Re: [PATCH 1/3] iio: adc: add support for mcp3911
From: Marcus Folkesson
Date: Sun Jul 22 2018 - 15:01:07 EST
Hi Jonathan,
Thanks, all good catches.
On Sun, Jul 22, 2018 at 09:08:38AM +0100, Jonathan Cameron wrote:
> On Sat, 21 Jul 2018 23:19:48 +0200 (CEST)
> Peter Meerwald-Stadler <pmeerw@xxxxxxxxxx> wrote:
>
> > Hello,
> >
> > > MCP3911 is a dual channel Analog Front End (AFE) containing two
> > > synchronous sampling delta-sigma Analog-to-Digital Converters (ADC).
> >
> > some comments below...
>
> +CC Mark for the unusual SPI addressing stuff. I'm mostly interested in what
> precedent there is for bindings etc.
>
Yep, I'm not entirely sure that the SPI framework can handle multiple
clients on the same CS.
The reason why we created device-addr is that the chip supports that and
may have hardcoded chip address from factory.
The chip address is also part of the protocol so we have to specify it.
> >
> > > Signed-off-by: Marcus Folkesson <marcus.folkesson@xxxxxxxxx>
> > > Signed-off-by: Kent Gustavsson <kent@xxxxxxxxxx>
> > > ---
> > > drivers/iio/adc/Kconfig | 10 ++
> > > drivers/iio/adc/Makefile | 1 +
> > > drivers/iio/adc/mcp3911.c | 444 ++++++++++++++++++++++++++++++++++++++++++++++
> > > 3 files changed, 455 insertions(+)
> > > create mode 100644 drivers/iio/adc/mcp3911.c
> > >
> > > diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
> > > index 15606f237480..f9a41fa96fcc 100644
> > > --- a/drivers/iio/adc/Kconfig
> > > +++ b/drivers/iio/adc/Kconfig
> > > @@ -501,6 +501,16 @@ config MCP3422
> > > This driver can also be built as a module. If so, the module will be
> > > called mcp3422.
> > >
> > > +config MCP3911
> > > + tristate "Microchip Technology MCP3911 driver"
> > > + depends on SPI
> > > + help
> > > + Say yes here to build support for Microchip Technology's MCP3911
> > > + analog to digital converter.
> > > +
> > > + This driver can also be built as a module. If so, the module will be
> > > + called mcp3911.
> > > +
> > > config MEDIATEK_MT6577_AUXADC
> > > tristate "MediaTek AUXADC driver"
> > > depends on ARCH_MEDIATEK || COMPILE_TEST
> > > diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
> > > index 28a9423997f3..3cfebfff7d26 100644
> > > --- a/drivers/iio/adc/Makefile
> > > +++ b/drivers/iio/adc/Makefile
> > > @@ -47,6 +47,7 @@ obj-$(CONFIG_MAX1363) += max1363.o
> > > obj-$(CONFIG_MAX9611) += max9611.o
> > > obj-$(CONFIG_MCP320X) += mcp320x.o
> > > obj-$(CONFIG_MCP3422) += mcp3422.o
> > > +obj-$(CONFIG_MCP3911) += mcp3911.o
> > > obj-$(CONFIG_MEDIATEK_MT6577_AUXADC) += mt6577_auxadc.o
> > > obj-$(CONFIG_MEN_Z188_ADC) += men_z188_adc.o
> > > obj-$(CONFIG_MESON_SARADC) += meson_saradc.o
> > > diff --git a/drivers/iio/adc/mcp3911.c b/drivers/iio/adc/mcp3911.c
> > > new file mode 100644
> > > index 000000000000..be74cb15827b
> > > --- /dev/null
> > > +++ b/drivers/iio/adc/mcp3911.c
> > > @@ -0,0 +1,444 @@
> > > +// SPDX-License-Identifier: GPL-2.0
> > > +/*
> > > + * Driver for Microchip MCP3911, Two-channel Analog Front End
> > > + *
> > > + * Copyright (C) 2018 Marcus Folkesson <marcus.folkesson@xxxxxxxxx>
> > > + * Copyright (C) 2018 Kent Gustavsson <kent@xxxxxxxxxx>
> > > + *
>
> No need for blank line here.
