Re: [PATCH] lightnvm: pblk: recover chunk state on 1.2 devices
From: Matias BjÃrling
Date: Fri Aug 03 2018 - 08:31:03 EST
On 08/03/2018 02:02 PM, Javier Gonzalez wrote:
On 3 Aug 2018, at 13.57, Matias BjÃrling <mb@xxxxxxxxxxx> wrote:
On 07/24/2018 09:54 AM, Javier Gonzalez wrote:
On 29 Jun 2018, at 13.28, Matias BjÃrling <mb@xxxxxxxxxxx> wrote:
On 06/29/2018 01:22 PM, Javier Gonzalez wrote:
On 29 Jun 2018, at 13.14, Matias BjÃrling <mb@xxxxxxxxxxx> wrote:
On 06/28/2018 11:12 AM, Javier GonzÃlez wrote:
The Open-Channel 1.2 spec does not define a mechanism for the host to
recover the block (chunk) state. As a consequence, a newly format device
will need to reconstruct the state. Currently, pblk assumes that blocks
are not erased, which might cause double-erases in case that the device
does not protect itself against them (which is not specified in the spec
either).
It should not be specified in the spec. It is up to the device to handle
double erases and not do it.
This patch, reconstructs the state based on read errors. If the first
sector of a block returns and empty page (NVM_RSP_ERR_EMPTYPAGE), then
the block s marked free, i.e., erased and ready to be used
(NVM_CHK_ST_FREE). Otherwise, the block is marked as closed
(NVM_CHK_ST_CLOSED). Note that even if a block is open and not fully
written, it has to be erased in order to be used again.
Should we extend it to do the scan, and update the write pointer as
well? I think this kind of feature already is baked into pblk?
This is already in place: we scan until empty page and take it from
there. This patch is only for the case in which we start a pblk instance
form scratch. On a device already owned by pblk, we would not have the
problem we are trying to solve here because we know the state.
Agree. What I meant was that when we anyway are recovering the state,
we could just as well update ->wp and set to NVM_CHK_ST_OPEN and so
forth for the initialization phase.
In 1.2 the use of chunk metadata is purely fictional. We respect the
chunk state machine as we transition lines, but all the write pointers
are ignored. Instead, we use the line bitmap to point to the next
writable entry. This is BTW the same way we it in open lines on 2.0 too.
Now I understand where you are coming from. I had the understanding
that we where using the write pointer now that we moved to 2.0,
looking through the code, that wasn't the case. :) Which means that
pblk doesn't work with a devices that implements 2.0. Yikes... I knew
I had forgot a detail when support was added into pblk.
I think you misunderstood; pblk does support 2.0 devices. What happens
is that we transform the per chunk WP in 2.0 into the line bitmap to
simplify the lookup. The point being that we do not need to create a
fictional chunk for 1.2 devices since we do the translation to the
bitmap directly. Does this make sense?
The chunk->wp isn't used anywhere. So it can't take wp into account. It
uses the EMPTYPAGE marker from 1.2 instead. See pblk-core and
pblk-recovery.
There are no empty sector marker in the 2.0 spec, since it uses the
write pointer to know where it is in the chunk. So there is a bit of
work to do there.
Yes. And for 2.0 devices we go and look at the WP, but for 1.2 devices we
need to scan.
Since this properly is a bit more work to do, I'll look into it after FMS.
Look the comments above. All we need for 2.0 support is in place. We can
talk about it f2f.
I'm also moving the explicit coding of 1.2/2.0 chunk / bad block
fixing into core, so pblk can be simplfied, and doesn't have to think
to manage each version separately.
Good. I have a patch I was expecting to send after FMS for moving chunk
/ bad block out of pblk for the same reason. If you're doing the same
thing I can stop looking into it...
I am, will post when done.
Chunk metadata is only used to setup the bitmaps on init/recovery. From
here on, we use the bitmap to find the next writable sector, without
worrying about the specific per-chunk write pointer. Thus, updating
chunk metadata here has no effect.
Does this make sense to you?
Javier