Re: [PATCH v4 8/8] media: imx274: add SELECTION support for cropping
From: Sakari Ailus
Date: Fri Jun 29 2018 - 04:05:14 EST
On Mon, Jun 11, 2018 at 01:35:39PM +0200, Luca Ceresoli wrote:
> Currently this driver does not support cropping. The supported modes
> are the following, all capturing the entire area:
>
> - 3840x2160, 1:1 binning (native sensor resolution)
> - 1920x1080, 2:1 binning
> - 1280x720, 3:1 binning
>
> The VIDIOC_SUBDEV_S_FMT ioctl chooses among these 3 configurations the
> one that matches the requested format.
>
> Add cropping support via VIDIOC_SUBDEV_S_SELECTION: with target
> V4L2_SEL_TGT_CROP to choose the captured area, with
> V4L2_SEL_TGT_COMPOSE to choose the output resolution.
>
> To maintain backward compatibility we also allow setting the compose
> format via VIDIOC_SUBDEV_S_FMT. To obtain this, compose rect and
> output format are computed in the common helper function
> __imx274_change_compose(), which sets both to the same width/height
> values.
>
> Cropping also calls __imx274_change_compose() whenever cropping rect
> size changes in order to reset the compose rect (and output format
> size) for 1:1 binning.
>
> Also change the names in enum imx274_mode from being resolution-based
> to being binning-based (e.g. from IMX274_MODE_1920X1080 to
> IMX274_MODE_BINNING_2_1). Without cropping, the two naming are
> equivalent. With cropping, the resolution could be different,
> e.g. using 2:1 binning mode to crop 1200x960 and output a 600x480
> format. Using binning in the names avoids any misunderstanding. For
> the same reason, replace the 'size' field in struct imx274_frmfmt with
> 'bin_ratio'.
>
> Signed-off-by: Luca Ceresoli <luca@xxxxxxxxxxxxxxxx>
> Cc: Sakari Ailus <sakari.ailus@xxxxxxxxxxxxxxx>
>
> ---
> Changed v3 -> v4:
> - Set the binning via the SELECTION API (COMPOSE rect), but still
> allow using VIDIOC_SUBDEV_S_FMT for backward compatibility.
> - rename imx274_set_trimming -> imx274_apply_trimming for clarity
>
> Changed v2 -> v3:
> - Remove hard-coded HMAX reg setting from all modes, not only the
> first one. HMAX is always computed and set in s_stream now.
> - Reword commit log message.
>
> Changed v1 -> v2:
> - add "media: " prefix to commit message
> ---
> drivers/media/i2c/imx274.c | 416 +++++++++++++++++++++++++++++++++++----------
> 1 file changed, 326 insertions(+), 90 deletions(-)
>
> diff --git a/drivers/media/i2c/imx274.c b/drivers/media/i2c/imx274.c
> index 2c13961e9764..8bfc20a46b3d 100644
> --- a/drivers/media/i2c/imx274.c
> +++ b/drivers/media/i2c/imx274.c
> @@ -5,6 +5,7 @@
> *
> * Leon Luo <leonl@xxxxxxxxxxxxxxxxxx>
> * Edwin Zou <edwinz@xxxxxxxxxxxxxxxxxx>
> + * Luca Ceresoli <luca@xxxxxxxxxxxxxxxx>
> *
> * This program is free software; you can redistribute it and/or modify it
> * under the terms and conditions of the GNU General Public License,
> @@ -19,6 +20,7 @@
> * along with this program. If not, see <http://www.gnu.org/licenses/>.
> */
>
> +#include <linux/kernel.h>
Alphabetical order, please.
