[PATCH v4] arm64: dts: rockchip: Add DT for nanopc-t4
From: Tomeu Vizoso
Date: Tue Nov 27 2018 - 04:12:58 EST
This adds a device tree for the NanoPC-T4 SBC, which is based on the
Rockchip RK3399 SoC and marketed by FriendlyELEC.
Known working:
- Serial
- Ethernet
- HDMI
- USB 2.0
All of the interesting stuff is in a .dtsi because there are at least
two other boards that share most of it: NanoPi M4 and NanoPi NEO4.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@xxxxxxxxxxxxx>
---
v2: - Rename compatible from friendlyelec to friendlyarm, to match
existing bindings
- Remove superfluous node spi1
v3: - Rewrite regulator tree to match the schematics (Heiko)
- Sort top-level nodes alphabetically (Heiko)
- Used defines for GPIO numbers (Heiko)
- Enabled rga (Heiko)
- Removed cdn_dp node (Heiko)
- Removed dependencies to fusb0 as extcon (Heiko)
- Removed superfluous properties (Heiko)
v4: - Replace underscores in node names (Heiko)
- Reorder entry in makefile (Heiko)
- Remove superfluous properties and nodes (Heiko and Shawn)
- Use xin32k as one of the clock outputs of the RK808 (Heiko)
---
.../devicetree/bindings/arm/rockchip.txt | 4 +
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../boot/dts/rockchip/rk3399-nanopc-t4.dts | 18 +
.../boot/dts/rockchip/rk3399-nanopi4.dtsi | 732 ++++++++++++++++++
4 files changed, 755 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-nanopc-t4.dts
create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi
diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt
index 0cc71236d639..e907d309486e 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.txt
+++ b/Documentation/devicetree/bindings/arm/rockchip.txt
@@ -71,6 +71,10 @@ Rockchip platforms device tree bindings
Required root node properties:
- compatible = "firefly,roc-rk3399-pc", "rockchip,rk3399";
+- FriendlyElec NanoPC-T4 board:
+ Required root node properties:
+ - compatible = "friendlyarm,nanopc-t4", "rockchip,rk3399";
+
- ChipSPARK PopMetal-RK3288 board:
Required root node properties:
- compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288";
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 49042c477870..19c129702e06 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -14,6 +14,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-ficus.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-firefly.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-gru-bob.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-gru-kevin.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopc-t4.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-puma-haikou.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rock960.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-nanopc-t4.dts b/arch/arm64/boot/dts/rockchip/rk3399-nanopc-t4.dts
new file mode 100644
index 000000000000..0965712b4464
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-nanopc-t4.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * FriendlyElec NanoPC-T4 board device tree source
+ *
+ * Copyright (c) 2018 FriendlyElec Computer Tech. Co., Ltd.
+ * (http://www.friendlyarm.com)
+ *
+ * Copyright (c) 2018 Collabora Ltd.
+ */
+
+/dts-v1/;
+#include "rk3399-nanopi4.dtsi"
+
+/ {
+ model = "FriendlyElec NanoPC-T4";
+ compatible = "friendlyarm,nanopc-t4", "rockchip,rk3399";
+};
+
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi
new file mode 100644
index 000000000000..e10b98d637d3
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi
@@ -0,0 +1,732 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * RK3399-based FriendlyElec boards device tree source
+ *
+ * Copyright (c) 2016 Fuzhou Rockchip Electronics Co., Ltd
+ *
+ * Copyright (c) 2018 FriendlyElec Computer Tech. Co., Ltd.
+ * (http://www.friendlyarm.com)
+ *
+ * Copyright (c) 2018 Collabora Ltd.
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/linux-event-codes.h>
+#include "rk3399.dtsi"
+#include "rk3399-opp.dtsi"
+
+/ {
+ chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ clkin_gmac: external-gmac-clock {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ clock-output-names = "clkin_gmac";
+ #clock-cells = <0>;
+ };
+
+ vdd_5v: vdd-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_5v";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcc5v0_core: vcc5v0-core {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_core";
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vdd_5v>;
+ };
+
+ vcc3v3_sys: vcc3v3-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc5v0_core>;
+ };
+
+ vcc5v0_sys: vcc5v0-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vdd_5v>;
+ };
+
+ vcc5v0_usb1: vcc5v0-usb1 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_usb1";
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc5v0_usb2: vcc5v0-usb2 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_usb2";
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ /* switched by pmic_sleep */
+ vcc1v8_s3: vcca1v8_s3: vcc1v8-s3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc1v8_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_1v8>;
+ };
+
+ vcc3v0_sd: vcc3v0-sd {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 RK_PA1 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_pwr_h>;
+ regulator-always-on;
+ regulator-max-microvolt = <3000000>;
+ regulator-min-microvolt = <3000000>;
+ regulator-name = "vcc3v0_sd";
+ vin-supply = <&vcc3v3_sys>;
+ };
+
+ vbus_typec: vbus-typec {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>;
+ regulator-name = "vbus_typec";
+ regulator-always-on;
+ vin-supply = <&vdd_5v>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&power_key>;
+
+ button@0 {
+ debounce-interval = <100>;
+ gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
+ label = "GPIO Key Power";
+ linux,code = <KEY_POWER>;
+ linux,input-type = <1>;
+ wakeup-source;
+ };
+ };
+
+ adc-keys {
+ compatible = "adc-keys";
+ io-channels = <&saradc 1>;
+ io-channel-names = "buttons";
+ poll-interval = <100>;
+ keyup-threshold-microvolt = <1800000>;
+
+ button-up {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ press-threshold-microvolt = <100000>;
+ };
+
+ button-down {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ press-threshold-microvolt = <300000>;
+ };
+ };
+
+ leds: gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 =<&leds_gpio>;
+
+ led@1 {
+ gpios = <&gpio0 RK_PB5 GPIO_ACTIVE_HIGH>;
+ label = "status_led";
+ linux,default-trigger = "heartbeat";
+ linux,default-trigger-delay-ms = <0>;
+ };
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rk808 1>;
+ clock-names = "ext_clock";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_enable_h>;
+
+ /*
+ * On the module itself this is one of these (depending
+ * on the actual card populated):
+ * - SDIO_RESET_L_WL_REG_ON
+ * - PDN (power down when low)
+ */
+ reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&cpu_l0 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l1 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l2 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l3 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_b0 {
+ cpu-supply = <&vdd_cpu_b>;
+};
+
+&cpu_b1 {
+ cpu-supply = <&vdd_cpu_b>;
+};
+
+&emmc_phy {
+ status = "okay";
+};
+
+&gmac {
+ phy-supply = <&vcc3v3_s3>;
+ phy-mode = "rgmii";
+ clock_in_out = "input";
+ snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 50000>;
+ assigned-clocks = <&cru SCLK_RMII_SRC>;
+ assigned-clock-parents = <&clkin_gmac>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ tx_delay = <0x28>;
+ rx_delay = <0x11>;
+ status = "okay";
+};
+
+&gpu {
+ status = "okay";
+ mali-supply = <&vdd_gpu>;
+};
+
+&hdmi {
+ ddc-i2c-bus = <&i2c7>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_cec>;
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+ i2c-scl-rising-time-ns = <160>;
+ i2c-scl-falling-time-ns = <30>;
+ clock-frequency = <400000>;
+
+ vdd_cpu_b: regulator@40 {
+ compatible = "silergy,syr827";
+ reg = <0x40>;
+ vin-supply = <&vcc3v3_sys>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vsel1_gpio>;
+ regulator-name = "vdd_cpu_b";
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1500000>;
+ regulator-ramp-delay = <1000>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-state = <3>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu: regulator@41 {
+ compatible = "silergy,syr828";
+ reg = <0x41>;
+ vin-supply = <&vcc3v3_sys>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vsel2_gpio>;
+ regulator-name = "vdd_gpu";
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1500000>;
+ regulator-ramp-delay = <1000>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-state = <3>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ rk808: pmic@1b {
+ compatible = "rockchip,rk808";
+ reg = <0x1b>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>;
+ rockchip,system-power-controller;
+ wakeup-source;
+ #clock-cells = <1>;
+ clock-output-names = "xin32k", "rk808-clkout2";
+
+ vcc1-supply = <&vcc3v3_sys>;
+ vcc2-supply = <&vcc3v3_sys>;
+ vcc3-supply = <&vcc3v3_sys>;
+ vcc4-supply = <&vcc3v3_sys>;
+ vcc6-supply = <&vcc3v3_sys>;
+ vcc7-supply = <&vcc3v3_sys>;
+ vcc8-supply = <&vcc3v3_sys>;
+ vcc9-supply = <&vcc3v3_sys>;
+ vcc10-supply = <&vcc3v3_sys>;
+ vcc11-supply = <&vcc3v3_sys>;
+ vcc12-supply = <&vcc3v3_sys>;
+ vddio-supply = <&vcc_3v0>;
+
+ regulators {
+ vdd_center: DCDC_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+ regulator-name = "vdd_center";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_cpu_l: DCDC_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+ regulator-name = "vdd_cpu_l";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc_ddr";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_1v8: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_1v8";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc1v8_dvp: LDO_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc1v8_dvp";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v0_tp: LDO_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc3v0_tp";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc1v8_pmu: LDO_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc1v8_pmu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vccio_sd: LDO_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-init-microvolt = <3000000>;
+ regulator-name = "vccio_sd";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3000000>;
+ };
+ };
+
+ vcca3v0_codec: LDO_REG5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcca3v0_codec";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v5: LDO_REG6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc_1v5";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1500000>;
+ };
+ };
+
+ vcca1v8_codec: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcca1v8_codec";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_3v0: LDO_REG8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc_3v0";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3000000>;
+ };
+ };
+
+ vcc3v3_s3: SWITCH_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc3v3_s3";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_s0: SWITCH_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc3v3_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ i2c-scl-rising-time-ns = <150>;
+ i2c-scl-falling-time-ns = <30>;
+ clock-frequency = <200000>;
+};
+
+&i2c2 {
+ status = "okay";
+};
+
+&i2c4 {
+ status = "okay";
+ i2c-scl-rising-time-ns = <160>;
+ i2c-scl-falling-time-ns = <30>;
+ clock-frequency = <400000>;
+
+ fusb0: typec-portc@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&fusb0_int>;
+ vbus-supply = <&vbus_typec>;
+ status = "okay";
+ };
+};
+
+&i2c7 {
+ status = "okay";
+};
+
+&io_domains {
+ status = "okay";
+
+ bt656-supply = <&vcc1v8_dvp>;
+ audio-supply = <&vcca1v8_codec>;
+ sdmmc-supply = <&vccio_sd>;
+ gpio1830-supply = <&vcc_3v0>;
+};
+
+&pcie_phy {
+ status = "okay";
+ assigned-clocks = <&cru SCLK_PCIEPHY_REF>;
+ assigned-clock-parents = <&cru SCLK_PCIEPHY_REF100M>;
+ assigned-clock-rates = <100000000>;
+};
+
+&pcie0 {
+ status = "okay";
+ ep-gpios = <&gpio2 RK_PA4 GPIO_ACTIVE_HIGH>;
+ num-lanes = <4>;
+ max-link-speed = <2>;
+};
+
+&pinctrl {
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <RK_GPIO1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ vsel1_gpio: vsel1-gpio {
+ rockchip,pins = <RK_GPIO1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ vsel2_gpio: vsel2-gpio {
+ rockchip,pins = <RK_GPIO1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ sd {
+ sdmmc0_pwr_h: sdmmc0-pwr-h {
+ rockchip,pins =
+ <RK_GPIO0 RK_PA1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ fusb30x {
+ fusb0_int: fusb0-int {
+ rockchip,pins = <RK_GPIO1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ sdio-pwrseq {
+ wifi_enable_h: wifi-enable-h {
+ rockchip,pins = <RK_GPIO0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ rockchip-key {
+ power_key: power-key {
+ rockchip,pins = <RK_GPIO0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ gpio-leds {
+ leds_gpio: leds-gpio {
+ rockchip,pins = <RK_GPIO0 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pmu_io_domains {
+ status = "okay";
+ pmu1830-supply = <&vcc_3v0>;
+};
+
+&pwm0 {
+ status = "okay";
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+&pwm2 {
+ status = "okay";
+ pinctrl-names = "active";
+ pinctrl-0 = <&pwm2_pin_pull_down>;
+};
+
+&saradc {
+ status = "okay";
+ vref-supply = <&vcca1v8_s3>;
+};
+
+&sdhci {
+ bus-width = <8>;
+ mmc-hs400-1_8v;
+ non-removable;
+ mmc-hs400-enhanced-strobe;
+ status = "okay";
+};
+
+&sdio0 {
+ bus-width = <4>;
+ disable-wp;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdio0_bus4 &sdio0_cmd &sdio0_clk>;
+ sd-uhs-sdr104;
+ status = "okay";
+};
+
+&sdmmc {
+ bus-width = <4>;
+ disable-wp;
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ vmmc-supply = <&vcc3v0_sd>;
+ vqmmc-supply = <&vccio_sd>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+ sd-uhs-sdr104;
+ status = "okay";
+};
+
+&tcphy0 {
+ status = "okay";
+};
+
+&tcphy1 {
+ status = "okay";
+};
+
+&tsadc {
+ /* tshut mode 0:CRU 1:GPIO */
+ rockchip,hw-tshut-mode = <1>;
+ /* tshut polarity 0:LOW 1:HIGH */
+ rockchip,hw-tshut-polarity = <1>;
+ status = "okay";
+};
+
+&u2phy0 {
+ status = "okay";
+
+ u2phy0_otg: otg-port {
+ status = "okay";
+ };
+
+ u2phy0_host: host-port {
+ phy-supply = <&vcc5v0_usb1>;
+ status = "okay";
+ };
+};
+
+&u2phy1 {
+ status = "okay";
+
+ u2phy1_otg: otg-port {
+ status = "okay";
+ };
+
+ u2phy1_host: host-port {
+ phy-supply = <&vcc5v0_usb2>;
+ status = "okay";
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer &uart0_cts>;
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart4 {
+ status = "okay";
+};
+
+&usbdrd3_0 {
+ status = "okay";
+};
+
+&usbdrd3_1 {
+ status = "okay";
+};
+
+&usbdrd_dwc3_0 {
+ status = "okay";
+};
+
+&usbdrd_dwc3_1 {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&usb_host1_ehci {
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ status = "okay";
+};
+
+&vopb {
+ status = "okay";
+};
+
+&vopb_mmu {
+ status = "okay";
+};
+
+&vopl {
+ status = "okay";
+};
+
+&vopl_mmu {
+ status = "okay";
+};
--
2.19.1