[PATCH v2 08/22] dt-bindings: clk: at91: Document new PMC binding
From: Alexandre Belloni
Date: Tue Oct 16 2018 - 10:22:32 EST
Document the new PMC binding with only one PMC node for all the PMC clocks
instead of one node per clock as this proved to be problematic.
Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
Signed-off-by: Alexandre Belloni <alexandre.belloni@xxxxxxxxxxx>
---
.../devicetree/bindings/clock/at91-clock.txt | 516 +-----------------
1 file changed, 21 insertions(+), 495 deletions(-)
diff --git a/Documentation/devicetree/bindings/clock/at91-clock.txt b/Documentation/devicetree/bindings/clock/at91-clock.txt
index 8f8f95056f3d..e9f70fcdfe80 100644
--- a/Documentation/devicetree/bindings/clock/at91-clock.txt
+++ b/Documentation/devicetree/bindings/clock/at91-clock.txt
@@ -4,6 +4,8 @@ This binding uses the common clock binding[1].
[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+Slow Clock controller:
+
Required properties:
- compatible : shall be one of the following:
"atmel,at91sam9x5-sckc" or
@@ -16,84 +18,6 @@ Required properties:
"atmel,at91sam9x5-clk-slow-rc-osc":
at91 internal slow RC oscillator
-
- "atmel,<chip>-pmc":
- at91 PMC (Power Management Controller)
- All at91 specific clocks (clocks defined below) must be child
- node of the PMC node.
- <chip> can be: at91rm9200, at91sam9260, at91sam9261,
- at91sam9263, at91sam9g45, at91sam9n12, at91sam9rl, at91sam9x5,
- sama5d2, sama5d3 or sama5d4.
-
- "atmel,at91sam9x5-clk-slow" (under sckc node)
- or
- "atmel,at91sam9260-clk-slow" (under pmc node):
- at91 slow clk
-
- "atmel,at91rm9200-clk-main-osc"
- "atmel,at91sam9x5-clk-main-rc-osc"
- at91 main clk sources
-
- "atmel,at91sam9x5-clk-main"
- "atmel,at91rm9200-clk-main":
- at91 main clock
-
- "atmel,at91rm9200-clk-master" or
- "atmel,at91sam9x5-clk-master":
- at91 master clock
-
- "atmel,at91sam9x5-clk-peripheral" or
- "atmel,at91rm9200-clk-peripheral":
- at91 peripheral clocks
-
- "atmel,at91rm9200-clk-pll" or
- "atmel,at91sam9g45-clk-pll" or
- "atmel,at91sam9g20-clk-pllb" or
- "atmel,sama5d3-clk-pll":
- at91 pll clocks
-
- "atmel,at91sam9x5-clk-plldiv":
- at91 plla divisor
-
- "atmel,at91rm9200-clk-programmable" or
- "atmel,at91sam9g45-clk-programmable" or
- "atmel,at91sam9x5-clk-programmable":
- at91 programmable clocks
-
- "atmel,at91sam9x5-clk-smd":
- at91 SMD (Soft Modem) clock
-
- "atmel,at91rm9200-clk-system":
- at91 system clocks
-
- "atmel,at91rm9200-clk-usb" or
- "atmel,at91sam9x5-clk-usb" or
- "atmel,at91sam9n12-clk-usb":
- at91 usb clock
-
- "atmel,at91sam9x5-clk-utmi":
- at91 utmi clock
-
- "atmel,sama5d4-clk-h32mx":
- at91 h32mx clock
-
- "atmel,sama5d2-clk-generated":
- at91 generated clock
-
- "atmel,sama5d2-clk-audio-pll-frac":
- at91 audio fractional pll
-
- "atmel,sama5d2-clk-audio-pll-pad":
- at91 audio pll CLK_AUDIO output pin
-
- "atmel,sama5d2-clk-audio-pll-pmc"
- at91 audio pll output on AUDIOPLLCLK that feeds the PMC
- and can be used by peripheral clock or generic clock
-
- "atmel,sama5d2-clk-i2s-mux" (under pmc node):
- at91 I2S clock source selection
-
-Required properties for SCKC node:
- reg : defines the IO memory reserved for the SCKC.
