[PATCH v3 lora-next 2/5] net: lora: sx1301: replace burst spi functions with regmap_noinc

[Ben Whitten]

We can now use to regmap_noinc API to allow reading and writing to
the internal FIFO register which controls processor memory.
We also remove the now defunct spi element from the structure as this
completes the move to regmap.

Signed-off-by: Ben Whitten <ben.whitten@xxxxxxxxxxxxx>
---
 drivers/net/lora/sx1301.c | 22 ++--------------------
 drivers/net/lora/sx1301.h |  2 --
 2 files changed, 2 insertions(+), 22 deletions(-)

diff --git a/drivers/net/lora/sx1301.c b/drivers/net/lora/sx1301.c
index fd29258..9c85fe7 100644
--- a/drivers/net/lora/sx1301.c
+++ b/drivers/net/lora/sx1301.c
@@ -74,23 +74,6 @@ static struct regmap_config sx1301_regmap_config = {
 	.max_register = SX1301_MAX_REGISTER,
 };
 
-static int sx1301_read_burst(struct sx1301_priv *priv, u8 reg, u8 *val, size_t len)
-{
-	u8 addr = reg & 0x7f;
-	return spi_write_then_read(priv->spi, &addr, 1, val, len);
-}
-
-static int sx1301_write_burst(struct sx1301_priv *priv, u8 reg, const u8 *val, size_t len)
-{
-	u8 addr = reg | BIT(7);
-	struct spi_transfer xfr[2] = {
-		{ .tx_buf = &addr, .len = 1 },
-		{ .tx_buf = val, .len = len },
-	};
-
-	return spi_sync_transfer(priv->spi, xfr, 2);
-}
-
 static int sx1301_soft_reset(struct sx1301_priv *priv)
 {
 	return regmap_write(priv->regmap, SX1301_PAGE, REG_PAGE_RESET_SOFT_RESET);
@@ -180,7 +163,7 @@ static int sx1301_load_firmware(struct sx1301_priv *priv, int mcu, const struct
 		return ret;
 	}
 
-	ret = sx1301_write_burst(priv, SX1301_MPD, fw->data, fw->size);
+	ret = regmap_noinc_write(priv->regmap, SX1301_MPD, fw->data, fw->size);
 	if (ret) {
 		dev_err(priv->dev, "MCU prom data write failed\n");
 		return ret;
@@ -196,7 +179,7 @@ static int sx1301_load_firmware(struct sx1301_priv *priv, int mcu, const struct
 	if (!buf)
 		return -ENOMEM;
 
-	ret = sx1301_read_burst(priv, SX1301_MPD, buf, fw->size);
+	ret = regmap_noinc_read(priv->regmap, SX1301_MPD, buf, fw->size);
 	if (ret) {
 		dev_err(priv->dev, "MCU prom data read failed\n");
 		kfree(buf);
@@ -566,7 +549,6 @@ static int sx1301_probe(struct spi_device *spi)
 
 	spi_set_drvdata(spi, netdev);
 	priv->dev = &spi->dev;
-	priv->spi = spi;
 
 	priv->regmap = devm_regmap_init_spi(spi, &sx1301_regmap_config);
 	if (IS_ERR(priv->regmap)) {
diff --git a/drivers/net/lora/sx1301.h b/drivers/net/lora/sx1301.h
index e939c02..e6400f8 100644
--- a/drivers/net/lora/sx1301.h
+++ b/drivers/net/lora/sx1301.h
@@ -12,7 +12,6 @@
 #include <linux/regmap.h>
 #include <linux/gpio/consumer.h>
 #include <linux/lora/dev.h>
-#include <linux/spi/spi.h>
 
 #define SX1301_CHIP_VERSION 103
 
@@ -64,7 +63,6 @@
 struct sx1301_priv {
 	struct lora_dev_priv lora;
 	struct device		*dev;
-	struct spi_device	*spi;
 	struct gpio_desc *rst_gpio;
 	struct regmap		*regmap;
 };
-- 
2.7.4