[PATCH 06/14] dt-bindings: clock: milbeaut: add Milbeaut clock description

[Sugaya Taichi]

Add DT bindings document for Milbeaut clock.

Signed-off-by: Sugaya Taichi <sugaya.taichi@xxxxxxxxxxxxx>
---
 .../devicetree/bindings/clock/milbeaut-clock.txt   | 93 ++++++++++++++++++++++
 1 file changed, 93 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/clock/milbeaut-clock.txt

diff --git a/Documentation/devicetree/bindings/clock/milbeaut-clock.txt b/Documentation/devicetree/bindings/clock/milbeaut-clock.txt
new file mode 100644
index 0000000..5c093c8
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/milbeaut-clock.txt
@@ -0,0 +1,93 @@
+Milbeaut M10V Clock Controller Binding
+----------------------------------------
+Milbeaut clock controller is consists of few oscillators, PLL, multiplexer
+and few divider modules
+
+This binding uses common clock bindings
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Required properties:
+- compatible: shall be "socionext,milbeaut-m10v-clk-regs"
+- reg: shall contain base address and length of clock registers
+- #clock-cells: shall be 0
+
+Example:
+	m10v-clk-tree@ {
+		compatible = "socionext,milbeaut-m10v-clk-regs";
+		reg = <0x1d021000 0x4000>;
+
+		clocks {
+			#address-cells = <0>;
+			#size-cells = <0>;
+
+			uclk40xi: uclk40xi {
+				compatible = "fixed-clock";
+				#clock-cells = <0>;
+				clock-frequency = <40000000>;
+			};
+		};
+	}
+
+The clock consumer shall specify the desired clock-output of the clock
+controller (as defined in [2]) by specifying output-id in its "clock"
+phandle cell
+[2] arch/arm/boot/dts/milbeaut-m10v-clk.h
+
+For example for UART1:
+	usio1:  usio_uart@1e700010 {
+		index = <0>;
+		compatible = "socionext,milbeaut-m10v-usio-uart";
+		reg = <0x1e700010 0x10>;
+		interrupts = <0 141 0x4>, <0 149 0x4>;
+		interrupt-names = "rx", "tx";
+		clocks = <&hclk>;
+	};
+
+
+
+
+Required properties:
+- compatible:
+	"socionext,milbeaut-m10v-clk-mux"
+		-clock-cells: should be 0
+		-clocks: should be two factor
+	"socionext,milbeaut-m10v-pll-fixed-factor"
+		-clock-cells: should be 0
+		-clocks: should be one factor
+		-offset: offset
+		-clock-div: div number
+		-clock-mult: multiple number
+	"socionext,milbeaut-m10v-clk-div"
+		-clock-cells: should be 0
+		-clocks: should be one factor
+		-offset: offset
+		-mask: mask bit
+		-ratios: div ratio
+
+Example
+	piclk_mux_0: spiclk_mux_0 {
+		compatible = "socionext,m10v-clk-div";
+		#clock-cells = <0>;
+		clocks = <&pll10_div_1_2>;
+		offset = <bSPICLK>;
+		mask = <0x3>;
+		ratios = <4 0x5 2 0x4>;
+	};
+
+	pll10: pll10 {
+		compatible = "socionext,m10v-pll-fixed-factor";
+		#clock-cells = <0>;
+		clocks = <&uclk40xi>;
+		offset = <10>;
+		clock-div = <5>;
+		clock-mult = <108>;
+	};
+
+	emmcclk: emmcclk {
+		compatible = "socionext,m10v-clk-div";
+		#clock-cells = <0>;
+		clocks = <&pll11>;
+		offset = <bEMMCCLK>;
+		mask = <0x3>;
+		ratios = <15 0x7 10 0x6 9 0x5 8 0x4>;
+	};
-- 
1.9.1