> #include <linux/clk.h>
> #include <linux/delay.h>
> #include <linux/gpio.h>
> @@ -74,7 +76,7 @@
> */
> #define IMX274_MIN_EXPOSURE_TIME (4 * 260 / 72)
>
> -#define IMX274_DEFAULT_MODE IMX274_MODE_3840X2160
> +#define IMX274_DEFAULT_MODE IMX274_MODE_BINNING_OFF
> #define IMX274_MAX_WIDTH (3840)
> #define IMX274_MAX_HEIGHT (2160)
> #define IMX274_MAX_FRAME_RATE (120)
> @@ -111,6 +113,20 @@
> #define IMX274_SHR_REG_LSB 0x300C /* SHR */
> #define IMX274_SVR_REG_MSB 0x300F /* SVR */
> #define IMX274_SVR_REG_LSB 0x300E /* SVR */
> +#define IMX274_HTRIM_EN_REG 0x3037
> +#define IMX274_HTRIM_START_REG_LSB 0x3038
> +#define IMX274_HTRIM_START_REG_MSB 0x3039
> +#define IMX274_HTRIM_END_REG_LSB 0x303A
> +#define IMX274_HTRIM_END_REG_MSB 0x303B
> +#define IMX274_VWIDCUTEN_REG 0x30DD
> +#define IMX274_VWIDCUT_REG_LSB 0x30DE
> +#define IMX274_VWIDCUT_REG_MSB 0x30DF
> +#define IMX274_VWINPOS_REG_LSB 0x30E0
> +#define IMX274_VWINPOS_REG_MSB 0x30E1
> +#define IMX274_WRITE_VSIZE_REG_LSB 0x3130
> +#define IMX274_WRITE_VSIZE_REG_MSB 0x3131
> +#define IMX274_Y_OUT_SIZE_REG_LSB 0x3132
> +#define IMX274_Y_OUT_SIZE_REG_MSB 0x3133
> #define IMX274_VMAX_REG_1 0x30FA /* VMAX, MSB */
> #define IMX274_VMAX_REG_2 0x30F9 /* VMAX */
> #define IMX274_VMAX_REG_3 0x30F8 /* VMAX, LSB */
> @@ -141,9 +157,9 @@ static const struct regmap_config imx274_regmap_config = {
> };
>
> enum imx274_mode {
Is this still an appropriate name? imx274_binning?
> - IMX274_MODE_3840X2160,
> - IMX274_MODE_1920X1080,
> - IMX274_MODE_1280X720,
> + IMX274_MODE_BINNING_OFF,
> + IMX274_MODE_BINNING_2_1,
> + IMX274_MODE_BINNING_3_1,
> };
>
> /*
> @@ -152,8 +168,8 @@ enum imx274_mode {
> * These are the values to configure the sensor in one of the
> * implemented modes.
> *
> - * @size: recommended recording pixels
> * @init_regs: registers to initialize the mode
> + * @bin_ratio: downscale factor (e.g. 3 for 3:1 binning)
> * @min_frame_len: Minimum frame length for each mode (see "Frame Rate
> * Adjustment (CSI-2)" in the datasheet)
> * @min_SHR: Minimum SHR register value (see "Shutter Setting (CSI-2)" in the
> @@ -163,8 +179,8 @@ enum imx274_mode {
> * in Each Readout Drive Mode (CSI-2)" in the datasheet)
> */
> struct imx274_frmfmt {
> - struct v4l2_frmsize_discrete size;
> const struct reg_8 *init_regs;
> + unsigned int bin_ratio;
> int min_frame_len;
> int min_SHR;
> int max_fps;
> @@ -215,31 +231,14 @@ static const struct reg_8 imx274_mode1_3840x2160_raw10[] = {
> {0x3004, 0x01},
> {0x3005, 0x01},
> {0x3006, 0x00},
> - {0x3007, 0x02},
> + {0x3007, 0xa2},
>
> {0x3018, 0xA2}, /* output XVS, HVS */
>
> {0x306B, 0x05},
> {0x30E2, 0x01},
> - {0x30F6, 0x07}, /* HMAX, 263 */
> - {0x30F7, 0x01}, /* HMAX */
> -
> - {0x30dd, 0x01}, /* crop to 2160 */
> - {0x30de, 0x06},
> - {0x30df, 0x00},
> - {0x30e0, 0x12},
> - {0x30e1, 0x00},
> - {0x3037, 0x01}, /* to crop to 3840 */
> - {0x3038, 0x0c},
> - {0x3039, 0x00},
> - {0x303a, 0x0c},
> - {0x303b, 0x0f},
>
> {0x30EE, 0x01},
> - {0x3130, 0x86},
> - {0x3131, 0x08},
> - {0x3132, 0x7E},
> - {0x3133, 0x08},
> {0x3342, 0x0A},
> {0x3343, 0x00},
