Re: [PATCH v8 1/3] [media] imx214: device tree binding

[Rob Herring]

On Fri, Oct 05, 2018 at 02:49:37PM +0200, Ricardo Ribalda Delgado wrote:
> From: Ricardo Ribalda <ricardo.ribalda@xxxxxxxxx>
> 
> Document bindings for imx214 camera sensor
> 
> Cc: devicetree@xxxxxxxxxxxxxxx
> Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@xxxxxxxxx>

checkpatch.pl complains that the author and S-o-b don't match.

> ---
>  .../devicetree/bindings/media/i2c/imx214.txt  | 53 +++++++++++++++++++

sony,imx214.txt is preferred.

>  1 file changed, 53 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/imx214.txt
> 
> diff --git a/Documentation/devicetree/bindings/media/i2c/imx214.txt b/Documentation/devicetree/bindings/media/i2c/imx214.txt
> new file mode 100644
> index 000000000000..421a019ab7f9
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/imx214.txt
> @@ -0,0 +1,53 @@
> +* Sony 1/3.06-Inch 13.13Mp CMOS Digital Image Sensor
> +
> +The Sony imx214 is a 1/3.06-inch CMOS active pixel digital image sensor with
> +an active array size of 4224H x 3200V. It is programmable through an I2C
> +interface. The I2C address can be configured to 0x1a or 0x10, depending on
> +how the hardware is wired.

Move the addresses to reg description.

> +Image data is sent through MIPI CSI-2, through 2 or 4 lanes at a maximum
> +throughput of 1.2Gbps/lane.
> +
> +
> +Required Properties:
> +- compatible: value should be "sony,imx214" for imx214 sensor
> +- reg: I2C bus address of the device
> +- enable-gpios: GPIO descriptor for the enable pin.
> +- vdddo-supply: Chip digital IO regulator (1.8V).
> +- vdda-supply: Chip analog regulator (2.7V).
> +- vddd-supply: Chip digital core regulator (1.12V).
> +- clocks: Reference to the xclk clock.
> +- clock-names:  Shall be "xclk".
> +
> +Optional Properties:
> +- flash-leds: See ../video-interfaces.txt
> +- lens-focus: See ../video-interfaces.txt
> +
> +The imx214 device node shall contain one 'port' child node with
> +an 'endpoint' subnode. For further reading on port node refer to
> +Documentation/devicetree/bindings/media/video-interfaces.txt.
> +
> +Required Properties on endpoint:
> +- data-lanes: check ../video-interfaces.txt
> +- link-frequencies: check ../video-interfaces.txt
> +- remote-endpoint: check ../video-interfaces.txt
> +
> +Example:
> +
> +	camera_rear@1a {

camera-sensor@1a

If you need location, then perhaps use 'label'.

> +		compatible = "sony,imx214";
> +		reg = <0x1a>;
> +		vdddo-supply = <&pm8994_lvs1>;
> +		vddd-supply = <&camera_vddd_1v12>;
> +		vdda-supply = <&pm8994_l17>;
> +		lens-focus = <&ad5820>;
> +		enable-gpios = <&msmgpio 25 GPIO_ACTIVE_HIGH>;
> +		clocks = <&mmcc CAMSS_MCLK0_CLK>;
> +		clock-names = "xclk";
> +		port {
> +			imx214_ep: endpoint {
> +				data-lanes = <1 2 3 4>;
> +				link-frequencies = /bits/ 64 <480000000>;
> +				remote-endpoint = <&csiphy0_ep>;
> +			};
> +		};
> +	};
> -- 
> 2.19.0
>