Re: [PATCH 3/3] arm64: allwinner: dts: h6: add Wi-Fi support for Pine H64 model A/B

From: Chen-Yu Tsai
Date: Mon Jul 23 2018 - 22:22:32 EST


On Tue, Jul 24, 2018 at 9:15 AM, Icenowy Zheng <icenowy@xxxxxxx> wrote:
> The Pine H64 model A has a Wi-Fi module connector and the model B has an
> on-board RTL8723BS Wi-Fi module.
>
> Add support for them. For model A, as it's not defaultly present, keep
> it disabled now.

Nope. Pine64 actually has two WiFi/BT modules. And they require different
device tree snippets for both the WiFi and BT side. This is better resolved
with device tree overlays.

I have both, though I've yet found time to work on them.

ChenYu

> Signed-off-by: Icenowy Zheng <icenowy@xxxxxxx>
> ---
> .../allwinner/sun50i-h6-pine-h64-model-b.dts | 8 +++++
> .../boot/dts/allwinner/sun50i-h6-pine-h64.dts | 29 +++++++++++++++++++
> 2 files changed, 37 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64-model-b.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64-model-b.dts
> index d0fcc25efb00..d0f775613c9b 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64-model-b.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64-model-b.dts
> @@ -18,3 +18,11 @@
> };
> };
> };
> +
> +&mmc1 {
> + status = "okay";
> +};
> +
> +&wifi_pwrseq {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts
> index a85867f8b684..75db6d4139bf 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts
> @@ -40,6 +40,12 @@
> gpios = <&r_pio 0 7 GPIO_ACTIVE_HIGH>; /* PL7 */
> };
> };
> +
> + wifi_pwrseq: wifi_pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PL2 */
> + status = "disabled";
> + };
> };
>
> &mmc0 {
> @@ -50,6 +56,17 @@
> status = "okay";
> };
>
> +&mmc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc1_pins>;
> + vmmc-supply = <&reg_cldo2>;
> + vqmmc-supply = <&reg_bldo2>;
> + mmc-pwrseq = <&wifi_pwrseq>;
> + bus-width = <4>;
> + non-removable;
> + status = "disabled";
> +};
> +
> &mmc2 {
> pinctrl-names = "default";
> pinctrl-0 = <&mmc2_pins>;
> @@ -128,12 +145,24 @@
> };
>
> reg_cldo2: cldo2 {
> + /*
> + * This regulator is connected with CLDO3.
> + * Before the kernel can support synchronized
> + * enable of coupled regulators, keep them
> + * both always on as a ugly hack.
> + */
> + regulator-always-on;
> regulator-min-microvolt = <3300000>;
> regulator-max-microvolt = <3300000>;
> regulator-name = "vcc-wifi-1";
> };
>
> reg_cldo3: cldo3 {
> + /*
> + * This regulator is connected with CLDO2.
> + * See the comments for CLDO2.
> + */
> + regulator-always-on;
> regulator-min-microvolt = <3300000>;
> regulator-max-microvolt = <3300000>;
> regulator-name = "vcc-wifi-2";
> --
> 2.18.0
>