Re: [PATCH v5 3/5] dt-bindings: pinctrl: Add bindings for Actions Semi S700 SoC
From: Parthiban Nallathambi
Date: Tue Nov 06 2018 - 11:44:37 EST
ping on this patch series!
On 9/4/18 8:57 PM, Saravanan Sekar wrote:
On 08/29/18 17:50, Manivannan Sadhasivam wrote:
On Wed, Aug 29, 2018 at 10:24:11AM +0200, Saravanan Sekar wrote:
Add pinctrl and pio bindings for Actions Semi S700 SoC.
Signed-off-by: Parthiban Nallathambi <pn@xxxxxxx>
Signed-off-by: Saravanan Sekar <sravanhome@xxxxxxxxx>
Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
---
 .../bindings/pinctrl/actions,s700-pinctrl.txt | 170
+++++++++++++++++++++
 1 file changed, 170 insertions(+)
 create mode 100644
Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt
diff --git
a/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt
b/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt
new file mode 100644
index 000000000000..ceed32e836b1
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt
@@ -0,0 +1,170 @@
+Actions Semi S700 Pin Controller
+
+This binding describes the pin controller found in the S700 SoC.
+
+Required Properties:
+
+- compatible:ÂÂ Should be "actions,s700-pinctrl"
+- reg:ÂÂÂÂÂÂÂÂÂ Should contain the register base address and size of
+ÂÂÂÂÂÂÂ the pin controller.
+- clocks:ÂÂÂÂÂÂ phandle of the clock feeding the pin controller
+- gpio-controller: Marks the device node as a GPIO controller.
+- gpio-ranges: Specifies the mapping between gpio controller and
+ÂÂÂÂÂÂÂÂÂÂÂÂÂÂ pin-controller pins.
+- #gpio-cells: Should be two. The first cell is the gpio pin number
+ÂÂÂÂÂÂÂ and the second cell is used for optional parameters.
+- interrupt-controller: Marks the device node as an interrupt
controller.
+- #interrupt-cells: Specifies the number of cells needed to encode an
+ interrupt. Shall be set to 2. The first cell
+ÂÂÂÂÂÂÂ defines the interrupt number, the second encodes
+ÂÂÂÂÂÂÂ the trigger flags described in
+ÂÂÂÂÂÂÂ bindings/interrupt-controller/interrupts.txt
+- interrupts: The interrupt outputs from the controller. There is
one GPIO
+ÂÂÂÂÂÂÂÂÂÂÂÂÂ interrupt per GPIO bank. The number of interrupts
listed depends
+ÂÂÂÂÂÂÂÂÂÂÂÂÂ on the number of GPIO banks on the SoC. The interrupts
must be
+ÂÂÂÂÂÂÂÂÂÂÂÂÂ ordered by bank, starting with bank 0.
+
+Please refer to pinctrl-bindings.txt in this directory for details
of the
+common pinctrl bindings used by client devices, including the
meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an arbitrary
number of
+subnodes. Each of these subnodes represents some desired
configuration for a
+pin, a group, or a list of pins or groups. This configuration can
include the
+mux function to select on those group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+PIN CONFIGURATION NODES:
+
+The name of each subnode is not important; all subnodes should be
enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly
listed. In
+other words, a subnode that lists a mux function but no pin
configuration
+parameters implies no information about any pin configuration
parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+Pinmux functions are available only for the pin groups while pinconf
+parameters are available for both pin groups and individual pins.
+
+The following generic properties as defined in pinctrl-bindings.txt
are valid
+to specify in a pin configuration subnode:
+
+Required Properties:
+
+- pins:ÂÂÂÂÂÂÂ An array of strings, each string containing the name
of a pin.