>
Ok
> > > + */
> > > +
> > > +#include <linux/delay.h>
> > > +#include <linux/err.h>
> > > +#include <linux/iio/iio.h>
> > > +#include <linux/module.h>
> > > +#include <linux/regulator/consumer.h>
> > > +#include <linux/spi/spi.h>
> > > +
> > > +#define MCP3911_REG_CHANNEL0 0x00
> > > +#define MCP3911_REG_CHANNEL1 0x03
> > > +#define MCP3911_REG_MOD 0x06
> > > +#define MCP3911_REG_PHASE 0x07
> > > +
> > > +#define MCP3911_REG_GAIN 0x09
> > > +#define MCP3911_GAIN_MASK(ch) (0x7 << 3*ch)
> >
> > space around * operator, maybe parenthesis around variable, i.e
> > (0x07 << (3 * (ch)))
> >
> > > +#define MCP3911_GAIN_VAL(ch, val) ((val << 3*ch) & MCP3911_GAIN_MASK(ch))
> > > +
> > > +#define MCP3911_REG_STATUSCOM 0x0a
> > > +#define MCP3911_STATUSCOM_CH1_24WIDTH BIT(4)
> > > +#define MCP3911_STATUSCOM_CH0_24WIDTH BIT(3)
> > > +#define MCP3911_STATUSCOM_EN_OFFCAL BIT(2)
> > > +#define MCP3911_STATUSCOM_EN_GAINCAL BIT(1)
> > > +
> > > +#define MCP3911_REG_CONFIG 0x0c
> > > +#define MCP3911_CONFIG_CLKEXT BIT(1)
> > > +#define MCP3911_CONFIG_VREFEXT BIT(2)
> > > +
> > > +#define MCP3911_REG_OFFCAL_CH0 0x0e
> > > +#define MCP3911_REG_GAINCAL_CH0 0x11
> > > +#define MCP3911_REG_OFFCAL_CH1 0x14
> > > +#define MCP3911_REG_GAINCAL_CH1 0x17
> > > +#define MCP3911_REG_VREFCAL 0x1a
> > > +
> > > +#define MCP3911_CHANNEL(x) (MCP3911_REG_CHANNEL0 + x * 3)
> > > +#define MCP3911_OFFCAL(x) (MCP3911_REG_OFFCAL_CH0 + x * 6)
> > > +#define MCP3911_GAINCAL(x) (MCP3911_REG_GAINCAL_CH0 + x * 6)
> > > +
> >
> > delete newline
> >
> > > +
> > > +/* Internal voltage reference in uV */
> > > +#define MCP3911_INT_VREF_UV 1200000
> > > +
> > > +#define REG_READ(reg, id) (((reg << 1) | (id << 5) | (1 << 0)) & 0xff)
> > > +#define REG_WRITE(reg, id) (((reg << 1) | (id << 5) | (0 << 0)) & 0xff)
> >
> > MCP3911_ prefix please
> > parenthesis around variables
> >
> > > +
> > > +#define MCP3911_NUM_CHANNELS 2
> > > +
> > > +
> > > +struct mcp3911 {
> > > + struct spi_device *spi;
> > > + struct device_node *np;
> > > + struct mutex lock;
> > > +
> > > + u32 gain[MCP3911_NUM_CHANNELS];
> > > + u32 width[MCP3911_NUM_CHANNELS];
> > > +
> > > + u32 dev_addr;
> > > + bool vrefext;
> > > + struct regulator *vref;
> > > +};
> > > +
> > > +static int mcp3911_read(struct mcp3911 *adc, u8 reg, u32 *val, u8 len)
> > > +{
> > > + int ret;
> > > +
> > > + reg = REG_READ(reg, adc->dev_addr);
> > > + ret = spi_write_then_read(adc->spi, ®, 1, val, len);
> > > + if (ret < 0)
> > > + return ret;
> > > +
> > > + *val <<= ((4-len)*8);
> >
> > space around - and * operator, here and elsewhere
> >
> > shouldn't the endiness conversion happen before the value is shifted?
> > (here and below)?