- #size-cells : shall be 0 (reg is used to encode clk id).
- #address-cells : shall be 1 (reg is used to encode clk id).
@@ -109,428 +33,30 @@ For example:
/* put at91 slow clocks here */
};
+Power Management Controller (PMC):
-Required properties for internal slow RC oscillator:
-- #clock-cells : from common clock binding; shall be set to 0.
-- clock-frequency : define the internal RC oscillator frequency.
-
-Optional properties:
-- clock-accuracy : define the internal RC oscillator accuracy.
-
-For example:
- slow_rc_osc: slow_rc_osc {
- compatible = "atmel,at91sam9x5-clk-slow-rc-osc";
- clock-frequency = <32768>;
- clock-accuracy = <50000000>;
- };
-
-Required properties for slow oscillator:
-- #clock-cells : from common clock binding; shall be set to 0.
-- clocks : shall encode the main osc source clk sources (see atmel datasheet).
+Required properties:
+- compatible : shall be "atmel,<chip>-pmc", "syscon":
+ <chip> can be: at91rm9200, at91sam9260, at91sam9261,
+ at91sam9263, at91sam9g45, at91sam9n12, at91sam9rl, at91sam9g15,
+ at91sam9g25, at91sam9g35, at91sam9x25, at91sam9x35, at91sam9x5,
+ sama5d2, sama5d3 or sama5d4.
+- #clock-cells : from common clock binding; shall be set to 2. The first entry
+ is the type of the clock (core, system, peripheral or generated) and the
+ second entry its index as provided by the datasheet
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names: Must include the following entries: "slow_clk", "main_xtal"
Optional properties:
- atmel,osc-bypass : boolean property. Set this when a clock signal is directly
provided on XIN.
For example:
- slow_osc: slow_osc {
- compatible = "atmel,at91rm9200-clk-slow-osc";
- #clock-cells = <0>;
- clocks = <&slow_xtal>;
- };
-
-Required properties for slow clock:
-- #clock-cells : from common clock binding; shall be set to 0.
-- clocks : shall encode the slow clk sources (see atmel datasheet).
-
-For example:
- clk32k: slck {
- compatible = "atmel,at91sam9x5-clk-slow";
- #clock-cells = <0>;
- clocks = <&slow_rc_osc &slow_osc>;
- };
-
-Required properties for PMC node:
-- reg : defines the IO memory reserved for the PMC.
-- #size-cells : shall be 0 (reg is used to encode clk id).
-- #address-cells : shall be 1 (reg is used to encode clk id).
-- interrupts : shall be set to PMC interrupt line.
-- interrupt-controller : tell that the PMC is an interrupt controller.
-- #interrupt-cells : must be set to 1. The first cell encodes the interrupt id,
- and reflect the bit position in the PMC_ER/DR/SR registers.
- You can use the dt macros defined in dt-bindings/clock/at91.h.
- 0 (AT91_PMC_MOSCS) -> main oscillator ready
- 1 (AT91_PMC_LOCKA) -> PLL A ready
- 2 (AT91_PMC_LOCKB) -> PLL B ready
- 3 (AT91_PMC_MCKRDY) -> master clock ready
- 6 (AT91_PMC_LOCKU) -> UTMI PLL clock ready
- 8 .. 15 (AT91_PMC_PCKRDY(id)) -> programmable clock ready
- 16 (AT91_PMC_MOSCSELS) -> main oscillator selected
- 17 (AT91_PMC_MOSCRCS) -> RC main oscillator stabilized
- 18 (AT91_PMC_CFDEV) -> clock failure detected
-
-For example:
- pmc: pmc@fffffc00 {
- compatible = "atmel,sama5d3-pmc";
- interrupts = <1 4 7>;
- interrupt-controller;
- #interrupt-cells = <2>;
- #size-cells = <0>;
- #address-cells = <1>;
-
- /* put at91 clocks here */
- };
-
-Required properties for main clock internal RC oscillator:
-- interrupts : shall be set to "<0>".
-- clock-frequency : define the internal RC oscillator frequency.
-
-Optional properties:
-- clock-accuracy : define the internal RC oscillator accuracy.
