[PATCH v1 4/5] arm64: dts: mt7622: add bananapi BPI-R64 board

From: Ryder Lee
Date: Sat Aug 18 2018 - 12:03:35 EST

Add support for the bananapi R64 (BPI-R64) development board from
BIPAI KEJI. Detailed hardware information for BPI-R64 which could be
found on http://wiki.banana-pi.org/Banana_Pi_BPI-R64

Signed-off-by: Ryder Lee <ryder.lee@xxxxxxxxxxxx>
---
changes since v1:
- add missing sata nodes.
- fix pinctrl-0 for pcie@1,0.
- switch goio keys from polling mode to intterupt mode.
- add gpio-led nodes.
---
arch/arm64/boot/dts/mediatek/Makefile | 1 +
.../boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts | 530 +++++++++++++++++++++
2 files changed, 531 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts

diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 5b7fd6a..e8f952f 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -5,4 +5,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6795-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts
new file mode 100644
index 0000000..5d6005c
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts
@@ -0,0 +1,530 @@
+/*
+ * Copyright (c) 2018 MediaTek Inc.
+ * Author: Ryder Lee <ryder.lee@xxxxxxxxxxxx>
+ *
+ * SPDX-License-Identifier: (GPL-2.0 OR MIT)
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+#include "mt7622.dtsi"
+#include "mt6380.dtsi"
+
+/ {
+ model = "Bananapi BPI-R64";
+ compatible = "bananapi,bpi-r64", "mediatek,mt7622";
+
+ chosen {
+ bootargs = "earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n1 swiotlb=512";
+ };
+
+ cpus {
+ cpu@0 {
+ proc-supply = <&mt6380_vcpu_reg>;
+ sram-supply = <&mt6380_vm_reg>;
+ };
+
+ cpu@1 {
+ proc-supply = <&mt6380_vcpu_reg>;
+ sram-supply = <&mt6380_vm_reg>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ factory {
+ label = "factory";
+ linux,code = <BTN_0>;
+ gpios = <&pio 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ wps {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&pio 102 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ green {
+ label = "bpi-r64:pio:green";
+ gpios = <&pio 89 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ red {
+ label = "bpi-r64:pio:red";
+ gpios = <&pio 88 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+
+ memory {
+ reg = <0 0x40000000 0 0x40000000>;
+ };
+
+ reg_1p8v: regulator-1p8v {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_5v: regulator-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+};
+
+&bch {
+ status = "disabled";
+};
+
+&btif {
+ status = "okay";
+};
+
+&cir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&irrx_pins>;
+ status = "okay";
+};
+
+&eth {
+ pinctrl-names = "default";
+ pinctrl-0 = <&eth_pins>;
+ status = "okay";
+
+ gmac1: mac@1 {
+ compatible = "mediatek,eth-mac";
+ reg = <1>;
+ phy-handle = <&phy5>;
+ };
+
+ mdio-bus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy5: ethernet-phy@5 {
+ reg = <5>;
+ phy-mode = "sgmii";
+ };
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&emmc_pins_default>;
+ pinctrl-1 = <&emmc_pins_uhs>;
+ status = "okay";
+ bus-width = <8>;
+ max-frequency = <50000000>;
+ cap-mmc-highspeed;
+ mmc-hs200-1_8v;
+ vmmc-supply = <&reg_3p3v>;
+ vqmmc-supply = <&reg_1p8v>;
+ assigned-clocks = <&topckgen CLK_TOP_MSDC30_0_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIV48M>;
+ non-removable;
+};
+
+&mmc1 {
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&sd0_pins_default>;
+ pinctrl-1 = <&sd0_pins_uhs>;
+ status = "okay";
+ bus-width = <4>;