> >
> > > + be32_to_cpus(val);
> > > + dev_dbg(&adc->spi->dev, "Reading 0x%x from register 0x%x\n", *val,
> > > + reg>>1);
> > > + return ret;
> > > +}
> > > +
> > > +static int mcp3911_write(struct mcp3911 *adc, u8 reg, u32 val, u8 len)
> > > +{
> > > + dev_dbg(&adc->spi->dev, "Writing 0x%x to register 0x%x\n", val, reg);
> > > +
> > > + cpu_to_be32s(&val);
> > > + val >>= (3-len)*8;
> Hmm. It might be worth considering regmap here to handle all this stuff for
> you rather than re rolling the same stuff.
>
We were looking at regmap, but it does not seems to support registers of
different size.
This chip has register values of 8, 16 and 24 bits.
> > > + val |= REG_WRITE(reg, adc->dev_addr);
> > > +
> > > + return spi_write(adc->spi, &val, len+1);
> > > +}
> > > +
> > > +static int mcp3911_update(struct mcp3911 *adc, u8 reg, u32 mask,
> > > + u32 val, u8 len)
> > > +{
> > > + u32 tmp;
> > > + int ret;
> > > +
> > > + ret = mcp3911_read(adc, reg, &tmp, len);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + val &= mask;
> > > + val |= tmp & ~mask;
> > > + return mcp3911_write(adc, reg, val, len);
> > > +}
> > > +
> > > +static int mcp3911_get_hwgain(struct mcp3911 *adc, u8 channel, u32 *val)
> > > +{
> > > + int ret = mcp3911_read(adc, MCP3911_REG_GAIN, val, 1);
> > > +
> > > + if (ret)
> > > + return ret;
> > > +
> > > + *val >>= channel*3;
> > > + *val &= 0x07;
> > > + *val = (1 << *val);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int mcp3911_read_raw(struct iio_dev *indio_dev,
> > > + struct iio_chan_spec const *channel, int *val,
> > > + int *val2, long mask)
> > > +{
> > > + struct mcp3911 *adc = iio_priv(indio_dev);
> > > + int ret = -EINVAL;
> > > +
> > > + mutex_lock(&adc->lock);
> > > + switch (mask) {
> > > + case IIO_CHAN_INFO_RAW:
> > > + ret = mcp3911_read(adc,
> > > + MCP3911_CHANNEL(channel->channel), val, 3);
> > > + if (ret)
> > > + goto out;
> > > +
> > > + ret = IIO_VAL_INT;
> > > + break;
> > > +
> > > + case IIO_CHAN_INFO_OFFSET:
> > > + ret = mcp3911_read(adc,
> > > + MCP3911_OFFCAL(channel->channel), val, 3);
> > > + if (ret)
> > > + goto out;
> > > +
> > > + ret = IIO_VAL_INT;
> > > + break;
> > > +
> > > + case IIO_CHAN_INFO_HARDWAREGAIN:
> > > + ret = mcp3911_get_hwgain(adc, channel->channel, val);
>
> I'm not convinced it's useful to expose this as it right control for this
> is scale.
>
Hmm, all other drivers that are using HARDWAREGAIN (ina2xx-adc, stx104 +
a few more that are not ADC:s) are, what I can tell, exposing it.
But maybe it should'nt.
> > > + if (ret)
> > > + goto out;
> > > +
> > > + ret = IIO_VAL_INT;
> > > + break;
> > > +
> > > + case IIO_CHAN_INFO_SCALE:
> > > + if (adc->vrefext) {
> > > + ret = regulator_get_voltage(adc->vref);
> > > + if (ret < 0) {
> > > + dev_err(indio_dev->dev.parent,
> > > + "failed to get vref voltage:%d\n", ret);
> >
> > start message consistently with upper/lowercase
> > maybe space before :
> >
> > > + goto out;
> > > + }
> > > +
> > > + *val = ret / 1000;
> > > + } else {
> > > + *val = MCP3911_INT_VREF_UV;
> > > + }
> > > +
> > > + /* apply with gain value */
> > > + *val /= adc->gain[channel->channel];
> > > + *val2 = adc->width[channel->channel];
> > > +
> > > + ret = IIO_VAL_FRACTIONAL_LOG2;
> > > + break;
> > > + }
> > > +
> > > +out:
> > > + mutex_unlock(&adc->lock);
> > > +
> > > + return ret;
> > > +}
> > > +
> > > +static int mcp3911_write_raw(struct iio_dev *indio_dev,
> > > + struct iio_chan_spec const *channel, int val,
> > > + int val2, long mask)
> > > +{
> > > + struct mcp3911 *adc = iio_priv(indio_dev);
> > > + int ret = -EINVAL;
> > > +
> > > + mutex_lock(&adc->lock);
> > > + switch (mask) {
> > > + case IIO_CHAN_INFO_OFFSET:
> > > +
> >
> > val2 should probably be zero and checked?