-
-For example:
- main_rc_osc: main_rc_osc {
- compatible = "atmel,at91sam9x5-clk-main-rc-osc";
- interrupt-parent = <&pmc>;
- interrupts = <0>;
- clock-frequency = <12000000>;
- clock-accuracy = <50000000>;
- };
-
-Required properties for main clock oscillator:
-- interrupts : shall be set to "<0>".
-- #clock-cells : from common clock binding; shall be set to 0.
-- clocks : shall encode the main osc source clk sources (see atmel datasheet).
-
-Optional properties:
-- atmel,osc-bypass : boolean property. Specified if a clock signal is provided
- on XIN.
-
- clock signal is directly provided on XIN pin.
-
-For example:
- main_osc: main_osc {
- compatible = "atmel,at91rm9200-clk-main-osc";
- interrupt-parent = <&pmc>;
- interrupts = <0>;
- #clock-cells = <0>;
- clocks = <&main_xtal>;
- };
-
-Required properties for main clock:
-- interrupts : shall be set to "<0>".
-- #clock-cells : from common clock binding; shall be set to 0.
-- clocks : shall encode the main clk sources (see atmel datasheet).
-
-For example:
- main: mainck {
- compatible = "atmel,at91sam9x5-clk-main";
- interrupt-parent = <&pmc>;
- interrupts = <0>;
- #clock-cells = <0>;
- clocks = <&main_rc_osc &main_osc>;
- };
-
-Required properties for master clock:
-- interrupts : shall be set to "<3>".
-- #clock-cells : from common clock binding; shall be set to 0.
-- clocks : shall be the master clock sources (see atmel datasheet) phandles.
- e.g. "<&ck32k>, <&main>, <&plla>, <&pllb>".
-- atmel,clk-output-range : minimum and maximum clock frequency (two u32
- fields).
- e.g. output = <0 133000000>; <=> 0 to 133MHz.
-- atmel,clk-divisors : master clock divisors table (four u32 fields).
- 0 <=> reserved value.
- e.g. divisors = <1 2 4 6>;
-- atmel,master-clk-have-div3-pres : some SoC use the reserved value 7 in the
- PRES field as CLOCK_DIV3 (e.g sam9x5).
-
-For example:
- mck: mck {
- compatible = "atmel,at91rm9200-clk-master";
- interrupt-parent = <&pmc>;
- interrupts = <3>;
- #clock-cells = <0>;
- atmel,clk-output-range = <0 133000000>;
- atmel,clk-divisors = <1 2 4 0>;
- };
-
-Required properties for peripheral clocks:
-- #size-cells : shall be 0 (reg is used to encode clk id).
-- #address-cells : shall be 1 (reg is used to encode clk id).
-- clocks : shall be the master clock phandle.
- e.g. clocks = <&mck>;
-- name: device tree node describing a specific peripheral clock.
- * #clock-cells : from common clock binding; shall be set to 0.
- * reg: peripheral id. See Atmel's datasheets to get a full
- list of peripheral ids.
- * atmel,clk-output-range : minimum and maximum clock frequency
- (two u32 fields). Only valid on at91sam9x5-clk-peripheral
- compatible IPs.
-
-For example:
- periph: periphck {
- compatible = "atmel,at91sam9x5-clk-peripheral";
- #size-cells = <0>;
- #address-cells = <1>;
- clocks = <&mck>;
-
- ssc0_clk {
- #clock-cells = <0>;
- reg = <2>;
- atmel,clk-output-range = <0 133000000>;
- };
-
- usart0_clk {
- #clock-cells = <0>;
- reg = <3>;
- atmel,clk-output-range = <0 66000000>;
- };
- };
-
-
-Required properties for pll clocks:
-- interrupts : shall be set to "<1>".
-- #clock-cells : from common clock binding; shall be set to 0.
-- clocks : shall be the main clock phandle.
-- reg : pll id.
- 0 -> PLL A
- 1 -> PLL B
-- atmel,clk-input-range : minimum and maximum source clock frequency (two u32
- fields).
- e.g. input = <1 32000000>; <=> 1 to 32MHz.