+ÂÂÂÂÂÂÂ These pins are used for selecting the pull control and schmitt
+ÂÂÂÂÂÂÂ trigger parameters. The following are the list of pins
+ÂÂÂÂÂÂÂ available:
+
+ÂÂÂÂÂÂÂ eth_txd0, eth_txd1, eth_txd2, eth_txd3, eth_txen, eth_rxer,
+ÂÂÂÂÂÂÂ eth_crs_dv, eth_rxd1, eth_rxd0, eth_rxd2, eth_rxd3,
eth_ref_clk,
+ÂÂÂÂÂÂÂ eth_mdc, eth_mdio, sirq0, sirq1, sirq2, i2s_d0, i2s_bclk0,
+ÂÂÂÂÂÂÂ i2s_lrclk0, i2s_mclk0, i2s_d1, i2s_bclk1, i2s_lrclk1,
i2s_mclk1,
+ÂÂÂÂÂÂÂ pcm1_in, pcm1_clk, pcm1_sync, pcm1_out, ks_in0, ks_in1, ks_in2,
+ÂÂÂÂÂÂÂ ks_in3, ks_out0, ks_out1, ks_out2, lvds_oep, lvds_oen,
lvds_odp,
+ÂÂÂÂÂÂÂ lvds_odn, lvds_ocp, lvds_ocn, lvds_obp, lvds_obn, lvds_oap,
+ÂÂÂÂÂÂÂ lvds_oan, lvds_eep, lvds_een, lvds_edp, lvds_edn, lvds_ecp,
+ÂÂÂÂÂÂÂ lvds_ecn, lvds_ebp, lvds_ebn, lvds_eap, lvds_ean, lcd0_d18,
+ÂÂÂÂÂÂÂ lcd0_d2, dsi_dp3, dsi_dn3, dsi_dp1, dsi_dn1, dsi_cp, dsi_cn,
+ÂÂÂÂÂÂÂ dsi_dp0, dsi_dn0, dsi_dp2, dsi_dn2, sd0_d0, sd0_d1, sd0_d2,
+ÂÂÂÂÂÂÂ sd0_d3, sd1_d0, sd1_d1, sd1_d2, sd1_d3, sd0_cmd, sd0_clk,
+ÂÂÂÂÂÂÂ sd1_cmd, sd1_clk, spi0_ss, spi0_miso, uart0_rx, uart0_tx,
+ÂÂÂÂÂÂÂ uart2_rx, uart2_tx, uart2_rtsb, uart2_ctsb, uart3_rx, uart3_tx,
+ÂÂÂÂÂÂÂ uart3_rtsb, uart3_ctsb, i2c0_sclk, i2c0_sdata, i2c1_sclk,
+ÂÂÂÂÂÂÂ i2c1_sdata, i2c2_sdata, csi_dn0, csi_dp0, csi_dn1, csi_dp1,
+ÂÂÂÂÂÂÂ csi_cn, csi_cp, csi_dn2, csi_dp2, csi_dn3, csi_dp3,
+ÂÂÂÂÂÂÂ sensor0_pclk, sensor0_ckout, dnand_d0, dnand_d1, dnand_d2,
+ÂÂÂÂÂÂÂ dnand_d3, dnand_d4, dnand_d5, dnand_d6, dnand_d7, dnand_wrb,
+ÂÂÂÂÂÂÂ dnand_rdb, dnand_rdbn, dnand_dqs, dnand_dqsn, dnand_rb0,
+ÂÂÂÂÂÂÂ dnand_ale, dnand_cle, dnand_ceb0, dnand_ceb1, dnand_ceb2,
+ÂÂÂÂÂÂÂ dnand_ceb3, porb, clko_25m, bsel, pkg0, pkg1, pkg2, pkg3
+
+- groups:ÂÂÂÂÂÂ An array of strings, each string containing the name
of a pin
+ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ group. These pin groups are used for selecting the
pinmux
+ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ functions.