> >
> > > + /* Write offset */
> > > + ret = mcp3911_write(adc, MCP3911_OFFCAL(channel->channel), val,
> > > + 3);
> > > + if (ret)
> > > + goto out;
> > > +
> > > + /* Enable offset*/
> > > + ret = mcp3911_update(adc, MCP3911_REG_STATUSCOM,
> > > + MCP3911_STATUSCOM_EN_OFFCAL,
> > > + MCP3911_STATUSCOM_EN_OFFCAL, 2);
> > > + if (ret)
> > > + goto out;
>
> We go there anyway so why bother with the goto?
>
Yep, the goto will be removed.
> > > +
> > > + break;
> > > +
> > > + case IIO_CHAN_INFO_HARDWAREGAIN:
>
> Default choice (by precedent) is to control variable gain
> front ends via the scale parameter. Hardware gain
> is not meant to have any 'visible' impact on the output
> value - most commonly used when the thing we are measuring
> is not amplitude of anything.
Hmm, Ok. I'm not sure I understand how hardware gain is supposed to work
then.
Maybe I just remove it.
>
> >
> > val2?
> >
> > > + if (!is_power_of_2(val) && val <= 32) {
> >
> > the check looks suspicious, maybe || val > 32
> >
> > > + ret = -EINVAL;
> > > + goto out;
> > > + }
> > > +
> > > + adc->gain[channel->channel] = val;
> > > +
> > > + val = ilog2(val);
> > > + ret = mcp3911_update(adc, MCP3911_REG_GAIN,
> > > + MCP3911_GAIN_MASK(channel->channel),
> > > + MCP3911_GAIN_VAL(channel->channel,
> > > + val), 1);
> > > + break;
> > > + }
> > > +
> > > +out:
> > > + mutex_unlock(&adc->lock);
> > > +
> > > + return ret;
> > > +}
> > > +
> > > +static const struct iio_chan_spec mcp3911_channels[] = {
> > > + {
> >
> > maybe use a MACRO(), e.g. MCP3911_CHANNEL(idx) ...
> >
> > > + .type = IIO_VOLTAGE,
> > > + .indexed = 1,
> > > + .channel = 0,
> > > + .address = MCP3911_REG_CHANNEL0,
> > > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
> > > + BIT(IIO_CHAN_INFO_OFFSET) |
> > > + BIT(IIO_CHAN_INFO_SCALE) |
> > > + BIT(IIO_CHAN_INFO_HARDWAREGAIN),
> > > + },
> > > + {
> > > + .type = IIO_VOLTAGE,
> > > + .indexed = 1,
> > > + .channel = 1,
> > > + .address = MCP3911_REG_CHANNEL1,
> > > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
> > > + BIT(IIO_CHAN_INFO_OFFSET) |
> > > + BIT(IIO_CHAN_INFO_SCALE) |
> > > + BIT(IIO_CHAN_INFO_HARDWAREGAIN),
> > > + },
> > > +};
> > > +
> > > +static const struct iio_info mcp3911_info = {
> > > + .read_raw = mcp3911_read_raw,
> > > + .write_raw = mcp3911_write_raw,
> > > +};
> > > +
> > > +static int mcp3911_config_of(struct mcp3911 *adc)
> > > +{
> > > + u32 configreg;
> > > + u32 statuscomreg;
> > > + int ret;
> > > +
> > > + of_property_read_u32(adc->np, "device-addr", &adc->dev_addr);
> This is 'interesting' - I wonder if there is any precedence for it.
>
I guess we still need it since the device may have a hardcoded (from
factory) address that we need to deal with.
> Mark,
> > > + if (adc->dev_addr > 3) {
> > > + dev_err(&adc->spi->dev,
> > > + "invalid device address (%i). Must be in range 0-3.\n",
> > > + adc->dev_addr);
> > > + return -EINVAL;
> > > + }
> > > + dev_dbg(&adc->spi->dev, "use device address %i\n", adc->dev_addr);
> > > +
> > > + ret = mcp3911_read(adc, MCP3911_REG_CONFIG, &configreg, 2);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + adc->vrefext = of_property_read_bool(adc->np, "external-vref");
>
> Why not just use the presence or lack of a regulator being supplied to indicate
> this? Use the regulator_get_optional functionality to avoid getting a stub
> regulator if you need to know there isn't one there to connect.