> {0x3344, 0x16},
> @@ -273,32 +272,14 @@ static const struct reg_8 imx274_mode3_1920x1080_raw10[] = {
> {0x3004, 0x02},
> {0x3005, 0x21},
> {0x3006, 0x00},
> - {0x3007, 0x11},
> + {0x3007, 0xb1},
>
> {0x3018, 0xA2}, /* output XVS, HVS */
>
> {0x306B, 0x05},
> {0x30E2, 0x02},
>
> - {0x30F6, 0x04}, /* HMAX, 260 */
> - {0x30F7, 0x01}, /* HMAX */
> -
> - {0x30dd, 0x01}, /* to crop to 1920x1080 */
> - {0x30de, 0x05},
> - {0x30df, 0x00},
> - {0x30e0, 0x04},
> - {0x30e1, 0x00},
> - {0x3037, 0x01},
> - {0x3038, 0x0c},
> - {0x3039, 0x00},
> - {0x303a, 0x0c},
> - {0x303b, 0x0f},
> -
> {0x30EE, 0x01},
> - {0x3130, 0x4E},
> - {0x3131, 0x04},
> - {0x3132, 0x46},
> - {0x3133, 0x04},
> {0x3342, 0x0A},
> {0x3343, 0x00},
> {0x3344, 0x1A},
> @@ -331,31 +312,14 @@ static const struct reg_8 imx274_mode5_1280x720_raw10[] = {
> {0x3004, 0x03},
> {0x3005, 0x31},
> {0x3006, 0x00},
> - {0x3007, 0x09},
> + {0x3007, 0xa9},
>
> {0x3018, 0xA2}, /* output XVS, HVS */
>
> {0x306B, 0x05},
> {0x30E2, 0x03},
>
> - {0x30F6, 0x04}, /* HMAX, 260 */
> - {0x30F7, 0x01}, /* HMAX */
> -
> - {0x30DD, 0x01},
> - {0x30DE, 0x07},
> - {0x30DF, 0x00},
> - {0x40E0, 0x04},
> - {0x30E1, 0x00},
> - {0x3030, 0xD4},
> - {0x3031, 0x02},
> - {0x3032, 0xD0},
> - {0x3033, 0x02},
> -
> {0x30EE, 0x01},
> - {0x3130, 0xE2},
> - {0x3131, 0x02},
> - {0x3132, 0xDE},
> - {0x3133, 0x02},
> {0x3342, 0x0A},
> {0x3343, 0x00},
> {0x3344, 0x1B},
> @@ -498,7 +462,7 @@ static const struct reg_8 imx274_tp_regs[] = {
> static const struct imx274_frmfmt imx274_formats[] = {
> {
> /* mode 1, 4K */
> - .size = {3840, 2160},
> + .bin_ratio = 1,
> .init_regs = imx274_mode1_3840x2160_raw10,
> .min_frame_len = 4550,
> .min_SHR = 12,
> @@ -507,7 +471,7 @@ static const struct imx274_frmfmt imx274_formats[] = {
> },
> {
> /* mode 3, 1080p */
> - .size = {1920, 1080},
> + .bin_ratio = 2,
> .init_regs = imx274_mode3_1920x1080_raw10,
> .min_frame_len = 2310,
> .min_SHR = 8,
> @@ -516,7 +480,7 @@ static const struct imx274_frmfmt imx274_formats[] = {
> },
> {
> /* mode 5, 720p */
> - .size = {1280, 720},
> + .bin_ratio = 3,
> .init_regs = imx274_mode5_1280x720_raw10,
> .min_frame_len = 2310,
> .min_SHR = 8,
> @@ -547,7 +511,10 @@ struct imx274_ctrls {
> * @pad: Media pad structure
> * @client: Pointer to I2C client
> * @ctrls: imx274 control structure
> + * @crop: rect to be captured
> + * @compose: compose rect, i.e. output resolution
> * @format: V4L2 media bus frame format structure
> + * (width and height are in sync with the compose rect)
> * @frame_rate: V4L2 frame rate structure
> * @regmap: Pointer to regmap structure
> * @reset_gpio: Pointer to reset gpio
> @@ -559,6 +526,8 @@ struct stimx274 {
> struct media_pad pad;
> struct i2c_client *client;
> struct imx274_ctrls ctrls;
> + struct v4l2_rect crop;
> + struct v4l2_rect compose;
> struct v4l2_mbus_framefmt format;
> struct v4l2_fract frame_interval;
> struct regmap *regmap;
> @@ -864,6 +833,80 @@ static int imx274_s_ctrl(struct v4l2_ctrl *ctrl)
> }
>
> /**
> + * Helper function to change binning and set both compose and format.