+ max-frequency = <50000000>;
+ cap-sd-highspeed;
+ r_smpl = <1>;
+ cd-gpios = <&pio 81 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&reg_3p3v>;
+ vqmmc-supply = <&reg_3p3v>;
+ assigned-clocks = <&topckgen CLK_TOP_MSDC30_1_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIV48M>;
+};
+
+&nandc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&parallel_nand_pins>;
+ status = "disabled";
+};
+
+&nor_flash {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_nor_pins>;
+ status = "disabled";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ };
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie0_pins>, <&pcie1_pins>;
+ status = "okay";
+
+ pcie@0,0 {
+ status = "okay";
+ };
+
+ pcie@1,0 {
+ status = "okay";
+ };
+};
+
+&pio {
+ /* Attention: GPIO 90 is used to switch between PCIe@1,0 and
+ * SATA functions. i.e. output-high: PCIe, output-low: SATA
+ */
+ asm_sel {
+ gpio-hog;
+ gpios = <90 GPIO_ACTIVE_HIGH>;
+ output-high;
+ };
+
+ /* eMMC is shared pin with parallel NAND */
+ emmc_pins_default: emmc-pins-default {
+ mux {
+ function = "emmc", "emmc_rst";
+ groups = "emmc";
+ };
+
+ /* "NDL0","NDL1","NDL2","NDL3","NDL4","NDL5","NDL6","NDL7",
+ * "NRB","NCLE" pins are used as DAT0,DAT1,DAT2,DAT3,DAT4,
+ * DAT5,DAT6,DAT7,CMD,CLK for eMMC respectively
+ */
+ conf-cmd-dat {
+ pins = "NDL0", "NDL1", "NDL2",
+ "NDL3", "NDL4", "NDL5",
+ "NDL6", "NDL7", "NRB";
+ input-enable;
+ bias-pull-up;
+ };
+
+ conf-clk {
+ pins = "NCLE";
+ bias-pull-down;
+ };
+ };
+
+ emmc_pins_uhs: emmc-pins-uhs {
+ mux {
+ function = "emmc";
+ groups = "emmc";
+ };
+
+ conf-cmd-dat {
+ pins = "NDL0", "NDL1", "NDL2",
+ "NDL3", "NDL4", "NDL5",
+ "NDL6", "NDL7", "NRB";
+ input-enable;
+ drive-strength = <4>;
+ bias-pull-up;
+ };
+
+ conf-clk {
+ pins = "NCLE";
+ drive-strength = <4>;
+ bias-pull-down;
+ };
+ };
+
+ eth_pins: eth-pins {
+ mux {
+ function = "eth";
+ groups = "mdc_mdio", "rgmii_via_gmac2";
+ };
+ };
+
+ i2c1_pins: i2c1-pins {
+ mux {
+ function = "i2c";
+ groups = "i2c1_0";
+ };
+ };
+
+ i2c2_pins: i2c2-pins {
+ mux {
+ function = "i2c";
+ groups = "i2c2_0";
+ };
+ };
+
+ i2s1_pins: i2s1-pins {
+ mux {
+ function = "i2s";
+ groups = "i2s_out_mclk_bclk_ws",
+ "i2s1_in_data",
+ "i2s1_out_data";
+ };
+
+ conf {
+ pins = "I2S1_IN", "I2S1_OUT", "I2S_BCLK",
+ "I2S_WS", "I2S_MCLK";
+ drive-strength = <12>;
+ bias-pull-down;
+ };
+ };
+
+ irrx_pins: irrx-pins {
+ mux {
+ function = "ir";
+ groups = "ir_1_rx";
+ };
+ };
+
+ irtx_pins: irtx-pins {
+ mux {
+ function = "ir";
+ groups = "ir_1_tx";
+ };
+ };
+
+ /* Parallel nand is shared pin with eMMC */
+ parallel_nand_pins: parallel-nand-pins {
+ mux {
+ function = "flash";
+ groups = "par_nand";
+ };
+ };
+
+ pcie0_pins: pcie0-pins {
+ mux {
+ function = "pcie";
+ groups = "pcie0_pad_perst",
+ "pcie0_1_waken",
+ "pcie0_1_clkreq";
+ };
+ };
+
+ pcie1_pins: pcie1-pins {
+ mux {
+ function = "pcie";
+ groups = "pcie1_pad_perst",
+ "pcie1_0_waken",
+ "pcie1_0_clkreq";
+ };
+ };
+
+ pmic_bus_pins: pmic-bus-pins {
+ mux {
+ function = "pmic";
+ groups = "pmic_bus";
+ };
+ };
+
+ pwm7_pins: pwm1-2-pins {
+ mux {
+ function = "pwm";
+ groups = "pwm_ch7_2";
+ };
+ };
+
+ wled_pins: wled-pins {
+ mux {
+ function = "led";
+ groups = "wled";
+ };
+ };
+
+ sd0_pins_default: sd0-pins-default {
+ mux {
+ function = "sd";
+ groups = "sd_0";
+ };
+
+ /* "I2S2_OUT, "I2S4_IN"", "I2S3_IN", "I2S2_IN",
+ * "I2S4_OUT", "I2S3_OUT" are used as DAT0, DAT1,
+ * DAT2, DAT3, CMD, CLK for SD respectively.
