RE: [PATCH 3/3] fpga manager: Adding FPGA Manager support for Xilinx zynqmp
From: Nava kishore Manne
Date: Mon Oct 22 2018 - 06:04:02 EST
Hi Mortiz,
Thanks for the quick response....
Please find my response inline.
> -----Original Message-----
> From: Moritz Fischer [mailto:moritz.fischer@xxxxxxxxx]
> Sent: Saturday, October 20, 2018 7:02 AM
> To: Moritz Fischer <moritz.fischer.private@xxxxxxxxx>
> Cc: Nava kishore Manne <navam@xxxxxxxxxx>; Alan Tull <atull@xxxxxxxxxx>;
> Rob Herring <robh+dt@xxxxxxxxxx>; Mark Rutland <mark.rutland@xxxxxxx>;
> Michal Simek <michals@xxxxxxxxxx>; Rajan Vaja <RAJANV@xxxxxxxxxx>; Jolly
> Shah <JOLLYS@xxxxxxxxxx>; linux-fpga@xxxxxxxxxxxxxxx; Devicetree List
> <devicetree@xxxxxxxxxxxxxxx>; linux-arm-kernel <linux-arm-
> kernel@xxxxxxxxxxxxxxxxxxx>; Linux Kernel Mailing List <linux-
> kernel@xxxxxxxxxxxxxxx>; chinnikishore369@xxxxxxxxx
> Subject: Re: [PATCH 3/3] fpga manager: Adding FPGA Manager support for
> Xilinx zynqmp
>
> On Fri, Oct 19, 2018 at 2:33 PM Moritz Fischer
> <moritz.fischer.private@xxxxxxxxx> wrote:
> >
> > Hi Nava,
> >
> > Looks good to me, a couple of nits inline below.
> >
> > On Fri, Oct 19, 2018 at 1:50 AM Nava kishore Manne
> > <nava.manne@xxxxxxxxxx> wrote:
> > >
> > > This patch adds FPGA Manager support for the Xilinx ZynqMp chip.
> >
> > Isn't it ZynqMP ?
> > >
> > > Signed-off-by: Nava kishore Manne <nava.manne@xxxxxxxxxx>
> > > ---
> > > Changes for v1:
> > > -None.
> > >
> > > Changes for RFC-V2:
> > > -Updated the Fpga Mgr registrations call's
> > > to 4.18
> > >
> > > drivers/fpga/Kconfig | 9 +++
> > > drivers/fpga/Makefile | 1 +
> > > drivers/fpga/zynqmp-fpga.c | 159
> > > +++++++++++++++++++++++++++++++++++++
> > > 3 files changed, 169 insertions(+)
> > > create mode 100644 drivers/fpga/zynqmp-fpga.c
> > >
> > > diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig index
> > > 1ebcef4bab5b..26ebbcf3d3a3 100644
> > > --- a/drivers/fpga/Kconfig
> > > +++ b/drivers/fpga/Kconfig
> > > @@ -56,6 +56,15 @@ config FPGA_MGR_ZYNQ_FPGA
> > > help
> > > FPGA manager driver support for Xilinx Zynq FPGAs.
> > >
> > > +config FPGA_MGR_ZYNQMP_FPGA
> > > + tristate "Xilinx Zynqmp FPGA"
> > > + depends on ARCH_ZYNQMP || COMPILE_TEST
> > > + help
> > > + FPGA manager driver support for Xilinx ZynqMP FPGAs.
> > > + This driver uses processor configuration port(PCAP)
> > This driver uses *the* processor configuration port.
> >
> > > + to configure the programmable logic(PL) through PS
> > > + on ZynqMP SoC.