> + *
> + * We have two entry points to change binning: set_fmt and
> + * set_selection(COMPOSE). Both have to compute the new output size
> + * and set it in both the compose rect and the frame format size. We
> + * also need to do the same things after setting cropping to restore
> + * 1:1 binning.
> + *
> + * This function contains the common code for these three cases, it
> + * has many arguments in order to accomodate the needs of all of them.
> + *
> + * Must be called with imx274->lock locked.
> + *
> + * @imx274 The device object
Colon after the name of the argument. Same below.
> + * @cfg The pad config we are editing for TRY requests
> + * @which V4L2_SUBDEV_FORMAT_ACTIVE or V4L2_SUBDEV_FORMAT_TRY from the caller
> + * @width Input-output parameter: set to the desired width before
> + * the call, contains the chosen value after returning successfully
> + * @height Input-output parameter for height (see @width)
> + */
> +static int __imx274_change_compose(struct stimx274 *imx274,
> + struct v4l2_subdev_pad_config *cfg,
> + u32 which,
> + u32 *width,
> + u32 *height)
> +{
> + struct device *dev = &imx274->client->dev;
> + const struct v4l2_rect *cur_crop;
> + struct v4l2_mbus_framefmt *tgt_fmt;
> + struct v4l2_rect *tgt_compose;
> + unsigned int ratio; /* Binning ratio */
> +
> + dev_dbg(dev, "%s: request of %dx%d (%s)\n",
> + __func__, *width, *height,
> + (which == V4L2_SUBDEV_FORMAT_ACTIVE) ? "ACTIVE" : "TRY");
If these's a need for such debug prints, I think they'd be better added to
the framework than individual drivers.
> +
> + if (which == V4L2_SUBDEV_FORMAT_TRY) {
> + cur_crop = &cfg->try_crop;
> + tgt_compose = &cfg->try_compose;
> + tgt_fmt = &cfg->try_fmt;
> + } else {
> + cur_crop = &imx274->crop;
> + tgt_compose = &imx274->compose;
> + tgt_fmt = &imx274->format;
> + }
> +
> + /* Find ratio (maximize output resolution). Fallback to 1:1. */
> + for (ratio = 3; ratio > 1; ratio--)
> + if (*width <= DIV_ROUND_UP(cur_crop->width, ratio) &&
> + *height <= DIV_ROUND_UP(cur_crop->height, ratio))
> + break;
There are flags to direct the rounding behaviour. The default is the
nearest:
<URL:https://hverkuil.home.xs4all.nl/spec/uapi/v4l/v4l2-selection-flags.html>
The smiapp driver (as the only sensor driver) supports them.
> +
> + *width = cur_crop->width / ratio;
> + *height = cur_crop->height / ratio;
> +
> + if (which == V4L2_SUBDEV_FORMAT_ACTIVE)
> + imx274->mode = &imx274_formats[ratio - 1];
> +
> + dev_dbg(dev, "%s: adjusted to %dx%d (%d:1 binning)\n",
> + __func__, *width, *height, ratio);
Could be here, for binning. %d -> %u --- it's unsigned.