-- #atmel,pll-clk-output-range-cells : number of cells reserved for pll output
- range description. Sould be set to 2, 3
- or 4.
- * 1st and 2nd cells represent the frequency range (min-max).
- * 3rd cell is optional and represents the OUT field value for the given
- range.
- * 4th cell is optional and represents the ICPLL field (PLLICPR
- register)
-- atmel,pll-clk-output-ranges : pll output frequency ranges + optional parameter
- depending on #atmel,pll-output-range-cells
- property value.
-
-For example:
- plla: pllack {
- compatible = "atmel,at91sam9g45-clk-pll";
- interrupt-parent = <&pmc>;
- interrupts = <1>;
- #clock-cells = <0>;
- clocks = <&main>;
- reg = <0>;
- atmel,clk-input-range = <2000000 32000000>;
- #atmel,pll-clk-output-range-cells = <4>;
- atmel,pll-clk-output-ranges = <74500000 800000000 0 0
- 69500000 750000000 1 0
- 64500000 700000000 2 0
- 59500000 650000000 3 0
- 54500000 600000000 0 1
- 49500000 550000000 1 1
- 44500000 500000000 2 1
- 40000000 450000000 3 1>;
- };
-
-Required properties for plldiv clocks (plldiv = pll / 2):
-- #clock-cells : from common clock binding; shall be set to 0.
-- clocks : shall be the plla clock phandle.
-
-The pll divisor is equal to 2 and cannot be changed.
-
-For example:
- plladiv: plladivck {
- compatible = "atmel,at91sam9x5-clk-plldiv";
- #clock-cells = <0>;
- clocks = <&plla>;
- };
-
-Required properties for programmable clocks:
-- #size-cells : shall be 0 (reg is used to encode clk id).
-- #address-cells : shall be 1 (reg is used to encode clk id).
-- clocks : shall be the programmable clock source phandles.
- e.g. clocks = <&clk32k>, <&main>, <&plla>, <&pllb>;
-- name: device tree node describing a specific prog clock.
- * #clock-cells : from common clock binding; shall be set to 0.
- * reg : programmable clock id (register offset from PCKx
- register).
- * interrupts : shall be set to "<(8 + id)>".
-
-For example:
- prog: progck {
- compatible = "atmel,at91sam9g45-clk-programmable";
- #size-cells = <0>;
- #address-cells = <1>;
- interrupt-parent = <&pmc>;
- clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>;
-
- prog0 {
- #clock-cells = <0>;
- reg = <0>;
- interrupts = <8>;
- };
-
- prog1 {
- #clock-cells = <0>;
- reg = <1>;
- interrupts = <9>;
- };
- };
-
-
-Required properties for smd clock:
-- #clock-cells : from common clock binding; shall be set to 0.
-- clocks : shall be the smd clock source phandles.
- e.g. clocks = <&plladiv>, <&utmi>;
-
-For example:
- smd: smdck {
- compatible = "atmel,at91sam9x5-clk-smd";
- #clock-cells = <0>;
- clocks = <&plladiv>, <&utmi>;
- };
-
-Required properties for system clocks:
-- #size-cells : shall be 0 (reg is used to encode clk id).
-- #address-cells : shall be 1 (reg is used to encode clk id).
-- name: device tree node describing a specific system clock.
- * #clock-cells : from common clock binding; shall be set to 0.
- * reg: system clock id (bit position in SCER/SCDR/SCSR registers).
- See Atmel's datasheet to get a full list of system clock ids.
-
-For example:
- system: systemck {
- compatible = "atmel,at91rm9200-clk-system";
- #address-cells = <1>;
- #size-cells = <0>;
-
- ddrck {
- #clock-cells = <0>;
- reg = <2>;
- clocks = <&mck>;
- };
-
- uhpck {
- #clock-cells = <0>;
- reg = <6>;
- clocks = <&usb>;
- };
-
- udpck {
- #clock-cells = <0>;
- reg = <7>;
- clocks = <&usb>;
- };
- };
-
-
-Required properties for usb clock:
-- #clock-cells : from common clock binding; shall be set to 0.
-- clocks : shall be the smd clock source phandles.
- e.g. clocks = <&pllb>;
-- atmel,clk-divisors (only available for "atmel,at91rm9200-clk-usb"):
- usb clock divisor table.