+ */
+ conf-cmd-data {
+ pins = "I2S2_OUT", "I2S4_IN", "I2S3_IN",
+ "I2S2_IN","I2S4_OUT";
+ input-enable;
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ conf-clk {
+ pins = "I2S3_OUT";
+ drive-strength = <12>;
+ bias-pull-down;
+ };
+ conf-cd {
+ pins = "TXD3";
+ bias-pull-up;
+ };
+ };
+
+ sd0_pins_uhs: sd0-pins-uhs {
+ mux {
+ function = "sd";
+ groups = "sd_0";
+ };
+
+ conf-cmd-data {
+ pins = "I2S2_OUT", "I2S4_IN", "I2S3_IN",
+ "I2S2_IN","I2S4_OUT";
+ input-enable;
+ bias-pull-up;
+ };
+
+ conf-clk {
+ pins = "I2S3_OUT";
+ bias-pull-down;
+ };
+ };
+
+ /* Serial NAND is shared pin with SPI-NOR */
+ serial_nand_pins: serial-nand-pins {
+ mux {
+ function = "flash";
+ groups = "snfi";
+ };
+ };
+
+ spic0_pins: spic0-pins {
+ mux {
+ function = "spi";
+ groups = "spic0_0";
+ };
+ };
+
+ spic1_pins: spic1-pins {
+ mux {
+ function = "spi";
+ groups = "spic1_0";
+ };
+ };
+
+ /* SPI-NOR is shared pin with serial NAND */
+ spi_nor_pins: spi-nor-pins {
+ mux {
+ function = "flash";
+ groups = "spi_nor";
+ };
+ };
+
+ /* serial NAND is shared pin with SPI-NOR */
+ serial_nand_pins: serial-nand-pins {
+ mux {
+ function = "flash";
+ groups = "snfi";
+ };
+ };
+
+ uart0_pins: uart0-pins {
+ mux {
+ function = "uart";
+ groups = "uart0_0_tx_rx" ;
+ };
+ };
+
+ uart2_pins: uart2-pins {
+ mux {
+ function = "uart";
+ groups = "uart2_1_tx_rx" ;
+ };
+ };
+
+ watchdog_pins: watchdog-pins {
+ mux {
+ function = "watchdog";
+ groups = "watchdog";
+ };
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm7_pins>;
+ status = "okay";
+};
+
+&pwrap {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_bus_pins>;
+
+ status = "okay";
+};
+
+&sata {
+ status = "disable";
+};
+
+&sata_phy {
+ status = "disable";
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spic0_pins>;
+ status = "okay";
+};
+
+&spi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spic1_pins>;
+ status = "okay";
+};
+
+&ssusb {
+ vusb33-supply = <&reg_3p3v>;
+ vbus-supply = <&reg_5v>;
+ status = "okay";
+};
+
+&u3phy {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "okay";
+};
+
+&watchdog {
+ pinctrl-names = "default";
+ pinctrl-0 = <&watchdog_pins>;
+ status = "okay";
+};
--
1.9.1