Re: [PATCH v2 3/3] dt-bindings: iio: adc: Add docs for ad7124

[Jonathan Cameron]

On Fri, 19 Oct 2018 10:47:45 +0300
Stefan Popa <stefan.popa@xxxxxxxxxx> wrote:

> Add support for Analog Devices AD7124 4-channels and 8-channels ADC.
> 
> Signed-off-by: Stefan Popa <stefan.popa@xxxxxxxxxx>

I'm not certain on how to do reg for the channels.  Input from
Devicetree people please!

Given I would imagine this is very similar to some previous parts, it
might help to have a cross reference in the description.

Thanks,

Jonathan

> ---
> Changes in v2:
> 	- Nothing changed.
> 
>  .../devicetree/bindings/iio/adc/adi,ad7124.txt     | 96 ++++++++++++++++++++++
>  MAINTAINERS                                        |  1 +
>  2 files changed, 97 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad7124.txt
> 
> diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7124.txt b/Documentation/devicetree/bindings/iio/adc/adi,ad7124.txt
> new file mode 100644
> index 0000000..77a7b92
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7124.txt
> @@ -0,0 +1,96 @@
> +Analog Devices AD7124 ADC device driver
> +
> +Required properties for the AD7124:
> +	- compatible: Must be one of "adi,ad7124-4" or "adi,ad7124-8"
> +	- reg: SPI chip select number for the device
> +	- spi-max-frequency: Max SPI frequency to use
> +		see: Documentation/devicetree/bindings/spi/spi-bus.txt
> +	- clocks: phandle to the master clock (mclk)
> +		see: Documentation/devicetree/bindings/clock/clock-bindings.txt
> +	- clock-names: Must be "mclk".
> +	- interrupts: IRQ line for the ADC
> +		see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
> +
> +	- adi,channels: List of external channels connected to the ADC:
> +	  Required properties:
> +		* #address-cells: Must be 2.
> +		* #size-cells: Must be 0.
> +
> +	  The child nodes of this node represent the external channels which are
> +	  connected to the ADC.
> +
> +	  Each child node represents one channel and has the following
> +	  properties:
> +		Required properties:
> +			* reg: Pins the channel is connected to. The first value specifies
> +			  the positive input pin, the second value the negative input pin.
> +			* adi,channel-number: It can have up to 4 channels on ad7124-4 and
> +			  8 channels on ad7124-8, numbered from 0 to 15.
> +
> +		Optional properties:
> +			* adi,bipolar: If set the channel is used in bipolar mode.
> +			* adi,reference-select: Select the reference source to use when
> +			  converting on the the specific channel. Valid values are:
> +			  0: REFIN1(+)/REFIN1(â).
> +			  1: REFIN2(+)/REFIN2(â).
> +			  3: AVDD
> +			  If this field is left empty, internal reference is selected.
> +			* adi,gain: Select the gain when converting on the specific channel.
> +			  Valid values are: 1, 2, 4, 8, 16, 32, 64, 128.
> +			  If this field is left empty, gain of 1 is selected.
> +			* adi,odr-hz: The output data rate can be programmed from:
> +			  9 to 19200 for full power mode (when the master clock is 614.4 kHz)
> +			  2 to 4800 for mid power mode (when the master clock is 153.6 kHz)
> +			  1 to 2400 for low power mode (when the master clock is 76.8 kHz)
> +			  If this field is left empty, odr of 9 is selected.
> +
> +Optional properties:
> +	- refin1-supply: refin1 supply can be used as reference for conversion.
> +	- refin2-supply: refin2 supply can be used as reference for conversion.
> +	- avdd-supply: avdd supply can be used as reference for conversion.
> +
> +Example:
> +	adc@0 {
> +		compatible = "adi,ad7124-4";
> +		reg = <0>;
> +		spi-max-frequency = <5000000>;
> +		interrupts = <25 2>;
> +		interrupt-parent = <&gpio>;
> +		refin1-supply = <&adc_vref>;
> +		clocks = <&ad7124_mclk>;
> +		clock-names = "mclk";
> +
> +		adi,channels {
> +			#address-cells = <2>;
> +			#size-cells = <0>;
> +
> +			channel@0 {
> +				reg = <0 1>;
Normally we'd use the value of reg in the @.

I'm not actually sure what we do when there are two reg values
and they have no particular precedence.. Rob?

> +				adi,channel-number = <0>;
> +				adi,reference-select = <0>;
> +				adi,gain = <2>;
> +				adi,odr-hz = <10>;
> +			};
> +
> +			channel@1 {
> +				reg = <2 3>;
> +				adi,bipolar;
> +				adi,channel-number = <1>;
> +				adi,reference-select = <0>;
> +				adi,gain = <4>;
> +				adi,odr-hz = <50>;
> +			};
> +
> +			channel@2 {
> +				reg = <4 5>;
> +				adi,channel-number = <2>;
> +				adi,gain = <128>;
> +				adi,odr-hz = <19200>;
> +			};
> +
> +			channel@3 {
> +				reg = <6 7>;
> +				adi,channel-number = <3>;
> +			};
> +		};
> +	};
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 3a1bfcb..f2fa508 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -845,6 +845,7 @@ L:	linux-iio@xxxxxxxxxxxxxxx
>  W:	http://ez.analog.com/community/linux-device-drivers
>  S:	Supported
>  F:	drivers/iio/adc/ad7124.c
> +F:	Documentation/devicetree/bindings/iio/adc/adi,ad7124.txt
>  
>  ANALOG DEVICES INC AD9389B DRIVER
>  M:	Hans Verkuil <hans.verkuil@xxxxxxxxx>