Re: [PATCH] power: reset: at91-reset: enable I-cache for at91sam9260_reset

[Alexander Stein]

Do you have CONFIG_CPU_ICACHE_DISABLE enabled?
I wonder why I-cache is disabled. I know about this errata, AT91SAM9G20 is affected as well.

Best regards,
Alexander

On Sunday, October 7, 2018, 2:57:45 PM CEST Jonas Danielsson wrote:
> From: Jonas Danielsson <jonas@xxxxxxxxxxxxxxxxxxx>
> 
> This fixes a bug where our embedded system (AT91SAM9260 based) would
> hang at reboot. At the most we managed 16 boot loops without a hang.
> 
> With this patch applied the problem has not been observed and the board
> has managed above 250 boot loops.
> 
> The AT91SAM9260 datasheet tells us that with the instruction cache
> disabled all instructions are fetched from SDRAM. And we have an errata
> telling us we must power down the SDRAM before issuing cpu reset.
> 
> This means we need the instruction cache enabled in at91sam9260_reset()
> At the moment it is being disabled in cpu_proc_fin() which is called from
> arch/arm/kernel/reboot.c.
> 
> Signed-off-by: Jonas Danielsson <jonas@xxxxxxxxxxxxxxxxxxx>
> ---
>  drivers/power/reset/at91-reset.c | 12 +++++++++++-
>  1 file changed, 11 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/power/reset/at91-reset.c b/drivers/power/reset/at91-reset.c
> index f44a9ffcc2ab..78972bba64df 100644
> --- a/drivers/power/reset/at91-reset.c
> +++ b/drivers/power/reset/at91-reset.c
> @@ -50,14 +50,24 @@ static void __iomem *at91_ramc_base[2], *at91_rstc_base;
>  static struct clk *sclk;
>  
>  /*
> -* unless the SDRAM is cleanly shutdown before we hit the
> +* Errata 43.1.7.1 RSTC: Reset during SDRAM Accesses
> +*
> +* Unless the SDRAM is cleanly shutdown before we hit the
>  * reset register it can be left driving the data bus and
>  * killing the chance of a subsequent boot from NAND
> +*
> +* Since we are disabling SDRAM need to make sure that the
> +* instruction cache is enabled.
>  */
>  static int at91sam9260_restart(struct notifier_block *this, unsigned long mode,
>  			       void *cmd)
>  {
>  	asm volatile(
> +		/* Enable I-cache */
> +		"mrc	p15, 0, r0, c1, c0, 0\n\t"
> +		"orr	r0, r0, #4096\n\t" /* CR_I (bit 12) */
> +		"mcr	p15, 0, r0, c1, c0, 0\n\t"
> +
>  		/* Align to cache lines */
>  		".balign 32\n\t"
>  
> 


-- 
SYS TEC electronic GmbH
Am Windrad 2
08468 Heinsdorfergrund
Germany
Telefon : +49 (0) 3765 38600-0
Fax     : +49 (0) 3765 38600-4100
Email   : alexander.stein@xxxxxxxxxxxxxxxxxxxxx
Website : http://www.systec-electronic.com

Managing Director   : Dipl.-Phys. Siegmar Schmidt
Commercial registry : Amtsgericht Chemnitz, HRB 28082
USt.-Id Nr.         : DE150534010

Diese E-Mail enthält vertrauliche und/oder rechtlich geschützte Informationen.
Wenn Sie nicht der richtige Adressat sind oder diese E-Mail irrtümlich erhalten haben, informieren Sie bitte sofort den Absender und vernichten Sie diese Mail.
Das unerlaubte Kopieren sowie die unbefugte Weitergabe dieser Mail sind nicht gestattet.
 
This e-mail may contain confidential and/or privileged information.
If you are not the intended recipient (or have received this e-mail in error) please notify the sender immediately and destroy this e-mail.
Any unauthorized copying, disclosure or distribution of the material in this e-mail is strictly forbidden.