[PATCH 1/5] usb: mtu3: remove QMU checksum

From: Chunfeng Yun
Date: Wed Nov 28 2018 - 21:35:23 EST


The QMU checksum calculation is redundant, mostly used by debug,
so remove it here.

Signed-off-by: Chunfeng Yun <chunfeng.yun@xxxxxxxxxxxx>
---
drivers/usb/mtu3/mtu3_core.c | 2 --
drivers/usb/mtu3/mtu3_qmu.c | 26 --------------------------
2 files changed, 28 deletions(-)

diff --git a/drivers/usb/mtu3/mtu3_core.c b/drivers/usb/mtu3/mtu3_core.c
index ae70b9bfd797..3dce5fd9887d 100644
--- a/drivers/usb/mtu3/mtu3_core.c
+++ b/drivers/usb/mtu3/mtu3_core.c
@@ -592,8 +592,6 @@ static void mtu3_regs_init(struct mtu3 *mtu)
mtu3_clrbits(mbase, U3D_LINK_RESET_INFO, WTCHRP_MSK);
/* U2/U3 detected by HW */
mtu3_writel(mbase, U3D_DEVICE_CONF, 0);
- /* enable QMU 16B checksum */
- mtu3_setbits(mbase, U3D_QCR0, QMU_CS16B_EN);
/* vbus detected by HW */
mtu3_clrbits(mbase, U3D_MISC_CTRL, VBUS_FRC_EN | VBUS_ON);
}
diff --git a/drivers/usb/mtu3/mtu3_qmu.c b/drivers/usb/mtu3/mtu3_qmu.c
index ff62ba232177..73ac042c45a8 100644
--- a/drivers/usb/mtu3/mtu3_qmu.c
+++ b/drivers/usb/mtu3/mtu3_qmu.c
@@ -154,27 +154,6 @@ void mtu3_gpd_ring_free(struct mtu3_ep *mep)
memset(ring, 0, sizeof(*ring));
}

-/*
- * calculate check sum of a gpd or bd
- * add "noinline" and "mb" to prevent wrong calculation
- */
-static noinline u8 qmu_calc_checksum(u8 *data)
-{
- u8 chksum = 0;
- int i;
-
- data[1] = 0x0; /* set checksum to 0 */
-
- mb(); /* ensure the gpd/bd is really up-to-date */
- for (i = 0; i < QMU_CHECKSUM_LEN; i++)
- chksum += data[i];
-
- /* Default: HWO=1, @flag[bit0] */
- chksum += 1;
-
- return 0xFF - chksum;
-}
-
void mtu3_qmu_resume(struct mtu3_ep *mep)
{
struct mtu3 *mtu = mep->mtu;
@@ -260,7 +239,6 @@ static int mtu3_prepare_tx_gpd(struct mtu3_ep *mep, struct mtu3_request *mreq)
if (req->zero)
gpd->ext_flag |= GPD_EXT_FLAG_ZLP;

- gpd->chksum = qmu_calc_checksum((u8 *)gpd);
gpd->flag |= GPD_FLAGS_HWO;

mreq->gpd = gpd;
@@ -295,7 +273,6 @@ static int mtu3_prepare_rx_gpd(struct mtu3_ep *mep, struct mtu3_request *mreq)
gpd->next_gpd = cpu_to_le32(lower_32_bits(enq_dma));
ext_addr |= GPD_EXT_NGP(upper_32_bits(enq_dma));
gpd->rx_ext_addr = cpu_to_le16(ext_addr);
- gpd->chksum = qmu_calc_checksum((u8 *)gpd);
gpd->flag |= GPD_FLAGS_HWO;

mreq->gpd = gpd;
@@ -323,7 +300,6 @@ int mtu3_qmu_start(struct mtu3_ep *mep)
/* set QMU start address */
write_txq_start_addr(mbase, epnum, ring->dma);
mtu3_setbits(mbase, MU3D_EP_TXCR0(epnum), TX_DMAREQEN);
- mtu3_setbits(mbase, U3D_QCR0, QMU_TX_CS_EN(epnum));
/* send zero length packet according to ZLP flag in GPD */
mtu3_setbits(mbase, U3D_QCR1, QMU_TX_ZLP(epnum));
mtu3_writel(mbase, U3D_TQERRIESR0,
@@ -338,7 +314,6 @@ int mtu3_qmu_start(struct mtu3_ep *mep)
} else {
write_rxq_start_addr(mbase, epnum, ring->dma);
mtu3_setbits(mbase, MU3D_EP_RXCR0(epnum), RX_DMAREQEN);
- mtu3_setbits(mbase, U3D_QCR0, QMU_RX_CS_EN(epnum));
/* don't expect ZLP */
mtu3_clrbits(mbase, U3D_QCR3, QMU_RX_ZLP(epnum));
/* move to next GPD when receive ZLP */
@@ -441,7 +416,6 @@ static void qmu_tx_zlp_error_handler(struct mtu3 *mtu, u8 epnum)

/* by pass the current GDP */
gpd_current->flag |= GPD_FLAGS_BPS;
- gpd_current->chksum = qmu_calc_checksum((u8 *)gpd_current);
gpd_current->flag |= GPD_FLAGS_HWO;

/*enable DMAREQEN, switch back to QMU mode */
--
2.19.1