> +
> + tgt_compose->top = 0;
> + tgt_compose->left = 0;
> + tgt_compose->width = *width;
> + tgt_compose->height = *height;
> +
> + tgt_fmt->width = *width;
> + tgt_fmt->height = *height;
> + tgt_fmt->field = V4L2_FIELD_NONE;
> +
> + return 0;
> +}
> +
> +/**
> * imx274_get_fmt - Get the pad format
> * @sd: Pointer to V4L2 Sub device structure
> * @cfg: Pointer to sub device pad information structure
> @@ -901,45 +944,228 @@ static int imx274_set_fmt(struct v4l2_subdev *sd,
> {
> struct v4l2_mbus_framefmt *fmt = &format->format;
> struct stimx274 *imx274 = to_imx274(sd);
> - struct i2c_client *client = imx274->client;
> - int index;
> -
> - dev_dbg(&client->dev,
> - "%s: width = %d height = %d code = %d\n",
> - __func__, fmt->width, fmt->height, fmt->code);
> + int err = 0;
>
> mutex_lock(&imx274->lock);
>
> - for (index = 0; index < ARRAY_SIZE(imx274_formats); index++) {
> - if (imx274_formats[index].size.width == fmt->width &&
> - imx274_formats[index].size.height == fmt->height)
> - break;
> - }
> -
> - if (index >= ARRAY_SIZE(imx274_formats)) {
> - /* default to first format */
> - index = 0;
> - }
> + err = __imx274_change_compose(imx274, cfg, format->which,
> + &fmt->width, &fmt->height);
>
> - imx274->mode = &imx274_formats[index];
> + if (err)
> + goto out;
>
> - if (fmt->width > IMX274_MAX_WIDTH)
> - fmt->width = IMX274_MAX_WIDTH;
> - if (fmt->height > IMX274_MAX_HEIGHT)
> - fmt->height = IMX274_MAX_HEIGHT;
> - fmt->width = fmt->width & (~IMX274_MASK_LSB_2_BITS);
> - fmt->height = fmt->height & (~IMX274_MASK_LSB_2_BITS);
> + /*
> + * __imx274_change_compose already set width and height in the
> + * applicable format, but we need to keep all other format
> + * values, so do a full copy here
> + */
> fmt->field = V4L2_FIELD_NONE;
> -
> if (format->which == V4L2_SUBDEV_FORMAT_TRY)
> cfg->try_fmt = *fmt;
> else
> imx274->format = *fmt;
>
> +out:
> mutex_unlock(&imx274->lock);
> +
> + return err;
> +}
> +
> +static int imx274_get_selection(struct v4l2_subdev *sd,
> + struct v4l2_subdev_pad_config *cfg,
> + struct v4l2_subdev_selection *sel)
> +{
> + struct stimx274 *imx274 = to_imx274(sd);
> + const struct v4l2_rect *src_crop;
> + const struct v4l2_rect *src_compose;
> + int ret = 0;
> +
> + if (sel->pad != 0)
> + return -EINVAL;
> +
> + if (sel->target == V4L2_SEL_TGT_CROP_BOUNDS) {
> + sel->r.left = 0;
> + sel->r.top = 0;
> + sel->r.width = IMX274_MAX_WIDTH;
> + sel->r.height = IMX274_MAX_HEIGHT;
> + return 0;
> + }
> +
> + if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
> + src_crop = &cfg->try_crop;
> + src_compose = &cfg->try_compose;
> + } else {
> + src_crop = &imx274->crop;
> + src_compose = &imx274->compose;
> + }
> +
> + mutex_lock(&imx274->lock);
> +
> + switch (sel->target) {
> + case V4L2_SEL_TGT_CROP:
> + sel->r = *src_crop;
> + break;
> + case V4L2_SEL_TGT_COMPOSE_BOUNDS:
> + sel->r.top = 0;
> + sel->r.left = 0;
> + sel->r.width = src_crop->width;
> + sel->r.height = src_crop->height;
> + break;
> + case V4L2_SEL_TGT_COMPOSE:
> + sel->r = *src_compose;
> + break;
> + default:
> + ret = -EINVAL;
> + }
> +
> + mutex_unlock(&imx274->lock);
> +
> + return ret;
> +}
> +
> +static int imx274_set_selection_crop(struct stimx274 *imx274,
> + struct v4l2_subdev_pad_config *cfg,
> + struct v4l2_subdev_selection *sel)
> +{
> + struct device *dev = &imx274->client->dev;
> + struct v4l2_rect *tgt_crop;
> + struct v4l2_rect new_crop;
> + bool size_changed;
> +
> + /*
> + * h_step could be 12 or 24 depending on the binning. But we
> + * won't know the binning until we choose the mode later in
> + * imx274_set_fmt(). Thus let's be safe and use the most
> + * conservative value in all cases.
