Re: [PATCH 3/7] dt-bindings: pinctrl: ds90ux9xx: add description of TI DS90Ux9xx pinmux

[Vladimir Zapolskiy]

Hi Laurent,

thank you for review, please find my comments below.

On 10/12/2018 03:01 PM, Laurent Pinchart wrote:
> Hi Vladimir,
> 
> Thank you for the patch.
> 
> On Tuesday, 9 October 2018 00:12:01 EEST Vladimir Zapolskiy wrote:
>> From: Vladimir Zapolskiy <vladimir_zapolskiy@xxxxxxxxxx>
>>
>> TI DS90Ux9xx de-/serializers have a capability to multiplex pin functions,
>> in particular a pin may have selectable functions of GPIO, GPIO line
>> transmitter, one of I2S lines, one of RGB24 video signal lines and so on.
>>
>> The change adds a description of DS90Ux9xx pin multiplexers and GPIO
>> controllers.
>>
>> Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@xxxxxxxxxx>
>> ---
>>  .../bindings/pinctrl/ti,ds90ux9xx-pinctrl.txt | 83 +++++++++++++++++++
>>  1 file changed, 83 insertions(+)
>>  create mode 100644
>> Documentation/devicetree/bindings/pinctrl/ti,ds90ux9xx-pinctrl.txt
>>
>> diff --git
>> a/Documentation/devicetree/bindings/pinctrl/ti,ds90ux9xx-pinctrl.txt
>> b/Documentation/devicetree/bindings/pinctrl/ti,ds90ux9xx-pinctrl.txt new
>> file mode 100644
>> index 000000000000..fbfa1a3cdf9f
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/pinctrl/ti,ds90ux9xx-pinctrl.txt
>> @@ -0,0 +1,83 @@
>> +TI DS90Ux9xx de-/serializer pinmux and GPIO subcontroller
>> +
>> +Required properties:
>> +- compatible: Must contain a generic "ti,ds90ux9xx-pinctrl" value and
>> +	may contain one more specific value from the list:
>> +	"ti,ds90ux925-pinctrl",
>> +	"ti,ds90ux926-pinctrl",
>> +	"ti,ds90ux927-pinctrl",
>> +	"ti,ds90ux928-pinctrl",
>> +	"ti,ds90ux940-pinctrl".
> 
> No need for a subnode, you can mark the main DT node with gpio-controller 
> directly.

If the IC is seen as an MFD, and you guess I highly prefer it and I object
the "overkill" argument, then the subnode is requred.

Also the more complicated part of the subcontroller and its device driver
is to provide pinmuxing function to consumers rather than to allow GPIO
line configuration.

The pinctrl/GPIO driver can not be alloyed with the base driver's code
to sustain maintainability, so it will reside in drivers/pinctrl as
a separate cell driver, and by the way that is the reason why it earns
its own very non-trivial DT binding description documentation.

>> +- gpio-controller: Marks the device node as a GPIO controller.
>> +
>> +- #gpio-cells: Must be set to 2,
>> +	- the first cell is the GPIO offset number within the controller,
>> +	- the second cell is used to specify the GPIO line polarity.
>> +
>> +- gpio-ranges: Mapping to pin controller pins (as described in
>> +	Documentation/devicetree/bindings/gpio/gpio.txt)
>> +
>> +Optional properties:
>> +- ti,video-depth-18bit: Sets video bridge pins to RGB 18-bit mode.
> 
> Please use standard properties to configure bus width. There is one defined in 
> Documentation/devicetree/bindings/media/video-interfaces.txt.

Here it is not a bus width description or property, but rather it is a custom
pinmux control.

It could make sense to reduce the scope of the property to "parallel" pin
function only though, like in

	ds90ux927_0_pins: pinmux {
		parallel {
			groups = "parallel";
			function = "parallel";
			ti,video-depth-18bit;
		};
	};

Alternatively the removal of the property would be almost loseless, it is
needed just in one very specific case, please reference to the driver code
for details, there you'll find a comment in ds90ux9xx_parse_dt_properties()
function.

>> +Available pins, groups and functions (reference to device datasheets):
>> +
>> +function: "gpio" ("gpio4" is on DS90Ux925 and DS90Ux926 only,
>> +		  "gpio9" is on DS90Ux940 only)
>> + - pins: "gpio0", "gpio1", "gpio2", "gpio3", "gpio4", "gpio5", "gpio6",
>> +	 "gpio7", "gpio8", "gpio9"
>> +
>> +function: "gpio-remote"
>> + - pins: "gpio0", "gpio1", "gpio2", "gpio3"
>> +
>> +function: "pass" (DS90Ux940 specific only)
>> + - pins: "gpio0", "gpio3"
> 
> What do those functions mean ?
> 

"gpio" function should be already familiar to you.

"gpio-remote" function is the pin function for a GPIO line bridging.

"pass" function sets a pin to a status pin function for detecting
display timing issues, namely DE or Vsync length value mismatch.

>> +function: "i2s-1"
>> + - group: "i2s-1"
>> +
>> +function: "i2s-2"
>> + - group: "i2s-2"
>> +
>> +function: "i2s-3" (DS90Ux927, DS90Ux928 and DS90Ux940 specific only)
>> + - group: "i2s-3"
>> +
>> +function: "i2s-4" (DS90Ux927, DS90Ux928 and DS90Ux940 specific only)
>> + - group: "i2s-4"
>> +
>> +function: "i2s-m" (DS90Ux928 and DS90Ux940 specific only)
>> + - group: "i2s-m"
> 
> Do we really need all this ? I think a better model would be to describe the 
> audio interfaces explicitly, and configure pinmuxing automatically based on 
> which audio interfaces are in use.

Yes, all the pin functions are needed, because they are transparent pinmux
controls.

I really don't want to copy a part of gpio and pinctrl frameworks to
the driver to hunt out why a user configured audio bridging and a GPIO
line, and then something goes funny due to a pin conflict. To forget
about such very possible pin and pin function conflicts I'm happy to
shift the task to the neat Linus' frameworks.

>> +function: "parallel" (DS90Ux925 and DS90Ux926 specific only)
>> + - group: "parallel"
>> +
>> +Example (deserializer with pins GPIO[3:0] set to bridged output
>> +	 function and pin GPIO4 in standard hogged GPIO function):
>> +
>> +deserializer {
>> +	compatible = "ti,ds90ub928q", "ti,ds90ux9xx";
>> +
>> +	ds90ux928_pctrl: pin-controller {
>> +		compatible = "ti,ds90ux928-pinctrl", "ti,ds90ux9xx-pinctrl";
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +		gpio-ranges = <&ds90ux928_pctrl 0 0 8>;
>> +
>> +		pinctrl-names = "default";
>> +		pinctrl-0 = <&ds90ux928_pins>;
>> +
>> +		ds90ux928_pins: pinmux {
>> +			gpio-remote {
>> +				pins = "gpio0", "gpio1", "gpio2", "gpio3";
>> +				function = "gpio-remote";
>> +			};
>> +		};
>> +
>> +		rst {
>> +			gpio-hog;
>> +			gpios = <4 GPIO_ACTIVE_HIGH>;
>> +			output-high;
>> +		};
>> +	};
>> +};
> 

--
Best wishes,
Vladimir