> Here you need the _optional form.
Ah!
I wanted it to work that way, but got the dummy regulator when no
regulator was provided.
So _optional is the thing.
Thanks!
>
> > > + if (adc->vrefext) {
> > > + dev_dbg(&adc->spi->dev, "use external voltage reference\n");
> > > + configreg |= MCP3911_CONFIG_VREFEXT;
> > > +
> > > + } else {
> > > + dev_dbg(&adc->spi->dev, "use internal voltage reference (1.2V)\n");
> > > + configreg &= ~MCP3911_CONFIG_VREFEXT;
> > > + }
> > > +
> > > + if (of_property_read_bool(adc->np, "external-clock")) {
> > > + dev_dbg(&adc->spi->dev, "use external clock as clocksource\n");
> > > + configreg |= MCP3911_CONFIG_CLKEXT;
> > > + } else {
> > > + dev_dbg(&adc->spi->dev, "use crystal oscillator as clocksource\n");
> > > + configreg &= ~MCP3911_CONFIG_CLKEXT;
> > > + }
>
> Sort of feels like this should be handled a bit like the regulator.
> The kernel has bindings and software support for clocks. Would be nice
> to use them.
>
Indeed. I will go for the clocks instead.
> > > +
> > > + ret = mcp3911_write(adc, MCP3911_REG_CONFIG, configreg, 2);
> > > + if (ret)
> > > + return ret;
> > > +
> > > +
> > > + ret = mcp3911_read(adc, MCP3911_REG_STATUSCOM, &statuscomreg, 2);
> > > + if (ret)
> > > + return ret;
> > > +
> >
> > no duplicate newlines (here and elsewhere)
> >
> > > +
> > > + of_property_read_u32(adc->np, "ch0-width", &adc->width[0]);
> > > + switch (adc->width[0]) {
> > > + case 24:
> > > + statuscomreg &= ~MCP3911_STATUSCOM_CH0_24WIDTH;
> > > + dev_dbg(&adc->spi->dev, "set channel 0 into 24bit mode\n");
> > > + break;
> > > + case 16:
> > > + statuscomreg |= MCP3911_STATUSCOM_CH0_24WIDTH;
> > > + dev_dbg(&adc->spi->dev, "set channel 0 into 16bit mode\n");
> > > + break;
> > > + default:
> > > + adc->width[0] = 24;
> > > + dev_info(&adc->spi->dev, "invalid width for channel 0. Use 24bit.\n");
> > > + break;
> > > + }
> This feels like something that isn't really a dt choice, as it's not down to
> wiring but rather down to precision desired.
You are right. I will remove them and stick to 24bit width.
>
> Now variable resolution isn't something IIO has traditionally dealt
> with very well - particularly as it causes problems when we add in
> buffered interfaces (as it changes the data layout etc).
>
> > > +
> > > + of_property_read_u32(adc->np, "ch1-width", &adc->width[1]);
> > > + switch (adc->width[1]) {
> > > + case 24:
> > > + statuscomreg &= ~MCP3911_STATUSCOM_CH1_24WIDTH;
> > > + dev_dbg(&adc->spi->dev, "set channel 1 into 24bit mode\n");
> > > + break;
> > > + case 16:
> > > + statuscomreg |= MCP3911_STATUSCOM_CH1_24WIDTH;
> > > + dev_dbg(&adc->spi->dev, "set channel 1 into 16bit mode\n");
> > > + break;
> > > + default:
> > > + adc->width[1] = 24;
> > > + dev_info(&adc->spi->dev, "invalid width for channel 1. Use 24bit.\n");
> > > + break;
> > > + }
> > > +
> > > + return mcp3911_write(adc, MCP3911_REG_STATUSCOM, statuscomreg, 2);
> > > +}
> > > +
> > > +static int mcp3911_probe(struct spi_device *spi)
> > > +{
> > > + struct iio_dev *indio_dev;
> > > + struct mcp3911 *adc;
> > > + int ret;
> > > +
> > > + indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*adc));
> > > + if (!indio_dev)
> > > + return -ENOMEM;
> > > +
> > > + adc = iio_priv(indio_dev);
> > > + adc->spi = spi;
> > > + adc->np = spi->dev.of_node;
>
> np is is rather unusual naming. Why not of_node?
