Re: [PATCH v5 0/7] add virt-dma support for imx-sdma

[Lucas Stach]

Hi Robin,

I've tested this whole series with the SDMA being used for SPI, UART
and SSI with no regressions spotted. As this should cover most common
use-cases, I think this series is good to go in.

Tested-by: Lucas Stach <l.stach@xxxxxxxxxxxxxx>

Regards,
Lucas

Am Mittwoch, den 20.06.2018, 00:56 +0800 schrieb Robin Gong:
> The legacy sdma driver has below limitations or drawbacks:
> Â 1. Hardcode the max BDs number as "PAGE_SIZE / sizeof(*)", and alloc
> ÂÂÂÂÂone page size for one channel regardless of only few BDs needed
> ÂÂÂÂÂmost time. But in few cases, the max PAGE_SIZE maybe not enough.
> Â 2. One SDMA channel can't stop immediatley once channel disabled which
> ÂÂÂÂÂmeans SDMA interrupt may come in after this channel terminated.There
> ÂÂÂÂÂare some patches for this corner case such as commit "2746e2c389f9",
> ÂÂÂÂÂbut not cover non-cyclic.
> 
> The common virt-dma overcomes the above limitations. It can alloc bd
> dynamically and free bd once this tx transfer done. No memory wasted or
> maximum limititation here, only depends on how many memory can be requested
> from kernel. For No.2, such issue can be workaround by checking if there
> is available descript("sdmac->desc") now once the unwanted interrupt
> coming. At last the common virt-dma is easier for sdma driver maintain.
> 
> Change from v4:
> Â 1. identify lockdep issue which caused by allocate memory with
> ÂÂÂÂÂ'GFP_KERNEL', change to 'GFP_NOWAIT' instead so that lockdep
> ÂÂÂÂÂignore check. That also make sense since Audio/uart driver may
> ÂÂÂÂÂcall dma function after spin_lock_irqsave()...
> Â 2. use dma pool instead for bd description allocated,since audio
> ÂÂÂÂÂdriver may call dma_terminate_all in irq. Please refer to 7/7.
> Â 3. remove 7/7 serial patch in v4, since lockdep issued fixed by No.1Â
> 
> Change from v3:
> Â 1. add two uart patches which impacted by this patchset.
> Â 2. unlock 'vc.lock' before cyclic dma callback and lock again after
> ÂÂÂÂÂit because some driver such as uart will call dmaengine_tx_status
> ÂÂÂÂÂwhich will acquire 'vc.lock' again and dead lock comes out.
> Â 3. remove 'Revert commit' stuff since that patch is not wrong and
> ÂÂÂÂÂcombine two patch into one patch as Sascha's comment.
> 
> Change from v2:
> Â 1. include Sascha's patch to make the main patch easier to review.
> ÂÂÂÂÂThanks Sacha.
> Â 2. remove useless 'desc'/'chan' in struct sdma_channe.
> 
> Change from v1:
> Â 1. split v1 patch into 5 patches.
> Â 2. remove some unnecessary condition check.
> Â 3. remove unnecessary 'pending' list.
> 
> Robin Gong (6):
> Â tty: serial: imx: correct dma cookie status
> Â dmaengine: imx-sdma: add virt-dma support
> Â dmaengine: imx-sdma: remove useless 'lock' and 'enabled' in 'struct
> ÂÂÂÂsdma_channel'
> Â dmaengine: imx-sdma: remove the maximum limitation for bd numbers
> Â dmaengine: imx-sdma: add sdma_transfer_init to decrease code overlap
> Â dmaengine: imx-sdma: alloclate bd memory from dma pool
> 
> Sascha Hauer (1):
> Â dmaengine: imx-sdma: factor out a struct sdma_desc from struct
> ÂÂÂÂsdma_channel
> 
> Âdrivers/dma/KconfigÂÂÂÂÂÂ|ÂÂÂ1 +
> Âdrivers/dma/imx-sdma.cÂÂÂ| 400 +++++++++++++++++++++++++++--------------------
> Âdrivers/tty/serial/imx.c |ÂÂÂ2 +-
> Â3 files changed, 235 insertions(+), 168 deletions(-)
>