same here, I think you can use the devm_mfd_add_devices.

> + if (ret)
> + regmap_del_irq_chip(bd71837->chip_irq, bd71837->irq_data);

If you use devm_ functions you can remove this.

> +err_out:
> +
> + return ret;
> +}
> +
> +static int bd71837_i2c_remove(struct i2c_client *i2c)
> +{
> + struct bd71837 *bd71837 = i2c_get_clientdata(i2c);
> +
> + bd71837_irq_exit(bd71837);
> + mfd_remove_devices(bd71837->dev);

All this can go away if you use the devm_ calls.

> +
> + return 0;
> +}
> +
> +static const struct i2c_device_id bd71837_i2c_id[] = {
> + { .name = "bd71837", },
> + { }

nit: { /* sentinel */ }

> +};
> +MODULE_DEVICE_TABLE(i2c, bd71837_i2c_id);
> +
> +static struct i2c_driver bd71837_i2c_driver = {
> + .driver = {
> + .name = "bd71837-mfd",
> + .owner = THIS_MODULE,

Remove this, it is not needed, the core does it for you.

> + .of_match_table = of_match_ptr(bd71837_of_match),

The driver is DT-only, don't need to call of_match_ptr.

> + },
> + .probe = bd71837_i2c_probe,
> + .remove = bd71837_i2c_remove,
> + .id_table = bd71837_i2c_id,
> +};
> +
> +static int __init bd71837_i2c_init(void)
> +{
> + return i2c_add_driver(&bd71837_i2c_driver);
> +}
> +/* init early so consumer devices can complete system boot */
> +subsys_initcall(bd71837_i2c_init);
> +
> +static void __exit bd71837_i2c_exit(void)
> +{
> + i2c_del_driver(&bd71837_i2c_driver);
> +}
> +module_exit(bd71837_i2c_exit);
> +

Can't you use module_i2c_driver here and get rid of init/exit calls?

> +MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@xxxxxxxxxxxxxxxxx>");
> +MODULE_DESCRIPTION("BD71837 chip multi-function driver");
> +MODULE_LICENSE("GPL");

License mismatch.