> Also, why do we need to keep a copy of this?
I guess the drivers I was looking at called it 'np'.
However, I guess there is no need to keep a copy of it.
I will remove it.
>
> > > +
> > > + ret = mcp3911_config_of(adc);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + if (adc->vrefext) {
> > > + adc->vref = devm_regulator_get(&adc->spi->dev, "vref");
>
> As I mention above, use devm_regulator_get_optional if you need
> to be able to do something different dependent on whether the regulator
> is actually there, if not just use devm_regulator_get and without
> any if (adc->vrefext) and you'll get a 'fake' regulator which you can
> enable and disable without it doing anything.
Got it. Thanks!
>
> > > + if (IS_ERR(adc->vref))
> > > + return PTR_ERR(adc->vref);
> > > +
> > > + ret = regulator_enable(adc->vref);
> > > + if (ret < 0)
> > > + return ret;
> > > + }
> > > +
> > > + /* Store gain values to better calculate scale values */
> > > + mcp3911_get_hwgain(adc, 0, &adc->gain[0]);
> > > + mcp3911_get_hwgain(adc, 1, &adc->gain[1]);
> > > +
> > > + indio_dev->dev.parent = &spi->dev;
> > > + indio_dev->dev.of_node = spi->dev.of_node;
> > > + indio_dev->name = spi_get_device_id(spi)->name;
> > > + indio_dev->modes = INDIO_DIRECT_MODE;
> > > + indio_dev->info = &mcp3911_info;
> > > + spi_set_drvdata(spi, indio_dev);
> > > +
> > > + indio_dev->channels = mcp3911_channels;
> > > + indio_dev->num_channels = ARRAY_SIZE(mcp3911_channels);
> > > +
> > > + mutex_init(&adc->lock);
> > > +
> > > + ret = iio_device_register(indio_dev);
> > > + if (ret)
> > > + goto reg_disable;
> > > +
> > > + return ret;
> > > +
> > > +reg_disable:
> > > + if (adc->vref)
> > > + regulator_disable(adc->vref);
> > > +
> > > + return ret;
> > > +}
> > > +
> > > +static int mcp3911_remove(struct spi_device *spi)
> > > +{
> > > + struct iio_dev *indio_dev = spi_get_drvdata(spi);
> > > + struct mcp3911 *adc = iio_priv(indio_dev);
> > > +
> > > + iio_device_unregister(indio_dev);
> > > +
> > > + if (adc->vref)
> > > + regulator_disable(adc->vref);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +#if defined(CONFIG_OF)
> > > +static const struct of_device_id mcp3911_dt_ids[] = {
> > > + { .compatible = "microchip,mcp3911" },
> > > + { }
> > > +};
> > > +MODULE_DEVICE_TABLE(of, mcp3911_dt_ids);
> > > +#endif
> > > +
> > > +static const struct spi_device_id mcp3911_id[] = {
> > > + { "mcp3911", 0 },
> > > + { }
> > > +};
> > > +MODULE_DEVICE_TABLE(spi, mcp3911_id);
> > > +
> > > +static struct spi_driver mcp3911_driver = {
> > > + .driver = {
> > > + .name = "mcp3911",
> > > + .of_match_table = of_match_ptr(mcp3911_dt_ids),
> > > + },
> > > + .probe = mcp3911_probe,
> > > + .remove = mcp3911_remove,
> > > + .id_table = mcp3911_id,
> > > +};
> > > +module_spi_driver(mcp3911_driver);
> > > +
> > > +MODULE_AUTHOR("Marcus Folkesson <marcus.folkesson@xxxxxxxxx>");
> > > +MODULE_AUTHOR("Kent Gustavsson <kent@xxxxxxxxxx>");
> > > +MODULE_DESCRIPTION("Microchip Technology MCP3911");
> > > +MODULE_LICENSE("GPL v2");
> > >
> >
>
Best regards
Marcus Folkesson
Attachment:
signature.asc
Description: PGP signature