> + */
> + const int h_step = 24;
> +
> + dev_dbg(dev, "%s: request of (%d,%d)%dx%d (%s)\n", __func__,
> + sel->r.left, sel->r.top, sel->r.width, sel->r.height,
> + V4L2_SUBDEV_FORMAT_ACTIVE ? "ACTIVE" : "TRY");
> +
> + new_crop.width = rounddown(min_t(u32, sel->r.width, IMX274_MAX_WIDTH),
> + h_step);
> +
> + /* Constraint: HTRIMMING_END - HTRIMMING_START >= 144 */
> + if (new_crop.width < 144)
> + new_crop.width = 144;
> +
> + new_crop.left = min_t(u32, roundup(sel->r.left, h_step),
> + IMX274_MAX_WIDTH - new_crop.width);
> +
> + new_crop.height =
> + ALIGN(min_t(u32, sel->r.height, IMX274_MAX_HEIGHT), 2);
> +
> + new_crop.top = min_t(u32, ALIGN(sel->r.top, 2),
> + IMX274_MAX_HEIGHT - new_crop.height);
> +
> + dev_dbg(dev, "%s: adjusted to (%d,%d)%dx%d", __func__,
> + new_crop.left, new_crop.top, new_crop.width, new_crop.height);
> +
> + sel->r = new_crop;
> +
> + if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
> + tgt_crop = &cfg->try_crop;
> + else
> + tgt_crop = &imx274->crop;
> +
> + mutex_lock(&imx274->lock);
> +
> + size_changed = (new_crop.width != tgt_crop->width ||
> + new_crop.height != tgt_crop->height);
> +
> + /* __imx274_change_compose needs the new size in *tgt_crop */
> + *tgt_crop = new_crop;
> +
> + /* if crop size changed then reset the output image size */
> + if (size_changed)
> + __imx274_change_compose(imx274, cfg, sel->which,
> + &new_crop.width, &new_crop.height);
> +
> + mutex_unlock(&imx274->lock);
> +
> return 0;
> }
>
> +static int imx274_set_selection(struct v4l2_subdev *sd,
> + struct v4l2_subdev_pad_config *cfg,
> + struct v4l2_subdev_selection *sel)
> +{
> + struct stimx274 *imx274 = to_imx274(sd);
> +
> + if (sel->pad != 0)
> + return -EINVAL;
> +
> + if (sel->target == V4L2_SEL_TGT_CROP)
> + return imx274_set_selection_crop(imx274, cfg, sel);
> +
> + if (sel->target == V4L2_SEL_TGT_COMPOSE) {
> + int err;
> +
> + mutex_lock(&imx274->lock);
> +
> + err = __imx274_change_compose(imx274, cfg, sel->which,
> + &sel->r.width, &sel->r.height);
> + /*
> + * __imx274_change_compose already set width and
> + * height in set->r, we still need to set top-left
> + */
> + if (!err) {
> + sel->r.top = 0;
> + sel->r.left = 0;
> + }
> +
> + mutex_unlock(&imx274->lock);
> +
> + return err;
> + }
> +
> + return -EINVAL;
> +}
> +
> +static int imx274_apply_trimming(struct stimx274 *imx274)
> +{
> + u32 h_start;
> + u32 h_end;
> + u32 hmax;
> + u32 v_cut;
> + s32 v_pos;
> + u32 write_v_size;
> + u32 y_out_size;
> + struct reg_8 regs[17];
> +
> + h_start = imx274->crop.left + 12;
> + h_end = h_start + imx274->crop.width;
> +
> + /* Use the minimum allowed value of HMAX */
> + /* Note: except in mode 1, (width / 16 + 23) is always < hmax_min */
> + /* Note: 260 is the minimum HMAX in all implemented modes */
> + hmax = max_t(u32, 260, (imx274->crop.width) / 16 + 23);
> +
> + /* invert v_pos if VFLIP */
> + v_pos = imx274->ctrls.vflip->cur.val ?
