Re: [PATCH v3 1/3] Input: edt-ft5x06 - Add support for regulator

[OndÅej Jirman]

Hello Mylène,

On Wed, Jul 18, 2018 at 08:27:17PM +0200, Mylène Josserand wrote:
> Add the support of regulator to use it as VCC source.
> 
> Signed-off-by: Mylène Josserand <mylene.josserand@xxxxxxxxxxx>
> ---
>  .../bindings/input/touchscreen/edt-ft5x06.txt      |  1 +
>  drivers/input/touchscreen/edt-ft5x06.c             | 29 ++++++++++++++++++++++
>  2 files changed, 30 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> index 025cf8c9324a..48e975b9c1aa 100644
> --- a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> +++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> @@ -30,6 +30,7 @@ Required properties:
>  Optional properties:
>   - reset-gpios: GPIO specification for the RESET input
>   - wake-gpios:  GPIO specification for the WAKE input
> + - vcc-supply:  Regulator that supplies the touchscreen
>  
>   - pinctrl-names: should be "default"
>   - pinctrl-0:   a phandle pointing to the pin settings for the
> diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
> index 1e18ca0d1b4e..aa94494b06b5 100644
> --- a/drivers/input/touchscreen/edt-ft5x06.c
> +++ b/drivers/input/touchscreen/edt-ft5x06.c
> @@ -39,6 +39,7 @@
>  #include <linux/input/mt.h>
>  #include <linux/input/touchscreen.h>
>  #include <linux/of_device.h>
> +#include <linux/regulator/consumer.h>
>  
>  #define WORK_REGISTER_THRESHOLD		0x00
>  #define WORK_REGISTER_REPORT_RATE	0x08
> @@ -91,6 +92,7 @@ struct edt_ft5x06_ts_data {
>  	struct touchscreen_properties prop;
>  	u16 num_x;
>  	u16 num_y;
> +	struct regulator *vcc;
>  
>  	struct gpio_desc *reset_gpio;
>  	struct gpio_desc *wake_gpio;
> @@ -991,6 +993,22 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
>  
>  	tsdata->max_support_points = chip_data->max_support_points;
>  
> +	tsdata->vcc = devm_regulator_get(&client->dev, "vcc");
> +	if (IS_ERR(tsdata->vcc)) {
> +		error = PTR_ERR(tsdata->vcc);
> +		if (error != -EPROBE_DEFER)
> +			dev_err(&client->dev, "failed to request regulator: %d\n",
> +				error);
> +		return error;
> +	}
> +
> +	error = regulator_enable(tsdata->vcc);
> +	if (error < 0) {
> +		dev_err(&client->dev, "failed to enable vcc: %d\n",
> +			error);
> +		return error;
> +	}
> +
>  	tsdata->reset_gpio = devm_gpiod_get_optional(&client->dev,
>  						     "reset", GPIOD_OUT_HIGH);
>  	if (IS_ERR(tsdata->reset_gpio)) {
> @@ -1120,20 +1138,31 @@ static int edt_ft5x06_ts_remove(struct i2c_client *client)
>  static int __maybe_unused edt_ft5x06_ts_suspend(struct device *dev)
>  {
>  	struct i2c_client *client = to_i2c_client(dev);
> +	struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
>  
>  	if (device_may_wakeup(dev))
>  		enable_irq_wake(client->irq);
>  
> +	regulator_disable(tsdata->vcc);
> +

How will the touchscreen wakeup the system with interrupt if you power it off
on suspend? Perhaps guard this with device_may_wakeup() too? 

>  	return 0;
>  }
>  
>  static int __maybe_unused edt_ft5x06_ts_resume(struct device *dev)
>  {
>  	struct i2c_client *client = to_i2c_client(dev);
> +	struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
> +	int ret;
>  
>  	if (device_may_wakeup(dev))
>  		disable_irq_wake(client->irq);
>  
> +	ret = regulator_enable(tsdata->vcc);
> +	if (ret < 0) {
> +		dev_err(dev, "failed to enable vcc: %d\n", ret);
> +		return ret;
> +	}
> +

Ditto.

Regards,
  o.

>  	return 0;
>  }
>  
> -- 
> 2.11.0
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel