Re: [PATCH 1/1] reset: imx7: Add support for i.MX8MQ

From: Andrey Smirnov
Date: Mon Nov 26 2018 - 10:59:55 EST

Next message: Hans Verkuil: "Re: [PATCH v3] media: venus: amend buffer size for bitstream plane"
Previous message: Avri Altman: "RE: [PATCH] scsi: ufs: add fall through annotation"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On Mon, Nov 19, 2018 at 6:32 AM Philipp Zabel <p.zabel@xxxxxxxxxxxxxx> wrote:
>
> Hi Andrey,
>
> thank you for the patch.
>
> In general, sharing the lookup table with i.MX7 is fine iff it is a
> strict superset. But I don't think that is the case (see below).
> Even so, this will change if there ever is another i.MX7 or i.MX8M
> variant that is also a superset of i.MX7, but not a superset of
> i.MX8M. Also, just listing all resets in order of appearance would make
> review a bit easier.
>
> I don't like increasing IMX7_RESET_NUM though, i.MX8M should have its
> own nr_resets.
>
> On Sat, 2018-11-17 at 10:11 -0800, Andrey Smirnov wrote:
> > SRC IP block used in i.MX8MQ is a superset of what is found in i.MX7D,
>
> Is this true, though?
>
> i.MX7 has SRC_ERCR at offset 0x14 and HSICPHY_RCR at offset 0x1c.
> According to documentation, i.MX8M is missing those at least.
>

OK, I'll convert the patch to use separate LUTs in v2.

> > so add all of the definitions necessary to support both.
> >
> > Cc: p.zabel@xxxxxxxxxxxxxx
> > Cc: Fabio Estevam <fabio.estevam@xxxxxxx>
> > Cc: cphealy@xxxxxxxxx
> > Cc: l.stach@xxxxxxxxxxxxxx
> > Cc: Leonard Crestez <leonard.crestez@xxxxxxx>
> > Cc: "A.s. Dong" <aisheng.dong@xxxxxxx>
> > Cc: Richard Zhu <hongxing.zhu@xxxxxxx>
> > Cc: linux-imx@xxxxxxx
> > Cc: linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> > Cc: linux-kernel@xxxxxxxxxxxxxxx
> > Signed-off-by: Andrey Smirnov <andrew.smirnov@xxxxxxxxx>
> > ---
> > drivers/reset/Kconfig | 2 +-
> > drivers/reset/reset-imx7.c | 66 ++++++++++++++++++++++++-
> > include/dt-bindings/reset/imx7-reset.h | 15 +++++-
> > include/dt-bindings/reset/imx8m-reset.h | 47 ++++++++++++++++++
> > 4 files changed, 127 insertions(+), 3 deletions(-)
> > create mode 100644 include/dt-bindings/reset/imx8m-reset.h
> >
> > diff --git a/drivers/reset/Kconfig b/drivers/reset/Kconfig
> > index c21da9fe51ec..4909aab7401b 100644
> > --- a/drivers/reset/Kconfig
> > +++ b/drivers/reset/Kconfig
> > @@ -50,7 +50,7 @@ config RESET_HSDK
> > config RESET_IMX7
> > bool "i.MX7 Reset Driver" if COMPILE_TEST
> > depends on HAS_IOMEM
> > - default SOC_IMX7D
> > + default SOC_IMX7D || SOC_IMX8MQ
> > select MFD_SYSCON
> > help
> > This enables the reset controller driver for i.MX7 SoCs.
> > diff --git a/drivers/reset/reset-imx7.c b/drivers/reset/reset-imx7.c
> > index 77911fa8f31d..dffad618f805 100644
> > --- a/drivers/reset/reset-imx7.c
> > +++ b/drivers/reset/reset-imx7.c
> > @@ -21,14 +21,16 @@
> > #include <linux/reset-controller.h>
> > #include <linux/regmap.h>
> > #include <dt-bindings/reset/imx7-reset.h>
> > +#include <dt-bindings/reset/imx8m-reset.h>
> >
> > struct imx7_src {
> > struct reset_controller_dev rcdev;
> > struct regmap *regmap;
> > };
> >
> > -enum imx7_src_registers {
> > +enum imx_src_registers {
> > SRC_A7RCR0 = 0x0004,
> > + SRC_A53RCR0 = 0x0004,
> > SRC_M4RCR = 0x000c,
> > SRC_ERCR = 0x0014,
> > SRC_HSICPHY_RCR = 0x001c,
> > @@ -36,7 +38,9 @@ enum imx7_src_registers {
> > SRC_USBOPHY2_RCR = 0x0024,
> > SRC_MIPIPHY_RCR = 0x0028,
> > SRC_PCIEPHY_RCR = 0x002c,
>
> These aren't complete. I see at least SRC_HDMI_RCR, SRC_DISP_RCR,
> SRC_GPU_RCR, and SRC_VPU_RCR missing.
>
> > + SRC_PCIE2PHY_RCR = 0x0048,
>
> And SRC_MIPIPHY1_RCR, SRC_MIPIPHY2_RCR. Please check the reference
> manual and complete the list of registers that contain resets.
>
> > SRC_DDRC_RCR = 0x1000,
> > +
>
> Whitespace.
>
> > };
> >
> > struct imx7_src_signal {
> > @@ -67,11 +71,67 @@ static const struct imx7_src_signal imx7_src_signals[IMX7_RESET_NUM] = {
> > [IMX7_RESET_PCIEPHY] = { SRC_PCIEPHY_RCR, BIT(2) | BIT(1) },
> > [IMX7_RESET_PCIEPHY_PERST] = { SRC_PCIEPHY_RCR, BIT(3) },
> > [IMX7_RESET_PCIE_CTRL_APPS_EN] = { SRC_PCIEPHY_RCR, BIT(6) },
> > + [IMX7_RESET_PCIE_CTRL_APPS_CLK_REQ] = { SRC_PCIEPHY_RCR, BIT(4) },
>
> Now I feel like CTRL_APPS_EN shouldn't have been added here either. But
> while there I wasn't really sure about whether that is actually a valid
> reset, I'm pretty sure that this one isn't.
> I think that i.MX8M either needs a clock driver to control this bit and
> the corresponding IOMUXC GPR bit to enable the PCIe refclk, or the PCIe
> driver has to access this register via syscon. I really don't want to
> see a clock enable signal described in the device tree as a reset.
>

OK, will drop in v2.

> > [IMX7_RESET_PCIE_CTRL_APPS_TURNOFF] = { SRC_PCIEPHY_RCR, BIT(11) },
> > [IMX7_RESET_DDRC_PRST] = { SRC_DDRC_RCR, BIT(0) },
> > [IMX7_RESET_DDRC_CORE_RST] = { SRC_DDRC_RCR, BIT(1) },
> > +
> > + [IMX8M_RESET_A53_CORE_POR_RESET2] = { SRC_A53RCR0, BIT(2) },
> > + [IMX8M_RESET_A53_CORE_POR_RESET3] = { SRC_A53RCR0, BIT(3) },
> > + [IMX8M_RESET_A53_CORE_RESET2] = { SRC_A53RCR0, BIT(6) },
> > + [IMX8M_RESET_A53_CORE_RESET3] = { SRC_A53RCR0, BIT(7) },
>
> Missing IMX8M_RESET_A53_DBG_RESET2,3.
>
> > + [IMX8M_RESET_A53_ETM_RESET2] = { SRC_A53RCR0, BIT(14) },
> > + [IMX8M_RESET_A53_ETM_RESET3] = { SRC_A53RCR0, BIT(15) },
>
> Missing some reset registers here.
>
> > + [IMX8M_RESET_PCIE2PHY] = { SRC_PCIEPHY_RCR, BIT(2) | BIT(1) },
> > + [IMX8M_RESET_PCIE2PHY_PERST] = { SRC_PCIE2PHY_RCR, BIT(3) },
> > + [IMX8M_RESET_PCIE2_CTRL_APPS_EN] = { SRC_PCIE2PHY_RCR, BIT(6) },
> > + [IMX8M_RESET_PCIE2_CTRL_APPS_CLK_REQ] = { SRC_PCIE2PHY_RCR, BIT(4) },
>
> See above.
>
> > + [IMX8M_RESET_PCIE2_CTRL_APPS_TURNOFF] = { SRC_PCIE2PHY_RCR, BIT(11) },
>
> Missing some reset registers here.
>
> > };
> >
> > +static inline void imx7_src_check_definitions(void)
> > +{
> > + BUILD_BUG_ON(IMX8M_RESET_A53_CORE_POR_RESET0 !=
> > + IMX7_RESET_A7_CORE_POR_RESET0);
> > + BUILD_BUG_ON(IMX8M_RESET_A53_CORE_POR_RESET1 !=
> > + IMX7_RESET_A7_CORE_POR_RESET1);
> > + BUILD_BUG_ON(IMX8M_RESET_A53_CORE_RESET0 !=
> > + IMX7_RESET_A7_CORE_RESET0);
> > + BUILD_BUG_ON(IMX8M_RESET_A53_CORE_RESET1 !=
> > + IMX7_RESET_A7_CORE_RESET1);
> > + BUILD_BUG_ON(IMX8M_RESET_A53_DBG_RESET0 !=
> > + IMX7_RESET_A7_DBG_RESET0);
> > + BUILD_BUG_ON(IMX8M_RESET_A53_DBG_RESET1 !=
> > + IMX7_RESET_A7_DBG_RESET1);
> > + BUILD_BUG_ON(IMX8M_RESET_A53_ETM_RESET0 !=
> > + IMX7_RESET_A7_ETM_RESET0);
> > + BUILD_BUG_ON(IMX8M_RESET_A53_ETM_RESET1 !=
> > + IMX7_RESET_A7_ETM_RESET1);
> > + BUILD_BUG_ON(IMX8M_RESET_A53_SOC_DBG_RESET !=
> > + IMX7_RESET_A7_SOC_DBG_RESET);
> > + BUILD_BUG_ON(IMX8M_RESET_A53_L2RESET != IMX7_RESET_A7_L2RESET);
> > + BUILD_BUG_ON(IMX8M_RESET_SW_M4C_RST != IMX7_RESET_SW_M4C_RST);
> > + BUILD_BUG_ON(IMX8M_RESET_SW_M4P_RST != IMX7_RESET_SW_M4P_RST);
> > + BUILD_BUG_ON(IMX8M_RESET_EIM_RST != IMX7_RESET_EIM_RST);
> > + BUILD_BUG_ON(IMX8M_RESET_HSICPHY_PORT_RST !=
> > + IMX7_RESET_HSICPHY_PORT_RST);
> > + BUILD_BUG_ON(IMX8M_RESET_USBPHY1_POR != IMX7_RESET_USBPHY1_POR);
> > + BUILD_BUG_ON(IMX8M_RESET_USBPHY1_PORT_RST !=
> > + IMX7_RESET_USBPHY1_PORT_RST);
> > + BUILD_BUG_ON(IMX8M_RESET_USBPHY2_POR != IMX7_RESET_USBPHY2_POR);
> > + BUILD_BUG_ON(IMX8M_RESET_USBPHY2_PORT_RST !=
> > + IMX7_RESET_USBPHY2_PORT_RST);
> > + BUILD_BUG_ON(IMX8M_RESET_MIPI_PHY_MRST != IMX7_RESET_MIPI_PHY_MRST);
> > + BUILD_BUG_ON(IMX8M_RESET_MIPI_PHY_SRST != IMX7_RESET_MIPI_PHY_SRST);
> > + BUILD_BUG_ON(IMX8M_RESET_PCIEPHY != IMX7_RESET_PCIEPHY);
> > + BUILD_BUG_ON(IMX8M_RESET_PCIE_CTRL_APPS_EN !=
> > + IMX7_RESET_PCIE_CTRL_APPS_EN);
> > + BUILD_BUG_ON(IMX8M_RESET_PCIE_CTRL_APPS_TURNOFF !=
> > + IMX7_RESET_PCIE_CTRL_APPS_TURNOFF);
> > + BUILD_BUG_ON(IMX8M_RESET_DDRC_PRST != IMX7_RESET_DDRC_PRST);
> > + BUILD_BUG_ON(IMX8M_RESET_DDRC_CORE_RST != IMX7_RESET_DDRC_CORE_RST);
> > +}
>
> This won't be necessary with a separate lookup table.
>
> > static struct imx7_src *to_imx7_src(struct reset_controller_dev *rcdev)
> > {
> > return container_of(rcdev, struct imx7_src, rcdev);
> > @@ -85,6 +145,7 @@ static int imx7_reset_set(struct reset_controller_dev *rcdev,
> > unsigned int value = assert ? signal->bit : 0;
> >
> > switch (id) {
> > + case IMX8M_RESET_PCIE2PHY: /* FALLTHROUGH */
>
> I'd prefer lowercase /* fallthrough */.
>
> > case IMX7_RESET_PCIEPHY:
> > /*
> > * wait for more than 10us to release phy g_rst and
> > @@ -94,6 +155,7 @@ static int imx7_reset_set(struct reset_controller_dev *rcdev,
> > udelay(10);
> > break;
> >
> > + case IMX8M_RESET_PCIE2_CTRL_APPS_EN: /* FALLTHROUGH */
>
> And here.
>
> > case IMX7_RESET_PCIE_CTRL_APPS_EN:
> > value = (assert) ? 0 : signal->bit;
> > break;
> > @@ -126,6 +188,8 @@ static int imx7_reset_probe(struct platform_device *pdev)
> > struct device *dev = &pdev->dev;
> > struct regmap_config config = { .name = "src" };
> >
> > + imx7_src_check_definitions();
> > +
> > imx7src = devm_kzalloc(dev, sizeof(*imx7src), GFP_KERNEL);
> > if (!imx7src)
> > return -ENOMEM;
> > diff --git a/include/dt-bindings/reset/imx7-reset.h b/include/dt-bindings/reset/imx7-reset.h
> > index 31b3f87dde9a..8fefd694d481 100644
> > --- a/include/dt-bindings/reset/imx7-reset.h
> > +++ b/include/dt-bindings/reset/imx7-reset.h
> > @@ -57,8 +57,21 @@
> > #define IMX7_RESET_DDRC_CORE_RST 24
> >
> > #define IMX7_RESET_PCIE_CTRL_APPS_TURNOFF 25
> > +#define IMX7_RESET_PCIE_CTRL_APPS_CLK_REQ 26
>
> See above.
>
> > -#define IMX7_RESET_NUM 26
>
> Please leave this at 26.
>
> > +#define IMX8M_RESET_A53_CORE_POR_RESET2 27
> > +#define IMX8M_RESET_A53_CORE_POR_RESET3 28
> > +#define IMX8M_RESET_A53_CORE_RESET2 29
> > +#define IMX8M_RESET_A53_CORE_RESET3 30
> > +#define IMX8M_RESET_A53_ETM_RESET2 31
> > +#define IMX8M_RESET_A53_ETM_RESET3 32
> > +#define IMX8M_RESET_PCIE2PHY 33
> > +#define IMX8M_RESET_PCIE2PHY_PERST 34
> > +#define IMX8M_RESET_PCIE2_CTRL_APPS_EN 35
> > +#define IMX8M_RESET_PCIE2_CTRL_APPS_CLK_REQ 36
>
> See above.
>
> > +#define IMX8M_RESET_PCIE2_CTRL_APPS_TURNOFF 37
>
> Move these into imx8m-reset.h
>
> > +
> > +#define IMX7_RESET_NUM 38
>
> And add a separate IMX8M_RESET_NUM.
>
> >
> > #endif
> >
> > diff --git a/include/dt-bindings/reset/imx8m-reset.h b/include/dt-bindings/reset/imx8m-reset.h
> > new file mode 100644
> > index 000000000000..8fa840354723
> > --- /dev/null
> > +++ b/include/dt-bindings/reset/imx8m-reset.h
> > @@ -0,0 +1,47 @@
> > +/* SPDX-License-Identifier: GPL-2.0 */
> > +/*
> > + * Copyright (C) 2018 Zodiac Inflight Innovations
> > + *
> > + * Author: Andrey Smirnov <andrew.smirnov@xxxxxxxxx>
> > + */
> > +
> > +#ifndef DT_BINDING_RESET_IMX8M_H
> > +#define DT_BINDING_RESET_IMX8M_H
> > +
> > +#include "imx7-reset.h"
> > +
> > +#define IMX8M_RESET_A53_CORE_POR_RESET0 IMX7_RESET_A7_CORE_POR_RESET0
> > +#define IMX8M_RESET_A53_CORE_POR_RESET1 IMX7_RESET_A7_CORE_POR_RESET1
> > +
> > +#define IMX8M_RESET_A53_CORE_RESET0 IMX7_RESET_A7_CORE_RESET0
> > +#define IMX8M_RESET_A53_CORE_RESET1 IMX7_RESET_A7_CORE_RESET1
> > +
> > +#define IMX8M_RESET_A53_DBG_RESET0 IMX7_RESET_A7_DBG_RESET0
> > +#define IMX8M_RESET_A53_DBG_RESET1 IMX7_RESET_A7_DBG_RESET1
> > +
> > +#define IMX8M_RESET_A53_ETM_RESET0 IMX7_RESET_A7_ETM_RESET0
> > +#define IMX8M_RESET_A53_ETM_RESET1 IMX7_RESET_A7_ETM_RESET1
> > +
> > +#define IMX8M_RESET_A53_SOC_DBG_RESET IMX7_RESET_A7_SOC_DBG_RESET
> > +#define IMX8M_RESET_A53_L2RESET IMX7_RESET_A7_L2RESET
> > +#define IMX8M_RESET_SW_M4C_RST IMX7_RESET_SW_M4C_RST
> > +#define IMX8M_RESET_SW_M4P_RST IMX7_RESET_SW_M4P_RST
>
> > +#define IMX8M_RESET_EIM_RST IMX7_RESET_EIM_RST
> > +#define IMX8M_RESET_HSICPHY_PORT_RST IMX7_RESET_HSICPHY_PORT_RST
>
> These two don't exist according to the reference manual.
>
> > +#define IMX8M_RESET_USBPHY1_POR IMX7_RESET_USBPHY1_POR
> > +#define IMX8M_RESET_USBPHY1_PORT_RST IMX7_RESET_USBPHY1_PORT_RST
>
> These two don't seem to exist either. I only see a single OTG1_PHY_RESET
> bit in that register.
>
> > +#define IMX8M_RESET_USBPHY2_POR IMX7_RESET_USBPHY2_POR
> > +#define IMX8M_RESET_USBPHY2_PORT_RST IMX7_RESET_USBPHY2_PORT_RST
>
> Same here.
>
> > +#define IMX8M_RESET_MIPI_PHY_MRST IMX7_RESET_MIPI_PHY_MRST
> > +#define IMX8M_RESET_MIPI_PHY_SRST IMX7_RESET_MIPI_PHY_SRST
>
> These don't exist either. The MIPIPHY_RCR register instead has 5
> different _RESET_N bits.
>

OK, I'll incorporate all of the feedback above in v2 as well.

Thanks,
Andrey Smirnov

Next message: Hans Verkuil: "Re: [PATCH v3] media: venus: amend buffer size for bitstream plane"
Previous message: Avri Altman: "RE: [PATCH] scsi: ufs: add fall through annotation"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]