Re: [PATCH v5 1/2] dt-bindings: hwmon: Add ina3221 documentation

[Guenter Roeck]

Hi Nicolin,

On 09/25/2018 03:59 PM, Nicolin Chen wrote:
> Texas Instruments INA3221 is a triple-channel shunt and bus
> voltage monitor. This patch adds a DT binding doc for it.
>
> Signed-off-by: Nicolin Chen <nicoleotsuka@xxxxxxxxx>
> ---
> Changelog
> v4->v5:
>   * Replaced "input-id" with "reg" and added address-cells and size-cells
>   * Replaced "input-label" with "label"
>   * Replaced "shunt-resistor" with "shunt-resistor-micro-ohms"
> v3->v4:
>   * Removed the attempt of putting labels in the node names
>   * Added a new optional label property in the child node
>   * Updated examples accordingly
> v2->v3:
>   * Added a simple subject in the line 1
>   * Fixed the shunt resistor value in the example
> v1->v2:
>   * Dropped channel name properties
>   * Added child node definitions.
>   * * Added shunt resistor property in the child node
>   * * Added status property to indicate connection status
>   * * Changed to use child node name as the label of input source
>
>   .../devicetree/bindings/hwmon/ina3221.txt     | 49 +++++++++++++++++++
>   1 file changed, 49 insertions(+)
>   create mode 100644 Documentation/devicetree/bindings/hwmon/ina3221.txt
>
> diff --git a/Documentation/devicetree/bindings/hwmon/ina3221.txt b/Documentation/devicetree/bindings/hwmon/ina3221.txt
> new file mode 100644
> index 000000000000..e17a897f4803
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/hwmon/ina3221.txt
> @@ -0,0 +1,49 @@
> +Texas Instruments INA3221 Device Tree Bindings
> +
> +1) ina3221 node
> +  Required properties:
> +  - compatible: Must be "ti,ina3221"
> +  - reg: I2C address
> +
> +  Optional properties:
> +  = The node contains optional child nodes for three channels =
> +  = Each child node describes the information of input source =
> +
> +  - #address-cells: Required only if a child node is present. Must be 1.
> +  - #size-cells: Required only if a child node is present. Must be 0.
> +
> +  Example:
> +
> +  ina3221@40 {
> +          compatible = "ti,ina3221";
> +          reg = <0x40>;
> +          #address-cells = <1>;
> +          #size-cells = <0>;
> +
> +          [ child node definitions... ]
> +  };
> +
> +2) child nodes
> +  Required properties:
> +  - reg: Must be 0, 1 or 2, corresponding to IN1, IN2 or IN3 port of INA3221
> +
> +  Optional properties:
> +  - label: Name of the input source
> +  - shunt-resistor-micro-ohms: Shunt resistor value in micro-Ohm
> +  - status: Should be "disabled" if no input source
> +
> +  Example:
> +
> +  input@0 {
> +          reg = <0x0>;
> +          status = "disabled";

I kind of feel embarrassed that I asked for the reg change ... especially while
saying at the same time that I would like to see this work for other chips
as well.

Other chips have different kinds of sensors. Voltage, current, power, temperature,
and others. Whatever we come up with should support that.

I see two possibilities right now. We can stick with reg and add a "type" property,
or we can make the index something like
	{voltage,current,power,temperature,humidity}-{id,index}

I personally prefer "type", but I don't really have a strong opinion.
What do you think ? Or maybe we should really wait for feedback from Rob.

Thanks,
Guenter

> +  };
> +  input@1 {
> +          reg = <0x1>;
> +          shunt-resistor-micro-ohms = <5000>;
> +  };
> +  input@2 {
> +          reg = <0x2>;
> +          label = "VDD_5V";
> +          shunt-resistor-micro-ohms = <5000>;
> +  };