[PATCH v2 1/2] dt-bindings: PCI: meson: add DT bindings for Amlogic Meson PCIe controller

[Hanjie Lin]

From: Yue Wang <yue.wang@xxxxxxxxxxx>

The Amlogic Meson PCIe host controller is based on the Synopsys DesignWare
PCI core. This patch adds documentation for the DT bindings in Meson PCIe
controller.

Signed-off-by: Yue Wang <yue.wang@xxxxxxxxxxx>
Signed-off-by: Hanjie Lin <hanjie.lin@xxxxxxxxxxx>
---
 .../devicetree/bindings/pci/amlogic,meson-pcie.txt | 63 ++++++++++++++++++++++
 1 file changed, 63 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt

diff --git a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
new file mode 100644
index 0000000..8a831d1
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
@@ -0,0 +1,63 @@
+Amlogic Meson AXG DWC PCIE SoC controller
+
+Amlogic Meson PCIe host controller is based on the Synopsys DesignWare PCI core.
+It shares common functions with the PCIe DesignWare core driver and
+inherits common properties defined in
+Documentation/devicetree/bindings/pci/designware-pci.txt.
+
+Additional properties are described here:
+
+Required properties:
+- compatible:
+	should contain "amlogic,axg-pcie" to identify the core.
+- reg:
+	Should contain the configuration address space.
+- reg-names: Must be
+	- "elbi"	External local bus interface registers
+	- "cfg"		Meson specific registers
+	- "config"	PCIe configuration space
+- reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal.
+- clocks: Must contain an entry for each entry in clock-names.
+- clock-names: Must include the following entries:
+	- "pclk"       PCIe GEN 100M PLL clock
+	- "port"       PCIe_x(A or B) RC clock gate
+	- "general"    PCIe Phy clock
+	- "mipi"       PCIe_x(A or B) 100M ref clock gate
+- resets: phandle to the reset lines.
+- reset-names: must contain "phy" and "peripheral"
+       - "port" Port A or B reset
+       - "apb" APB reset
+
+Example configuration:
+
+	pcie: pcie@f9800000 {
+			compatible = "amlogic,axg-pcie", "snps,dw-pcie";
+			reg = <0x0 0xf9800000 0x0 0x400000
+					0x0 0xff646000 0x0 0x2000
+					0x0 0xf9f00000 0x0 0x100000>;
+			reg-names = "elbi", "cfg", "config";
+			reset-gpios = <&gpio GPIOX_19 GPIO_ACTIVE_HIGH>;
+			interrupts = <GIC_SPI 177 IRQ_TYPE_EDGE_RISING>;
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0 0 0 0 &gic GIC_SPI 179 IRQ_TYPE_EDGE_RISING>;
+			bus-range = <0x0 0xff>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			phys = <&pcie_phy>;
+			ranges = <0x82000000 0 0 0x0 0xf9c00000 0 0x00300000>;
+
+			clocks = <&clkc CLKID_USB
+					&clkc CLKID_MIPI_ENABLE
+					&clkc CLKID_PCIE_A
+					&clkc CLKID_PCIE_CML_EN0>;
+			clock-names = "general",
+					"mipi",
+					"pclk",
+					"port";
+			resets = <&reset RESET_PCIE_A>,
+				<&reset RESET_PCIE_APB>;
+			reset-names = "port",
+					"apb";
+	};
-- 
2.7.4