Re: [PATCH V2 6/6] usb: host: Add ability to build new Broadcom STB USB drivers

[Alan Stern]

On Wed, 17 Oct 2018, Al Cooper wrote:

> Add the build system changes needed to get the Broadcom STB XHCI,
> EHCI and OHCI functionality working. The link order for XHCI was
> changed in the Makefile because of the way STB XHCI, EHCI and OHCI
> controllers share a port which requires that the XHCI driver be
> initialized first. Also update MAINTAINERS.
> 
> Signed-off-by: Al Cooper <alcooperx@xxxxxxxxx>
> ---
>  MAINTAINERS               |  9 +++++++++
>  drivers/usb/host/Kconfig  | 29 +++++++++++++++++++++++++++++
>  drivers/usb/host/Makefile | 18 ++++++++++++------
>  3 files changed, 50 insertions(+), 6 deletions(-)
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 6ac000cc006d..7e062dcbe173 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -3006,6 +3006,15 @@ S:	Supported
>  F:	drivers/gpio/gpio-brcmstb.c
>  F:	Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt
>  
> +BROADCOM BRCMSTB USB XHCI, EHCI and OHCI DRIVERS

This should say "XHCI and EHCI".  There is no Broadcom OHCI driver any 
more.

> +M:	Al Cooper <alcooperx@xxxxxxxxx>
> +L:	linux-usb@xxxxxxxxxxxxxxx
> +L:	bcm-kernel-feedback-list@xxxxxxxxxxxx
> +S:	Maintained
> +F:	drivers/usb/host/xhci-brcm.*
> +F:	drivers/usb/host/ohci-brcm.c

This should say "ehci-brcm.c".

> +F:	Documentation/devicetree/bindings/usb/brcm,bcm7445-*.txt
> +
>  BROADCOM BRCMSTB USB2 and USB3 PHY DRIVER
>  M:	Al Cooper <alcooperx@xxxxxxxxx>
>  L:	linux-kernel@xxxxxxxxxxxxxxx
> diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
> index 1a4ea98cac2a..112de3334389 100644
> --- a/drivers/usb/host/Kconfig
> +++ b/drivers/usb/host/Kconfig
> @@ -94,6 +94,35 @@ config USB_XHCI_TEGRA
>  	  Say 'Y' to enable the support for the xHCI host controller
>  	  found in NVIDIA Tegra124 and later SoCs.
>  
> +config USB_OHCI_BRCM
> +       tristate

This symbol is not used any more.

> +
> +config USB_EHCI_BRCM
> +       tristate
> +
> +config USB_XHCI_BRCM
> +       tristate
> +
> +config BRCM_USB_PHY
> +       tristate
> +
> +config USB_BRCM
> +	tristate "Broadcom STB USB support"
> +	depends on ARCH_BRCMSTB
> +	select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD
> +	select USB_EHCI_BRCM if USB_EHCI_HCD
> +	select USB_XHCI_BRCM if USB_XHCI_HCD
> +	select USB_XHCI_PLATFORM if USB_XHCI_HCD
> +	select BRCM_USB_PHY if USB_OHCI_HCD || USB_EHCI_HCD || USB_XHCI_HCD
> +	select GENERIC_PHY if BRCM_USB_PHY
> +	default ARCH_BRCMSTB
> +	help
> +	  Say Y to enable support for XHCI, EHCI and OHCI host controllers
> +	  found in Broadcom STB SoC's.
> +
> +	  Disabling this will keep the controllers and corresponding
> +	  PHYs powered down.
> +
>  endif # USB_XHCI_HCD
>  
>  config USB_EHCI_HCD

Alan Stern