Re: [RFC PATCH 04/11] dt-bindings: net: ti: cpsw: switch to use phy-gmii-sel phy

[Rob Herring]

On Mon, Oct 08, 2018 at 06:49:42PM -0500, Grygorii Strashko wrote:
> The cpsw-phy-sel driver was replaced with new PHY driver phy-gmii-sel, so
> deprecate cpsw-phy-sel bindings and update CPSW binding to use phy-gmii-sel
> PHY bindings.
> 
> Cc: Kishon Vijay Abraham I <kishon@xxxxxx>
> Cc: Tony Lindgren <tony@xxxxxxxxxxx>
> Signed-off-by: Grygorii Strashko <grygorii.strashko@xxxxxx>
> ---
>  Documentation/devicetree/bindings/net/cpsw.txt | 8 +++++++-
>  1 file changed, 7 insertions(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt
> index b3acebe..69d7ef8 100644
> --- a/Documentation/devicetree/bindings/net/cpsw.txt
> +++ b/Documentation/devicetree/bindings/net/cpsw.txt
> @@ -22,7 +22,8 @@ Required properties:
>  - cpsw-phy-sel		: Specifies the phandle to the CPSW phy mode selection
>  			  device. See also cpsw-phy-sel.txt for it's binding.
>  			  Note that in legacy cases cpsw-phy-sel may be
> -			  a child device instead of a phandle.
> +			  a child device instead of a phandle
> +			  (DEPRECATED, use phy-gmii-sel PHY phandle).

phy-gmii-sel is outside the scope of this binding. Just say use 'phys' 
property instead.

>  
>  Optional properties:
>  - ti,hwmods		: Must be "cpgmac0"
> @@ -44,6 +45,7 @@ Optional properties:
>  Slave Properties:
>  Required properties:
>  - phy-mode		: See ethernet.txt file in the same directory
> +- phys			: phandle on phy-gmii-sel PHY (see phy/ti-phy-gmii-sel.txt)
>  
>  Optional properties:
>  - dual_emac_res_vlan	: Specifies VID to be used to segregate the ports
> @@ -85,12 +87,14 @@ Examples:
>  			phy-mode = "rgmii-txid";
>  			/* Filled in by U-Boot */
>  			mac-address = [ 00 00 00 00 00 00 ];
> +			phys = <&phy_gmii_sel 1 0>;
>  		};
>  		cpsw_emac1: slave@1 {
>  			phy_id = <&davinci_mdio>, <1>;
>  			phy-mode = "rgmii-txid";
>  			/* Filled in by U-Boot */
>  			mac-address = [ 00 00 00 00 00 00 ];
> +			phys = <&phy_gmii_sel 2 0>;
>  		};
>  	};
>  
> @@ -114,11 +118,13 @@ Examples:
>  			phy-mode = "rgmii-txid";
>  			/* Filled in by U-Boot */
>  			mac-address = [ 00 00 00 00 00 00 ];
> +			phys = <&phy_gmii_sel 1 0>;
>  		};
>  		cpsw_emac1: slave@1 {
>  			phy_id = <&davinci_mdio>, <1>;
>  			phy-mode = "rgmii-txid";
>  			/* Filled in by U-Boot */
>  			mac-address = [ 00 00 00 00 00 00 ];
> +			phys = <&phy_gmii_sel 2 0>;
>  		};
>  	};
> -- 
> 2.10.5
>