[PATCH v8 1/5] phy: Update PHY power control sequence

From: Can Guo
Date: Tue Jul 31 2018 - 06:09:32 EST


All PHYs should be powered on before register configuration starts. And
only PCIe PHYs need an extra power control before deasserts reset state.

Signed-off-by: Can Guo <cang@xxxxxxxxxxxxxx>
Reviewed-by: Manu Gautam <mgautam@xxxxxxxxxxxxxx>
Reviewed-by: Vivek Gautam <vivek.gautam@xxxxxxxxxxxxxx>
Reviewed-by: Evan Green <evgreen@xxxxxxxxxxxx>
---
drivers/phy/qualcomm/phy-qcom-qmp.c | 19 ++++++++++++-------
1 file changed, 12 insertions(+), 7 deletions(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index 97ef942..ccb8578 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -935,10 +935,12 @@ static void qcom_qmp_phy_configure(void __iomem *base,
}
}

-static int qcom_qmp_phy_com_init(struct qcom_qmp *qmp)
+static int qcom_qmp_phy_com_init(struct qmp_phy *qphy)
{
+ struct qcom_qmp *qmp = qphy->qmp;
const struct qmp_phy_cfg *cfg = qmp->cfg;
void __iomem *serdes = qmp->serdes;
+ void __iomem *pcs = qphy->pcs;
void __iomem *dp_com = qmp->dp_com;
int ret, i;

@@ -979,10 +981,6 @@ static int qcom_qmp_phy_com_init(struct qcom_qmp *qmp)
goto err_rst;
}

- if (cfg->has_phy_com_ctrl)
- qphy_setbits(serdes, cfg->regs[QPHY_COM_POWER_DOWN_CONTROL],
- SW_PWRDN);
-
if (cfg->has_phy_dp_com_ctrl) {
qphy_setbits(dp_com, QPHY_V3_DP_COM_POWER_DOWN_CTRL,
SW_PWRDN);
@@ -1000,6 +998,12 @@ static int qcom_qmp_phy_com_init(struct qcom_qmp *qmp)
SW_USB3PHY_RESET_MUX | SW_USB3PHY_RESET);
}

+ if (cfg->has_phy_com_ctrl)
+ qphy_setbits(serdes, cfg->regs[QPHY_COM_POWER_DOWN_CONTROL],
+ SW_PWRDN);
+ else
+ qphy_setbits(pcs, QPHY_POWER_DOWN_CONTROL, cfg->pwrdn_ctrl);
+
/* Serdes configuration */
qcom_qmp_phy_configure(serdes, cfg->regs, cfg->serdes_tbl,
cfg->serdes_tbl_num);
@@ -1090,7 +1094,7 @@ static int qcom_qmp_phy_init(struct phy *phy)

dev_vdbg(qmp->dev, "Initializing QMP phy\n");

- ret = qcom_qmp_phy_com_init(qmp);
+ ret = qcom_qmp_phy_com_init(qphy);
if (ret)
return ret;

@@ -1127,7 +1131,8 @@ static int qcom_qmp_phy_init(struct phy *phy)
* Pull out PHY from POWER DOWN state.
* This is active low enable signal to power-down PHY.
*/
- qphy_setbits(pcs, QPHY_POWER_DOWN_CONTROL, cfg->pwrdn_ctrl);
+ if(cfg->type == PHY_TYPE_PCIE)
+ qphy_setbits(pcs, QPHY_POWER_DOWN_CONTROL, cfg->pwrdn_ctrl);

if (cfg->has_pwrdn_delay)
usleep_range(cfg->pwrdn_delay_min, cfg->pwrdn_delay_max);
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project