> diff --git a/include/linux/mfd/bd71837.h b/include/linux/mfd/bd71837.h
> new file mode 100644
> index 000000000000..125c7478ec29
> --- /dev/null
> +++ b/include/linux/mfd/bd71837.h
> @@ -0,0 +1,367 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/* Copyright (C) 2018 ROHM Semiconductors */
> +
> +/*
> + * ROHM BD71837MWV header file
> + */
> +
> +#ifndef __LINUX_MFD_BD71837_H__
> +#define __LINUX_MFD_BD71837_H__
> +
> +#include <linux/regmap.h>
> +
> +enum {
> + BD71837_BUCK1 = 0,
> + BD71837_BUCK2,
> + BD71837_BUCK3,
> + BD71837_BUCK4,
> + BD71837_BUCK5,
> + BD71837_BUCK6,
> + BD71837_BUCK7,
> + BD71837_BUCK8,
> + BD71837_LDO1,
> + BD71837_LDO2,
> + BD71837_LDO3,
> + BD71837_LDO4,
> + BD71837_LDO5,
> + BD71837_LDO6,
> + BD71837_LDO7,
> + BD71837_REGULATOR_CNT,
> +};
> +
> +#define BD71837_BUCK1_VOLTAGE_NUM 0x40
> +#define BD71837_BUCK2_VOLTAGE_NUM 0x40
> +#define BD71837_BUCK3_VOLTAGE_NUM 0x40
> +#define BD71837_BUCK4_VOLTAGE_NUM 0x40
> +
> +#define BD71837_BUCK5_VOLTAGE_NUM 0x08
> +#define BD71837_BUCK6_VOLTAGE_NUM 0x04
> +#define BD71837_BUCK7_VOLTAGE_NUM 0x08
> +#define BD71837_BUCK8_VOLTAGE_NUM 0x40
> +
> +#define BD71837_LDO1_VOLTAGE_NUM 0x04
> +#define BD71837_LDO2_VOLTAGE_NUM 0x02
> +#define BD71837_LDO3_VOLTAGE_NUM 0x10
> +#define BD71837_LDO4_VOLTAGE_NUM 0x10
> +#define BD71837_LDO5_VOLTAGE_NUM 0x10
> +#define BD71837_LDO6_VOLTAGE_NUM 0x10
> +#define BD71837_LDO7_VOLTAGE_NUM 0x10
> +
> +enum {
> + BD71837_REG_REV = 0x00,
> + BD71837_REG_SWRESET = 0x01,
> + BD71837_REG_I2C_DEV = 0x02,
> + BD71837_REG_PWRCTRL0 = 0x03,
> + BD71837_REG_PWRCTRL1 = 0x04,
> + BD71837_REG_BUCK1_CTRL = 0x05,
> + BD71837_REG_BUCK2_CTRL = 0x06,
> + BD71837_REG_BUCK3_CTRL = 0x07,
> + BD71837_REG_BUCK4_CTRL = 0x08,
> + BD71837_REG_BUCK5_CTRL = 0x09,
> + BD71837_REG_BUCK6_CTRL = 0x0A,
> + BD71837_REG_BUCK7_CTRL = 0x0B,
> + BD71837_REG_BUCK8_CTRL = 0x0C,
> + BD71837_REG_BUCK1_VOLT_RUN = 0x0D,
> + BD71837_REG_BUCK1_VOLT_IDLE = 0x0E,
> + BD71837_REG_BUCK1_VOLT_SUSP = 0x0F,
> + BD71837_REG_BUCK2_VOLT_RUN = 0x10,
> + BD71837_REG_BUCK2_VOLT_IDLE = 0x11,
> + BD71837_REG_BUCK3_VOLT_RUN = 0x12,
> + BD71837_REG_BUCK4_VOLT_RUN = 0x13,
> + BD71837_REG_BUCK5_VOLT = 0x14,
> + BD71837_REG_BUCK6_VOLT = 0x15,
> + BD71837_REG_BUCK7_VOLT = 0x16,
> + BD71837_REG_BUCK8_VOLT = 0x17,
> + BD71837_REG_LDO1_VOLT = 0x18,
> + BD71837_REG_LDO2_VOLT = 0x19,
> + BD71837_REG_LDO3_VOLT = 0x1A,
> + BD71837_REG_LDO4_VOLT = 0x1B,
> + BD71837_REG_LDO5_VOLT = 0x1C,
> + BD71837_REG_LDO6_VOLT = 0x1D,
> + BD71837_REG_LDO7_VOLT = 0x1E,
> + BD71837_REG_TRANS_COND0 = 0x1F,
> + BD71837_REG_TRANS_COND1 = 0x20,
> + BD71837_REG_VRFAULTEN = 0x21,
> + BD71837_REG_MVRFLTMASK0 = 0x22,
> + BD71837_REG_MVRFLTMASK1 = 0x23,
> + BD71837_REG_MVRFLTMASK2 = 0x24,
> + BD71837_REG_RCVCFG = 0x25,
> + BD71837_REG_RCVNUM = 0x26,
> + BD71837_REG_PWRONCONFIG0 = 0x27,
> + BD71837_REG_PWRONCONFIG1 = 0x28,
> + BD71837_REG_RESETSRC = 0x29,
> + BD71837_REG_MIRQ = 0x2A,
> + BD71837_REG_IRQ = 0x2B,
> + BD71837_REG_IN_MON = 0x2C,
> + BD71837_REG_POW_STATE = 0x2D,
> + BD71837_REG_OUT32K = 0x2E,
> + BD71837_REG_REGLOCK = 0x2F,
> + BD71837_REG_OTPVER = 0xFF,
