[PATCH 3/5] i2c: designware: add MSCC Ocelot support
From: Alexandre Belloni
Date: Tue Jul 17 2018 - 07:48:58 EST
The Microsemi Ocelot I2C controller is a designware IP. It also has a
second set of registers to allow tweaking SDA hold time and spike
filtering.
Cc: Rob Herring <robh+dt@xxxxxxxxxx>
Signed-off-by: Alexandre Belloni <alexandre.belloni@xxxxxxxxxxx>
---
.../bindings/i2c/i2c-designware.txt | 5 ++++-
drivers/i2c/busses/i2c-designware-core.h | 1 +
drivers/i2c/busses/i2c-designware-platdrv.c | 20 +++++++++++++++++++
3 files changed, 25 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/i2c/i2c-designware.txt b/Documentation/devicetree/bindings/i2c/i2c-designware.txt
index fbb0a6d8b964..7af4176da4af 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-designware.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-designware.txt
@@ -2,7 +2,7 @@
Required properties :
- - compatible : should be "snps,designware-i2c"
+ - compatible : should be "snps,designware-i2c" or "mscc,ocelot-i2c"
- reg : Offset and length of the register set for the device
- interrupts : <IRQ> where IRQ is the interrupt number.
@@ -11,6 +11,9 @@ Recommended properties :
- clock-frequency : desired I2C bus clock frequency in Hz.
Optional properties :
+ - reg : for "mscc,ocelot-i2c", a second register set to configure the SDA hold
+ time, named ICPU_CFG:TWI_DELAY in the datasheet.
+
- i2c-sda-hold-time-ns : should contain the SDA hold time in nanoseconds.
This option is only supported in hardware blocks version 1.11a or newer.
diff --git a/drivers/i2c/busses/i2c-designware-core.h b/drivers/i2c/busses/i2c-designware-core.h
index b2778b6d8aca..37f63d084c1d 100644
--- a/drivers/i2c/busses/i2c-designware-core.h
+++ b/drivers/i2c/busses/i2c-designware-core.h
@@ -237,6 +237,7 @@
struct dw_i2c_dev {
struct device *dev;
void __iomem *base;
+ void __iomem *base_ext;
struct completion cmd_complete;
struct clk *clk;
struct reset_control *rst;
diff --git a/drivers/i2c/busses/i2c-designware-platdrv.c b/drivers/i2c/busses/i2c-designware-platdrv.c
index 5660daf6c92e..1a476a6e3551 100644
--- a/drivers/i2c/busses/i2c-designware-platdrv.c
+++ b/drivers/i2c/busses/i2c-designware-platdrv.c
@@ -204,6 +204,18 @@ static void i2c_dw_configure_slave(struct dw_i2c_dev *dev)
dev->mode = DW_IC_SLAVE;
}
+#define MSCC_ICPU_CFG_TWI_DELAY 0x0
+#define MSCC_ICPU_CFG_TWI_DELAY_ENABLE BIT(0)
+#define MSCC_ICPU_CFG_TWI_SPIKE_FILTER 0x4
+
+static int mscc_twi_set_sda_hold_time(struct dw_i2c_dev *dev)
+{
+ writel((dev->sda_hold_time << 1) | MSCC_ICPU_CFG_TWI_DELAY_ENABLE,
+ dev->base_ext + MSCC_ICPU_CFG_TWI_DELAY);
+
+ return 0;
+}
+
static void dw_i2c_set_fifo_size(struct dw_i2c_dev *dev, int id)
{
u32 param, tx_fifo_depth, rx_fifo_depth;
@@ -342,6 +354,13 @@ static int dw_i2c_plat_probe(struct platform_device *pdev)
1000000);
}
+ if (of_device_is_compatible(pdev->dev.of_node, "mscc,ocelot-i2c")) {
+ mem = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ dev->base_ext = devm_ioremap_resource(&pdev->dev, mem);
+ if (!IS_ERR(dev->base_ext))
+ dev->set_sda_hold_time = mscc_twi_set_sda_hold_time;
+ }
+
dw_i2c_set_fifo_size(dev, pdev->id);
adap = &dev->adapter;
@@ -410,6 +429,7 @@ static int dw_i2c_plat_remove(struct platform_device *pdev)
#ifdef CONFIG_OF
static const struct of_device_id dw_i2c_of_match[] = {
{ .compatible = "snps,designware-i2c", },
+ { .compatible = "mscc,ocelot-i2c", },
{},
};
MODULE_DEVICE_TABLE(of, dw_i2c_of_match);
--
2.18.0