RE: [LINUX PATCH v12 1/3] dt-bindings: mtd: arasan: Add device tree binding documentation

[Naga Sureshkumar Relli]

Hi,

> -----Original Message-----
> From: Michal Simek [mailto:michal.simek@xxxxxxxxxx]
> Sent: Friday, November 16, 2018 6:04 PM
> To: Martin Lund <martin.lund@xxxxxxxxxxxxxxxxxx>; Naga Sureshkumar Relli
> <nagasure@xxxxxxxxxx>
> Cc: boris.brezillon@xxxxxxxxxxx; miquel.raynal@xxxxxxxxxxx; richard@xxxxxx; David
> Woodhouse <dwmw2@xxxxxxxxxxxxx>; Brian Norris <computersforpeace@xxxxxxxxx>; Marek
> VaÅut <marek.vasut@xxxxxxxxx>; naga sureshkumar <nagasuresh12@xxxxxxxxx>; linux-
> mtd@xxxxxxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx; robh@xxxxxxxxxx
> Subject: Re: [LINUX PATCH v12 1/3] dt-bindings: mtd: arasan: Add device tree binding
> documentation
> 
> On 16. 11. 18 12:50, Martin Lund wrote:
> > Hi Naga,
> >
> > I've been working on running up the latest kernel (v4.20-rc2) on our
> > custom Xilinx hw board so that I can test the v12 version of your
> > Arasan nand driver.
> >
> > I've managed to get the driver successfully up and running and ready
> > for testing with a Micron MT29F64G08AFAAAWP device. However, setting
> > it up I've found a few inaccuracies in the documentation of the device
> > tree bindings.
> >
> > This is the device configuration that ended up working for me with
> > linux v4.20-rc2:
> >
> >        nfc: nand@ff100000 {
> >             compatible = "xlnx,zynqmp-nand", "arasan,nfc-v3p10";
> >             reg = <0x0 0xff100000 0x0 0x1000>;
> >             clock-names = "clk_sys", "clk_flash";
> >             clocks = <&clk200>, <&clk100>;
> >             interrupt-parent = <&gic>;
> >             interrupts = <0 14 4>;
> >             #address-cells = <1>;
> >             #size-cells = <0>;
> >
> >             nand@0 {
> >                 reg = <0>;
> >                 nand-ecc-mode = "hw";
> >             };
> >         };
> >
> > Compared with the example you will notice that "clock-name" should be
> > "clock-names". reg was missing a "0x0".
> 
> clock-names and even that names - you are right it is not correct and should be fixed.
Clock-names I will change from "clock-name" to "clock-names".
But I got some review comments previously, to use "sys" instead of  "clk_sys" and "flash" instead of "clk_flash".
And I have to change this in driver.
I will update that.

Thanks,
Naga Sureshkumar Relli

> 
> Missing 0x0 in reg doesn't matter because it depends on address/size cells.
> 
> > I think it is helpful to provide a real-world working example, so you
> > might also consider changing the example "clocks" configuration to
> > clk200/clk100 since there is no clk_misc among the clock sources of
> > any of the xilinx zynqmp board device tree configurations.
> 
> Real example is the best normally just c&p from existing dts is the way to go.
> But in connection to clocks it doesn't matter what exactly should be there and I don't think
> there is any consistency in that. Hopefully this will be removed by yaml conversion.
> 
> Thanks,
> Michal