On 09/25/2018 09:27 PM, Eddie James wrote:
The Video Engine (VE) embedded in the Aspeed AST2400 and AST2500 SOCsYou can also try to build it manually:
can capture and compress video data from digital or analog sources. With
the Aspeed chip acting as a service processor, the Video Engine can
capture the host processor graphics output.
This series adds a V4L2 driver for the VE, providing the usual V4L2 streaming
interface by way of videobuf2. Each frame, the driver triggers the hardware to
capture the host graphics output and compress it to JPEG format.
I was unable to cross compile v4l2-compliance for ARM with our OpenBMC
toolchain. Although bootstrap, configure, and make were successful, no binaries
were generated... I was able to build v4l-utils 1.12.3 from the OpenEmbedded
project, with the output below:
g++ -o v4l2-compliance -DNO_LIBV4L2 v4l2-compliance.cpp v4l2-test-debug.cpp v4l2-test-input-output.cpp v4l2-test-controls.cpp v4l2-test-io-config.cpp v4l2-test-formats.cpp v4l2-test-buffers.cpp
v4l2-test-codecs.cpp v4l2-test-colors.cpp v4l2-test-media.cpp v4l2-test-subdevs.cpp media-info.cpp v4l2-info.cpp -I../.. -I../../include -I../common
(replace g++ with your cross compiler)
Hopefully that will work since 1.12.3 is way too old.
Regards,
Hans
v4l2-compliance SHA : not available
Driver Info:
Driver name : aspeed-video
Card type : Aspeed Video Engine
Bus info : platform:aspeed-video
Driver version: 4.18.8
Capabilities : 0x85200001
Video Capture
Read/Write
Streaming
Extended Pix Format
Device Capabilities
Device Caps : 0x05200001
Video Capture
Read/Write
Streaming
Extended Pix Format
Compliance test for device /dev/video0 (not using libv4l2):
Required ioctls:
test VIDIOC_QUERYCAP: OK
Allow for multiple opens:
test second video open: OK
test VIDIOC_QUERYCAP: OK
test VIDIOC_G/S_PRIORITY: OK
test for unlimited opens: OK
Debug ioctls:
test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported)
test VIDIOC_LOG_STATUS: OK (Not Supported)
Input ioctls:
test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported)
test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported)
test VIDIOC_ENUMAUDIO: OK (Not Supported)
test VIDIOC_G/S/ENUMINPUT: OK
test VIDIOC_G/S_AUDIO: OK (Not Supported)
Inputs: 1 Audio Inputs: 0 Tuners: 0
Output ioctls:
test VIDIOC_G/S_MODULATOR: OK (Not Supported)
test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
test VIDIOC_ENUMAUDOUT: OK (Not Supported)
test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported)
test VIDIOC_G/S_AUDOUT: OK (Not Supported)
Outputs: 0 Audio Outputs: 0 Modulators: 0
Input/Output configuration ioctls:
test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported)
test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK
test VIDIOC_DV_TIMINGS_CAP: OK
test VIDIOC_G/S_EDID: OK
Test input 0:
Control ioctls:
test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK
test VIDIOC_QUERYCTRL: OK
test VIDIOC_G/S_CTRL: OK
test VIDIOC_G/S/TRY_EXT_CTRLS: OK
warn: ../../../v4l-utils-1.12.3/utils/v4l2-compliance/v4l2-test-controls.cpp(811): V4L2_CID_DV_RX_POWER_PRESENT not found for input 0
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK
test VIDIOC_G/S_JPEGCOMP: OK (Not Supported)
Standard Controls: 3 Private Controls: 0
Format ioctls:
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK
test VIDIOC_G/S_PARM: OK
test VIDIOC_G_FBUF: OK (Not Supported)
test VIDIOC_G_FMT: OK
test VIDIOC_TRY_FMT: OK
test VIDIOC_S_FMT: OK
test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported)
test Cropping: OK (Not Supported)
test Composing: OK (Not Supported)
test Scaling: OK (Not Supported)
Codec ioctls:
test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported)
test VIDIOC_G_ENC_INDEX: OK (Not Supported)
test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported)
Buffer ioctls:
test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
test VIDIOC_EXPBUF: OK (Not Supported)
Test input 0:
Streaming ioctls:
test read/write: OK
test MMAP: OK
test USERPTR: OK (Not Supported)
test DMABUF: OK (Not Supported)
Total: 47, Succeeded: 47, Failed: 0, Warnings: 1
Changes since v2:
- Switch to streaming interface. This involved a lot of changes.
- Rework memory allocation due to using videobuf2 buffers, but also only
allocate the necessary size of source buffer rather than the max size
Changes since v1:
- Removed le32_to_cpu calls for JPEG header data
- Reworked v4l2 ioctls to be compliant.
- Added JPEG controls
- Updated devicetree docs according to Rob's suggestions.
- Added myself to MAINTAINERS
Eddie James (2):
dt-bindings: media: Add Aspeed Video Engine binding documentation
media: platform: Add Aspeed Video Engine driver
.../devicetree/bindings/media/aspeed-video.txt | 26 +
MAINTAINERS | 8 +
drivers/media/platform/Kconfig | 8 +
drivers/media/platform/Makefile | 1 +
drivers/media/platform/aspeed-video.c | 1645 ++++++++++++++++++++
5 files changed, 1688 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/aspeed-video.txt
create mode 100644 drivers/media/platform/aspeed-video.c