> + BD71837_MAX_REGISTER = 0x100,
> +};
> +
> +#define REGLOCK_PWRSEQ 0x1
> +#define REGLOCK_VREG 0x10
> +
> +/* Generic BUCK control masks */
> +#define BD71837_BUCK_SEL 0x02
> +#define BD71837_BUCK_EN 0x01
> +#define BD71837_BUCK_RUN_ON 0x04
> +
> +/* Generic LDO masks */
> +#define BD71837_LDO_SEL 0x80
> +#define BD71837_LDO_EN 0x40
> +
> +/* BD71837 BUCK ramp rate CTRL reg bits */
> +#define BUCK_RAMPRATE_MASK 0xC0
> +#define BUCK_RAMPRATE_10P00MV 0x0
> +#define BUCK_RAMPRATE_5P00MV 0x1
> +#define BUCK_RAMPRATE_2P50MV 0x2
> +#define BUCK_RAMPRATE_1P25MV 0x3
> +
> +/* BD71837_REG_BUCK1_VOLT_RUN bits */
> +#define BUCK1_RUN_MASK 0x3F
> +#define BUCK1_RUN_DEFAULT 0x14
> +
> +/* BD71837_REG_BUCK1_VOLT_SUSP bits */
> +#define BUCK1_SUSP_MASK 0x3F
> +#define BUCK1_SUSP_DEFAULT 0x14
> +
> +/* BD71837_REG_BUCK1_VOLT_IDLE bits */
> +#define BUCK1_IDLE_MASK 0x3F
> +#define BUCK1_IDLE_DEFAULT 0x14
> +
> +/* BD71837_REG_BUCK2_VOLT_RUN bits */
> +#define BUCK2_RUN_MASK 0x3F
> +#define BUCK2_RUN_DEFAULT 0x1E
> +
> +/* BD71837_REG_BUCK2_VOLT_IDLE bits */
> +#define BUCK2_IDLE_MASK 0x3F
> +#define BUCK2_IDLE_DEFAULT 0x14
> +
> +/* BD71837_REG_BUCK3_VOLT_RUN bits */
> +#define BUCK3_RUN_MASK 0x3F
> +#define BUCK3_RUN_DEFAULT 0x1E
> +
> +/* BD71837_REG_BUCK4_VOLT_RUN bits */
> +#define BUCK4_RUN_MASK 0x3F
> +#define BUCK4_RUN_DEFAULT 0x1E
> +
> +/* BD71837_REG_BUCK5_VOLT bits */
> +#define BUCK5_MASK 0x07
> +#define BUCK5_DEFAULT 0x02
> +
> +/* BD71837_REG_BUCK6_VOLT bits */
> +#define BUCK6_MASK 0x03
> +#define BUCK6_DEFAULT 0x03
> +
> +/* BD71837_REG_BUCK7_VOLT bits */
> +#define BUCK7_MASK 0x07
> +#define BUCK7_DEFAULT 0x03
> +
> +/* BD71837_REG_BUCK8_VOLT bits */
> +#define BUCK8_MASK 0x3F
> +#define BUCK8_DEFAULT 0x1E
> +
> +/* BD71837_REG_IRQ bits */
> +#define IRQ_SWRST 0x40
> +#define IRQ_PWRON_S 0x20
> +#define IRQ_PWRON_L 0x10
> +#define IRQ_PWRON 0x08
> +#define IRQ_WDOG 0x04
> +#define IRQ_ON_REQ 0x02
> +#define IRQ_STBY_REQ 0x01
> +
> +/* BD71837_REG_OUT32K bits */
> +#define BD71837_OUT32K_EN 0x01
> +
> +/* BD71837 gated clock rate */
> +#define BD71837_CLK_RATE 32768
> +
> +/* BD71837 irqs */
> +enum {
> + BD71837_INT_STBY_REQ,
> + BD71837_INT_ON_REQ,
> + BD71837_INT_WDOG,
> + BD71837_INT_PWRBTN,
> + BD71837_INT_PWRBTN_L,
> + BD71837_INT_PWRBTN_S,
> + BD71837_INT_SWRST
> +};
> +
> +/* BD71837 interrupt masks */
> +#define BD71837_INT_SWRST_MASK 0x40
> +#define BD71837_INT_PWRBTN_S_MASK 0x20
> +#define BD71837_INT_PWRBTN_L_MASK 0x10
> +#define BD71837_INT_PWRBTN_MASK 0x8
> +#define BD71837_INT_WDOG_MASK 0x4
> +#define BD71837_INT_ON_REQ_MASK 0x2
> +#define BD71837_INT_STBY_REQ_MASK 0x1
> +
> +/* BD71837_REG_LDO1_VOLT bits */
> +#define LDO1_MASK 0x03
> +
> +/* BD71837_REG_LDO1_VOLT bits */
> +#define LDO2_MASK 0x20
> +
> +/* BD71837_REG_LDO3_VOLT bits */
> +#define LDO3_MASK 0x0F
> +
> +/* BD71837_REG_LDO4_VOLT bits */
> +#define LDO4_MASK 0x0F
> +
> +/* BD71837_REG_LDO5_VOLT bits */
> +#define LDO5_MASK 0x0F
> +
> +/* BD71837_REG_LDO6_VOLT bits */
> +#define LDO6_MASK 0x0F
> +
> +/* BD71837_REG_LDO7_VOLT bits */
> +#define LDO7_MASK 0x0F
> +
> +/* register write induced reset settings */

