Re: [PATCH v3 1/3] Input: edt-ft5x06 - Add support for regulator

[MylÃne Josserand]

Hello,

Thank you for your review.

On Thu, 19 Jul 2018 00:46:45 +0200
OndÅej Jirman <megous@xxxxxxxxxx> wrote:

> Hello MylÃne,
> 
> On Wed, Jul 18, 2018 at 08:27:17PM +0200, MylÃne Josserand wrote:
> > Add the support of regulator to use it as VCC source.
> > 
> > Signed-off-by: MylÃne Josserand <mylene.josserand@xxxxxxxxxxx>
> > ---
> >  .../bindings/input/touchscreen/edt-ft5x06.txt      |  1 +
> >  drivers/input/touchscreen/edt-ft5x06.c             | 29 ++++++++++++++++++++++
> >  2 files changed, 30 insertions(+)
> > 
> > diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> > index 025cf8c9324a..48e975b9c1aa 100644
> > --- a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> > +++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> > @@ -30,6 +30,7 @@ Required properties:
> >  Optional properties:
> >   - reset-gpios: GPIO specification for the RESET input
> >   - wake-gpios:  GPIO specification for the WAKE input
> > + - vcc-supply:  Regulator that supplies the touchscreen
> >  
> >   - pinctrl-names: should be "default"
> >   - pinctrl-0:   a phandle pointing to the pin settings for the
> > diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
> > index 1e18ca0d1b4e..aa94494b06b5 100644
> > --- a/drivers/input/touchscreen/edt-ft5x06.c
> > +++ b/drivers/input/touchscreen/edt-ft5x06.c
> > @@ -39,6 +39,7 @@
> >  #include <linux/input/mt.h>
> >  #include <linux/input/touchscreen.h>
> >  #include <linux/of_device.h>
> > +#include <linux/regulator/consumer.h>
> >  
> >  #define WORK_REGISTER_THRESHOLD		0x00
> >  #define WORK_REGISTER_REPORT_RATE	0x08
> > @@ -91,6 +92,7 @@ struct edt_ft5x06_ts_data {
> >  	struct touchscreen_properties prop;
> >  	u16 num_x;
> >  	u16 num_y;
> > +	struct regulator *vcc;
> >  
> >  	struct gpio_desc *reset_gpio;
> >  	struct gpio_desc *wake_gpio;
> > @@ -991,6 +993,22 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
> >  
> >  	tsdata->max_support_points = chip_data->max_support_points;
> >  
> > +	tsdata->vcc = devm_regulator_get(&client->dev, "vcc");
> > +	if (IS_ERR(tsdata->vcc)) {
> > +		error = PTR_ERR(tsdata->vcc);
> > +		if (error != -EPROBE_DEFER)
> > +			dev_err(&client->dev, "failed to request regulator: %d\n",
> > +				error);
> > +		return error;
> > +	}
> > +
> > +	error = regulator_enable(tsdata->vcc);
> > +	if (error < 0) {
> > +		dev_err(&client->dev, "failed to enable vcc: %d\n",
> > +			error);
> > +		return error;
> > +	}
> > +
> >  	tsdata->reset_gpio = devm_gpiod_get_optional(&client->dev,
> >  						     "reset", GPIOD_OUT_HIGH);
> >  	if (IS_ERR(tsdata->reset_gpio)) {
> > @@ -1120,20 +1138,31 @@ static int edt_ft5x06_ts_remove(struct i2c_client *client)
> >  static int __maybe_unused edt_ft5x06_ts_suspend(struct device *dev)
> >  {
> >  	struct i2c_client *client = to_i2c_client(dev);
> > +	struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
> >  
> >  	if (device_may_wakeup(dev))
> >  		enable_irq_wake(client->irq);
> >  
> > +	regulator_disable(tsdata->vcc);
> > +  
> 
> How will the touchscreen wakeup the system with interrupt if you power it off
> on suspend? Perhaps guard this with device_may_wakeup() too? 

True, thank you for pointing it out.

> 
> >  	return 0;
> >  }
> >  
> >  static int __maybe_unused edt_ft5x06_ts_resume(struct device *dev)
> >  {
> >  	struct i2c_client *client = to_i2c_client(dev);
> > +	struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
> > +	int ret;
> >  
> >  	if (device_may_wakeup(dev))
> >  		disable_irq_wake(client->irq);
> >  
> > +	ret = regulator_enable(tsdata->vcc);
> > +	if (ret < 0) {
> > +		dev_err(dev, "failed to enable vcc: %d\n", ret);
> > +		return ret;
> > +	}
> > +  
> 
> Ditto.

ack

> 
> Regards,
>   o.
> 
> >  	return 0;
> >  }
> >  
> > -- 
> > 2.11.0
> > 
> > 
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel  


Best regards,

-- 
MylÃne Josserand, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
https://bootlin.com