- e.g. divisors = <1 2 4 0>;
-
-For example:
- usb: usbck {
- compatible = "atmel,at91sam9x5-clk-usb";
- #clock-cells = <0>;
- clocks = <&plladiv>, <&utmi>;
- };
-
- usb: usbck {
- compatible = "atmel,at91rm9200-clk-usb";
- #clock-cells = <0>;
- clocks = <&pllb>;
- atmel,clk-divisors = <1 2 4 0>;
- };
-
-
-Required properties for utmi clock:
-- interrupts : shall be set to "<AT91_PMC_LOCKU IRQ_TYPE_LEVEL_HIGH>".
-- #clock-cells : from common clock binding; shall be set to 0.
-- clocks : shall be the main clock source phandle.
-
-For example:
- utmi: utmick {
- compatible = "atmel,at91sam9x5-clk-utmi";
- interrupt-parent = <&pmc>;
- interrupts = <AT91_PMC_LOCKU IRQ_TYPE_LEVEL_HIGH>;
- #clock-cells = <0>;
- clocks = <&main>;
- };
-
-Required properties for 32 bits bus Matrix clock (h32mx clock):
-- #clock-cells : from common clock binding; shall be set to 0.
-- clocks : shall be the master clock source phandle.
-
-For example:
- h32ck: h32mxck {
- #clock-cells = <0>;
- compatible = "atmel,sama5d4-clk-h32mx";
- clocks = <&mck>;
- };
-
-Required properties for generated clocks:
-- #size-cells : shall be 0 (reg is used to encode clk id).
-- #address-cells : shall be 1 (reg is used to encode clk id).
-- clocks : shall be the generated clock source phandles.
- e.g. clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>, <&audio_pll_pmc>;
-- name: device tree node describing a specific generated clock.
- * #clock-cells : from common clock binding; shall be set to 0.
- * reg: peripheral id. See Atmel's datasheets to get a full
- list of peripheral ids.
- * atmel,clk-output-range : minimum and maximum clock frequency
- (two u32 fields).
-
-For example:
- gck {
- compatible = "atmel,sama5d2-clk-generated";
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>, <&audio_pll_pmc>;
-
- tcb0_gclk: tcb0_gclk {
- #clock-cells = <0>;
- reg = <35>;
- atmel,clk-output-range = <0 83000000>;
- };
-
- pwm_gclk: pwm_gclk {
- #clock-cells = <0>;
- reg = <38>;
- atmel,clk-output-range = <0 83000000>;
- };
- };
-
-Required properties for I2S mux clocks:
-- #size-cells : shall be 0 (reg is used to encode I2S bus id).
-- #address-cells : shall be 1 (reg is used to encode I2S bus id).
-- name: device tree node describing a specific mux clock.
- * #clock-cells : from common clock binding; shall be set to 0.
- * clocks : shall be the mux clock parent phandles; shall be 2 phandles:
- peripheral and generated clock; the first phandle shall belong to the
- peripheral clock and the second one shall belong to the generated
- clock; "clock-indices" property can be user to specify
- the correct order.
- * reg: I2S bus id of the corresponding mux clock.
- e.g. reg = <0>; for i2s0, reg = <1>; for i2s1
-
-For example:
- i2s_clkmux {
- compatible = "atmel,sama5d2-clk-i2s-mux";
- #address-cells = <1>;
- #size-cells = <0>;
-
- i2s0muxck: i2s0_muxclk {
- clocks = <&i2s0_clk>, <&i2s0_gclk>;
- #clock-cells = <0>;
- reg = <0>;
- };
-
- i2s1muxck: i2s1_muxclk {
- clocks = <&i2s1_clk>, <&i2s1_gclk>;
- #clock-cells = <0>;
- reg = <1>;
- };
+ pmc: pmc@f0018000 {
+ compatible = "atmel,sama5d4-pmc", "syscon";
+ reg = <0xf0018000 0x120>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ #clock-cells = <2>;
+ clocks = <&clk32k>, <&main_xtal>;
+ clock-names = "slow_clk", "main_xtal";
};
--
2.19.1