/* Register ...

> +
> +/* even though the bit zero is not SWRESET type we still want to write zero

/*
* Even

> + * to it when changing type. Biz zero is 'SWRESET' trigger bit and if we

s/Biz/Bit/

> + * write 1 to it we will trigger the action. So always write 0 to it when
> + * changning SWRESET action - no matter what we read from it.
> + */
> +#define BD71837_SWRESET_TYPE_MASK 7
> +#define BD71837_SWRESET_TYPE_DISABLED 0
> +#define BD71837_SWRESET_TYPE_COLD 4
> +#define BD71837_SWRESET_TYPE_WARM 6
> +
> +#define BD71837_SWRESET_RESET_MASK 1
> +#define BD71837_SWRESET_RESET 1
> +
> +/* Poweroff state transition conditions */
> +
> +#define BD718XX_ON_REQ_POWEROFF_MASK 1
> +#define BD718XX_SWRESET_POWEROFF_MASK 2
> +#define BD718XX_WDOG_POWEROFF_MASK 4
> +#define BD718XX_KEY_L_POWEROFF_MASK 8
> +
> +#define BD718XX_POWOFF_TO_SNVS 0
> +#define BD718XX_POWOFF_TO_RDY 0xF
> +
> +#define BD718XX_POWOFF_TIME_MASK 0xF0
> +enum {
> + BD718XX_POWOFF_TIME_5MS = 0,
> + BD718XX_POWOFF_TIME_10MS,
> + BD718XX_POWOFF_TIME_15MS,
> + BD718XX_POWOFF_TIME_20MS,
> + BD718XX_POWOFF_TIME_25MS,
> + BD718XX_POWOFF_TIME_30MS,
> + BD718XX_POWOFF_TIME_35MS,
> + BD718XX_POWOFF_TIME_40MS,
> + BD718XX_POWOFF_TIME_45MS,
> + BD718XX_POWOFF_TIME_50MS,
> + BD718XX_POWOFF_TIME_75MS,
> + BD718XX_POWOFF_TIME_100MS,
> + BD718XX_POWOFF_TIME_250MS,
> + BD718XX_POWOFF_TIME_500MS,
> + BD718XX_POWOFF_TIME_750MS,
> + BD718XX_POWOFF_TIME_1500MS
> +};
> +
> +/* Poweron sequence state transition conditions */
> +
> +#define BD718XX_RDY_TO_SNVS_MASK 0xF
> +#define BD718XX_SNVS_TO_RUN_MASK 0xF0
> +
> +#define BD718XX_PWR_TRIG_KEY_L 1
> +#define BD718XX_PWR_TRIG_KEY_S 2
> +#define BD718XX_PWR_TRIG_PMIC_ON 4
> +#define BD718XX_PWR_TRIG_VSYS_UVLO 8
> +#define BD718XX_RDY_TO_SNVS_SIFT 0
> +#define BD718XX_SNVS_TO_RUN_SIFT 4
> +
> +/* Timeout value for detecting short press */
> +
> +#define BD718XX_PWRBTN_SHORT_PRESS_MASK 0xF
> +
> +enum {
> + BD718XX_PWRBTN_SHORT_PRESS_10MS = 0,
> + BD718XX_PWRBTN_SHORT_PRESS_500MS,
> + BD718XX_PWRBTN_SHORT_PRESS_1000MS,
> + BD718XX_PWRBTN_SHORT_PRESS_1500MS,
> + BD718XX_PWRBTN_SHORT_PRESS_2000MS,
> + BD718XX_PWRBTN_SHORT_PRESS_2500MS,
> + BD718XX_PWRBTN_SHORT_PRESS_3000MS,
> + BD718XX_PWRBTN_SHORT_PRESS_3500MS,
> + BD718XX_PWRBTN_SHORT_PRESS_4000MS,
> + BD718XX_PWRBTN_SHORT_PRESS_4500MS,
> + BD718XX_PWRBTN_SHORT_PRESS_5000MS,
> + BD718XX_PWRBTN_SHORT_PRESS_5500MS,
> + BD718XX_PWRBTN_SHORT_PRESS_6000MS,
> + BD718XX_PWRBTN_SHORT_PRESS_6500MS,
> + BD718XX_PWRBTN_SHORT_PRESS_7000MS,
> + BD718XX_PWRBTN_SHORT_PRESS_7500MS
> +};
> +
> +struct bd71837;
> +struct bd71837_pmic;
> +struct bd71837_clk;
> +struct bd718xx_pwrkey;
> +
> +/*
> + * Board platform data may be used to initialize regulators.
> + */
> +
> +struct bd71837_board {
> + struct regulator_init_data *init_data[BD71837_REGULATOR_CNT];
> + int gpio_intr;
> +};
> +
> +struct bd71837 {
> + struct device *dev;
> + struct i2c_client *i2c_client;
> + struct regmap *regmap;
> + unsigned long int id;
> +
> + int chip_irq;
> + struct regmap_irq_chip_data *irq_data;
> +
> + struct bd71837_pmic *pmic;
> + struct bd71837_clk *clk;
> + struct bd718xx_pwrkey *pwrkey;
> +};
> +
> +/*
> + * bd71837 sub-driver chip access routines
> + */
> +