+ÂÂÂÂÂÂÂ rgmii_txd23_mfp, rgmii_rxd2_mfp, rgmii_rxd3_mfp, lcd0_d18_mfp,
+ÂÂÂÂÂÂÂ rgmii_txd01_mfp, rgmii_txd0_mfp, rgmii_txd1_mfp,
rgmii_txen_mfp,
+ÂÂÂÂÂÂÂ rgmii_rxen_mfp, rgmii_rxd1_mfp, rgmii_rxd0_mfp,
rgmii_ref_clk_mfp,
+ÂÂÂÂÂÂÂ i2s_d0_mfp, i2s_pcm1_mfp, i2s0_pcm0_mfp, i2s1_pcm0_mfp,
+ÂÂÂÂÂÂÂ i2s_d1_mfp, ks_in2_mfp, ks_in1_mfp, ks_in0_mfp, ks_in3_mfp,
+ÂÂÂÂÂÂÂ ks_out0_mfp, ks_out1_mfp, ks_out2_mfp, lvds_o_pn_mfp,
dsi_dn0_mfp,
+ÂÂÂÂÂÂÂ dsi_dp2_mfp, lcd0_d2_mfp, dsi_dp3_mfp, dsi_dn3_mfp,
dsi_dp0_mfp,
+ÂÂÂÂÂÂÂ lvds_ee_pn_mfp, uart2_rx_tx_mfp, spi0_i2c_pcm_mfp,
dsi_dnp1_cp_d2_mfp,
+ÂÂÂÂÂÂÂ dsi_dnp1_cp_d17_mfp, lvds_e_pn_mfp, dsi_dn2_mfp,
uart2_rtsb_mfp,
+ÂÂÂÂÂÂÂ uart2_ctsb_mfp, uart3_rtsb_mfp, uart3_ctsb_mfp, sd0_d0_mfp,
sd0_d1_mfp,
+ÂÂÂÂÂÂÂ sd0_d2_d3_mfp, sd1_d0_d3_mfp, sd0_cmd_mfp, sd0_clk_mfp,
sd1_cmd_mfp,
+ÂÂÂÂÂÂÂ uart0_rx_mfp, clko_25m_mfp, csi_cn_cp_mfp, sens0_ckout_mfp,
uart0_tx_mfp,
+ÂÂÂÂÂÂÂ i2c0_mfp, csi_dn_dp_mfp, sen0_pclk_mfp, pcm1_in_mfp,
pcm1_clk_mfp,
+ÂÂÂÂÂÂÂ pcm1_sync_mfp, pcm1_out_mfp, dnand_data_wr_mfp,
dnand_acle_ce0_mfp,
+ÂÂÂÂÂÂÂ nand_ceb2_mfp, nand_ceb3_mfp
+
+ÂÂÂÂÂÂÂ These pin groups are used for selecting the drive strength
+ÂÂÂÂÂÂÂ parameters.
+
+ÂÂÂÂÂÂÂ sirq_drv, rgmii_txd23_drv, rgmii_rxd23_drv,
rgmii_txd01_txen_drv,
+ÂÂÂÂÂÂÂ rgmii_rxer_drv, rgmii_crs_drv, rgmii_rxd10_drv,
rgmii_ref_clk_drv,
+ÂÂÂÂÂÂÂ smi_mdc_mdio_drv, i2s_d0_drv, i2s_bclk0_drv, i2s3_drv,
i2s13_drv,
+ÂÂÂÂÂÂÂ pcm1_drv, ks_in_drv, ks_out_drv, lvds_all_drv, lcd_d18_d2_drv,
+ÂÂÂÂÂÂÂ dsi_all_drv, sd0_d0_d3_drv, sd0_cmd_drv, sd0_clk_drv,
spi0_all_drv,
+ÂÂÂÂÂÂÂ uart0_rx_drv, uart0_tx_drv, uart2_all_drv, i2c0_all_drv,
i2c12_all_drv,
+ÂÂÂÂÂÂÂ sens0_pclk_drv, sens0_ckout_drv, uart3_all_drv
+
+- function:ÂÂÂ An array of strings, each string containing the name
of the
+ÂÂÂÂÂÂÂ pinmux functions. These functions can only be selected by
+ÂÂÂÂÂÂÂ the corresponding pin groups. The following are the list of
+ÂÂÂÂÂÂÂ pinmux functions available:
+
+ÂÂÂÂÂÂÂ nor, eth_rgmii, eth_sgmii, spi0, spi1, spi2, spi3, seNs0,
sens1,
+ÂÂÂÂÂÂÂ uart0, uart1, uart2, uart3, uart4, uart5, uart6, i2s0, i2s1,
+ÂÂÂÂÂÂÂ pcm1, pcm0, ks, jtag, pwm0, pwm1, pwm2, pwm3, pwm4, pwm5, p0,
+ÂÂÂÂÂÂÂ sd0, sd1, sd2, i2c0, i2c1, i2c2, i2c3, dsi, lvds, usb30,