> + (-imx274->crop.top / 2) : (imx274->crop.top / 2);
> + v_cut = (IMX274_MAX_HEIGHT - imx274->crop.height) / 2;
> + write_v_size = imx274->crop.height + 22;
> + y_out_size = imx274->crop.height + 14;
> +
> + prepare_reg(®s[0], IMX274_HMAX_REG_LSB, hmax, 16);
> + prepare_reg(®s[2], IMX274_HTRIM_EN_REG, 1, 1);
> + prepare_reg(®s[3], IMX274_HTRIM_START_REG_LSB, h_start, 13);
> + prepare_reg(®s[5], IMX274_HTRIM_END_REG_LSB, h_end, 13);
> +
> + prepare_reg(®s[7], IMX274_VWIDCUTEN_REG, 1, 1);
> + prepare_reg(®s[8], IMX274_VWIDCUT_REG_LSB, v_cut, 11);
> + prepare_reg(®s[10], IMX274_VWINPOS_REG_LSB, v_pos, 12);
> + prepare_reg(®s[12], IMX274_WRITE_VSIZE_REG_LSB, write_v_size, 13);
> + prepare_reg(®s[14], IMX274_Y_OUT_SIZE_REG_LSB, y_out_size, 13);
> +
> + regs[16].addr = IMX274_TABLE_END;
> +
> + return imx274_write_table(imx274, regs);
> +}
> +
> /**
> * imx274_g_frame_interval - Get the frame interval
> * @sd: Pointer to V4L2 Sub device structure
> @@ -1080,6 +1306,10 @@ static int imx274_s_stream(struct v4l2_subdev *sd, int on)
> if (ret)
> goto fail;
>
> + ret = imx274_apply_trimming(imx274);
> + if (ret)
> + goto fail;
> +
> /*
> * update frame rate & expsoure. if the last mode is different,
> * HMAX could be changed. As the result, frame rate & exposure
> @@ -1589,6 +1819,8 @@ static int imx274_set_frame_interval(struct stimx274 *priv,
> static const struct v4l2_subdev_pad_ops imx274_pad_ops = {
> .get_fmt = imx274_get_fmt,
> .set_fmt = imx274_set_fmt,
> + .get_selection = imx274_get_selection,
> + .set_selection = imx274_set_selection,
> };
>
> static const struct v4l2_subdev_video_ops imx274_video_ops = {
> @@ -1634,8 +1866,12 @@ static int imx274_probe(struct i2c_client *client,
>
> /* initialize format */
> imx274->mode = &imx274_formats[IMX274_DEFAULT_MODE];
> - imx274->format.width = imx274->mode->size.width;
> - imx274->format.height = imx274->mode->size.height;
> + imx274->crop.width = IMX274_MAX_WIDTH;
> + imx274->crop.height = IMX274_MAX_HEIGHT;
> + imx274->compose.width = imx274->crop.width / imx274->mode->bin_ratio;
> + imx274->compose.height = imx274->crop.height / imx274->mode->bin_ratio;
> + imx274->format.width = imx274->compose.width;
> + imx274->format.height = imx274->compose.height;
> imx274->format.field = V4L2_FIELD_NONE;
> imx274->format.code = MEDIA_BUS_FMT_SRGGB10_1X10;
> imx274->format.colorspace = V4L2_COLORSPACE_SRGB;
> --
> 2.7.4
>
--
Sakari Ailus
sakari.ailus@xxxxxxxxxxxxxxx