> > > +
> > > config FPGA_MGR_XILINX_SPI
> > > tristate "Xilinx Configuration over Slave Serial (SPI)"
> > > depends on SPI
> > > diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile index
> > > 7a2d73ba7122..3488ebbaee46 100644
> > > --- a/drivers/fpga/Makefile
> > > +++ b/drivers/fpga/Makefile
> > > @@ -16,6 +16,7 @@ obj-$(CONFIG_FPGA_MGR_SOCFPGA_A10) +=
> socfpga-a10.o
> > > obj-$(CONFIG_FPGA_MGR_TS73XX) += ts73xx-fpga.o
> > > obj-$(CONFIG_FPGA_MGR_XILINX_SPI) += xilinx-spi.o
> > > obj-$(CONFIG_FPGA_MGR_ZYNQ_FPGA) += zynq-fpga.o
> > > +obj-$(CONFIG_FPGA_MGR_ZYNQMP_FPGA) += zynqmp-fpga.o
> > > obj-$(CONFIG_ALTERA_PR_IP_CORE) += altera-pr-ip-core.o
> > > obj-$(CONFIG_ALTERA_PR_IP_CORE_PLAT) += altera-pr-ip-core-plat.o
> > >
> > > diff --git a/drivers/fpga/zynqmp-fpga.c b/drivers/fpga/zynqmp-fpga.c
> > > new file mode 100644 index 000000000000..2760d7e3872a
> > > --- /dev/null
> > > +++ b/drivers/fpga/zynqmp-fpga.c
> > > @@ -0,0 +1,159 @@
> > > +// SPDX-License-Identifier: GPL-2.0+
> > > +/*
> > > + * Copyright (C) 2018 Xilinx, Inc.
> > > + */
> > > +
> > > +#include <linux/dma-mapping.h>
> > > +#include <linux/fpga/fpga-mgr.h>
> > > +#include <linux/io.h>
> > > +#include <linux/kernel.h>
> > > +#include <linux/module.h>
> > > +#include <linux/of_address.h>
> > > +#include <linux/string.h>
> > > +#include <linux/firmware/xlnx-zynqmp.h>
> > > +
> > > +/* Constant Definitions */
> > > +#define IXR_FPGA_DONE_MASK 0X00000008U
> > > +
> > > +/**
> > > + * struct zynqmp_fpga_priv - Private data structure
> > > + * @dev: Device data structure
> > > + * @flags: flags which is used to identify the bitfile type
> > > + */
> > > +struct zynqmp_fpga_priv {
> > > + struct device *dev;
> > > + u32 flags;
> > > +};
> > > +
> > > +static int zynqmp_fpga_ops_write_init(struct fpga_manager *mgr,
> > > + struct fpga_image_info *info,
> > > + const char *buf, size_t size)
> > > +{
> > > + struct zynqmp_fpga_priv *priv;
> > > +
> > > + priv = mgr->priv;
> > > + priv->flags = info->flags;
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int zynqmp_fpga_ops_write(struct fpga_manager *mgr,
> > > + const char *buf, size_t size) {
> > > + struct zynqmp_fpga_priv *priv;
> > > + char *kbuf;
> > > + dma_addr_t dma_addr;
> > > + int ret;
> > > + const struct zynqmp_eemi_ops *eemi_ops =
> > > +zynqmp_pm_get_eemi_ops();
> >
> > Reverse xmas-tree please, i.e. long lines first.
> >
> > > +
> > > + if (!eemi_ops || !eemi_ops->fpga_load)
> > > + return -ENXIO;
> > > +
> > > + priv = mgr->priv;
> > > +
> > > + kbuf = dma_alloc_coherent(priv->dev, size, &dma_addr,
> GFP_KERNEL);
> > > + if (!kbuf)
> > > + return -ENOMEM;
> > > +
> > > + memcpy(kbuf, buf, size);
> > > +
> > > + wmb(); /* ensure all writes are done before initiate FW call
> > > + */
> > > +
> > > + ret = eemi_ops->fpga_load(dma_addr, size, priv->flags);
>
> Don't you have to do anything with the flags? Is it really just a pass-through of
> FPGA manager flags to eemi calls?
>
> Don't you want to make partial bitstreams e.g. use a flags value that you export
> in your firmware header (xlnx-zynqmp.h) and set those based on what flags get
> passed in, i.e. explicitely translate FPGA Manager flags to your firmware flags?
At this point of time the firmware use Flag 0 for full Bitstream and 1 for partial bitstream loading.
So I have not doing any explicit translate FPGA Manager flags inside the driver.
Will document the flags info in xlnx-zynqmp.h
Regards,
Navakishore.