+ÂÂÂÂÂÂÂ clko_25m, mipi_csi, nand, spdif, sirq0, sirq1, sirq2, bt, lcd0
+
+Optional Properties:
+
+- bias-pull-down: No arguments. The specified pins should be
configured as
+ÂÂÂÂÂÂÂ pull down.
+- bias-pull-up:ÂÂ No arguments. The specified pins should be
configured as
+ÂÂÂÂÂÂÂ pull up.
+- input-schmitt-enable: No arguments: Enable schmitt trigger for the
specified
+ÂÂÂÂÂÂÂ pins
+- input-schmitt-disable: No arguments: Disable schmitt trigger for
the specified
+ÂÂÂÂÂÂÂ pins
+- drive-strength: Integer. Selects the drive strength for the specified
+ÂÂÂÂÂÂÂ pins in mA.
+ÂÂÂÂÂÂÂ Valid values are:
+ÂÂÂÂÂÂÂ <2>
+ÂÂÂÂÂÂÂ <4>
+ÂÂÂÂÂÂÂ <8>
+ÂÂÂÂÂÂÂ <12>
+
+Example:
+
+ÂÂÂ pinctrl: pinctrl@e01b0000 {
+ÂÂÂÂÂÂÂ compatible = "actions,s700-pinctrl";
+ÂÂÂÂÂÂÂ reg = <0x0 0xe01b0000 0x0 0x1000>;
+ÂÂÂÂÂÂÂ clocks = <&cmu CLK_GPIO>;
+ÂÂÂÂÂÂÂ gpio-controller;
+ÂÂÂÂÂÂÂ gpio-ranges = <&pinctrl 0 0 136>;
Not sure about this pin count. As per my datasheet, only 122 pins
are available. More justification will be provided in driver patch.
Datasheet is incomplete and ranges mentioned as reserved are still used
in the driver code (directly referred from actions kernel tree)
+ÂÂÂÂÂÂÂ #gpio-cells = <2>;
+ÂÂÂÂÂÂÂ interrupt-controller;
+ÂÂÂÂÂÂÂ #interrupt-cells = <2>;
+ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>,
+ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>,
+ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>,
+ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
+ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>
Missing semicolon.
Regards,
Mani
+
+ÂÂÂÂÂÂÂ uart3-default: uart3-default {
+ÂÂÂÂÂÂÂÂÂÂÂ pinmux {
+ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ groups = "uart3_rtsb_mfp", "uart3_ctsb_mfp";
+ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ function = "uart3";
+ÂÂÂÂÂÂÂÂÂÂÂ };
+ÂÂÂÂÂÂÂÂÂÂÂ pinconf {
+ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ groups = "uart3_all_drv";
+ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ drive-strength = <2>;
+ÂÂÂÂÂÂÂÂÂÂÂ };
+ÂÂÂÂÂÂÂ };
+ÂÂÂ };
--
2.14.4
--
Thanks,
Parthiban N
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-22 Fax: (+49)-8142-66989-80 Email: pn@xxxxxxx