All these access routines only hide the regmap_* calls, so why not use
the regmap calls directly in the driver and remove all this?

> +static inline int bd71837_reg_read(struct bd71837 *bd71837, u8 reg)
> +{
> + int r, val;
> +
> + r = regmap_read(bd71837->regmap, reg, &val);
> + if (r < 0)
> + return r;
> + return val;
> +}
> +
> +static inline int bd71837_reg_write(struct bd71837 *bd71837, u8 reg,
> + unsigned int val)
> +{
> + return regmap_write(bd71837->regmap, reg, val);
> +}
> +
> +static inline int bd71837_set_bits(struct bd71837 *bd71837, u8 reg, u8 mask)
> +{
> + return regmap_update_bits(bd71837->regmap, reg, mask, mask);
> +}
> +
> +static inline int bd71837_clear_bits(struct bd71837 *bd71837, u8 reg,
> + u8 mask)
> +{
> + return regmap_update_bits(bd71837->regmap, reg, mask, 0);
> +}
> +
> +static inline int bd71837_update_bits(struct bd71837 *bd71837, u8 reg,
> + u8 mask, u8 val)
> +{
> + return regmap_update_bits(bd71837->regmap, reg, mask, val);
> +}
> +
> +#endif /* __LINUX_MFD_BD71837_H__ */
> --
> 2.14.3
>

Next message: Paolo Bonzini: "Re: [PATCH v2] kvm: x86: mmu: Add cast to negated bitmasks in update_permission_bitmask()"
Previous message: Peter Zijlstra: "Re: [RFC PATCH 06/16] x86/split_lock: Save #AC setting for split lock in firmware in boot time and restore the setting in reboot"
Next in thread: Matti Vaittinen: "Re: [PATCH v7 1/4] mfd: bd71837: mfd driver for ROHM BD71837 PMIC"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]