Re: [PATCH v6 2/2] PCI: amlogic: Add the Amlogic Meson PCIe controller driver

From: Hanjie Lin
Date: Wed Dec 05 2018 - 04:54:53 EST




On 2018/12/4 20:00, Lorenzo Pieralisi wrote:
> On Tue, Dec 04, 2018 at 06:40:55PM +0800, Hanjie Lin wrote:
>>
>>
>> On 2018/12/4 6:57, Bjorn Helgaas wrote:
>>> On Mon, Dec 03, 2018 at 04:41:50PM +0000, Lorenzo Pieralisi wrote:
>>>> On Thu, Nov 22, 2018 at 04:53:54PM +0800, Hanjie Lin wrote:
>>>>
>>>> [...]
>>>>
>>>>> +static int meson_pcie_rd_own_conf(struct pcie_port *pp, int where, int size,
>>>>> + u32 *val)
>>>>> +{
>>>>> + struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
>>>>> +
>>>>> + /*
>>>>> + * there is a bug of MESON AXG pcie controller that software can not
>>>>> + * programe PCI_CLASS_DEVICE register, so we must return a fake right
>>>>> + * value to ensure driver could probe successfully.
>>>>> + */
>>>>> + if (where == PCI_CLASS_REVISION) {
>>>>> + *val = readl(pci->dbi_base + PCI_CLASS_REVISION);
>>>>> + /* keep revision id */
>>>>> + *val &= PCI_CLASS_REVISION_MASK;
>>>>> + *val |= PCI_CLASS_BRIDGE_PCI << 16;
>>>>> + return PCIBIOS_SUCCESSFUL;
>>>>> + }
>>>>
>>>> As I said before, this looks broken. If this code (or other drivers with
>>>> the same broken assumptions, eg dwc/pcie-qcom.c) carries out a, say,
>>>> byte sized config access of eg PCI_CLASS_DEVICE you will get junk out of
>>>> it according to your comment above.
>>>>
>>>> I would like to pick Bjorn's brain on this to see what we can really do
>>>> to fix this (and other) drivers.
>>>
>>> - Check to see whether you're reading anything in the 32-bit dword at
>>> offset 0x08.
>>>
>>> - Do the 32-bit readl().
>>>
>>> - Insert the correct Sub-Class and Base Class code (you also throw
>>> away the Programming Interface; not sure why that is)
>>>
>>> - If you're reading something smaller than 32 bits, mask & shift as
>>> needed. pci_bridge_emul_conf_read() does something similar that
>>> you might be able to copy.
>>>
>>> Out of curiosity, what code depends on PCI_CLASS_BRIDGE_PCI? There
>>> are several places in the kernel that currently depend on it, but I
>>> think several of them *should* be checking dev->hdr_type to identify a
>>> type 1 header instead.
>>>
>>> Bjorn
>>>
>>> .
>>>
>>
>> Yes, it would be broken in particular scenes(eg: read 1 or 2 bytes from 0xa/PCI_CLASS_DEVICE)
>> that I didn't considered.
>>
>> As your suggestion, I consider some code below may help this issue:
>> 1, First call dw_pcie_read() help to read 1/2/4 bytes from register,
>> request all other *size* bytes will return error and dw_pcie_read()
>> will also check register alignment.
>>
>> 2, If dw_pcie_read() return success and *where* is 0x8/PCI_CLASS_DEVICE or 0xa/PCI_CLASS_REVISION,
>> we may need to correct class code.
>> As PCI_CLASS_REVISION is two-bytes register, so only when read 4 bytes from 0x8/PCI_CLASS_DEVICE
>> or read 2 bytes from 0xa/PCI_CLASS_REVISION we should correct the class code.
>>
>> ps: read 1 byte from 0xa/PCI_CLASS_REVISION or 0xb will get incorrect value.
>
> You can fix this too.
>
>> static int meson_pcie_rd_own_conf(struct pcie_port *pp, int where, int size,
>> u32 *val)
>> {
>> struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
>> int ret;
>>
>> ret = dw_pcie_read(pci->dbi_base + where, size, val);
>> if (ret != PCIBIOS_SUCCESSFUL)
>> return ret;
>>
>> /*
>> * there is a bug of MESON AXG pcie controller that software can not
>> * programe PCI_CLASS_DEVICE register, so we must return a fake right
>
> "There is a bug in the MESON AXG pcie controller whereby software cannot
> programme the PCI_CLASS_DEVICE register, so we must fabricate the return
> value in the config accessors."
>

Ok, it's more clear :)

>> * value to ensure driver could probe successfully.
>> */
>> if (where == PCI_CLASS_REVISION && size == 4)
>> *val = (PCI_CLASS_BRIDGE_PCI << 16) | (*val & 0xffff);
>> else if (where == PCI_CLASS_DEVICE && size == 2)
>> *val = PCI_CLASS_BRIDGE_PCI;
>
> You can further filter it with (where & 0x1) == PCI_CLASS_DEVICE
> and handle the size accordingly, so that even a byte access would
> work, for completeness.
>
> Lorenzo
>

Of course, I will add process to handle one-byte access from 0xa/0xb register
in next-version.

thanks.

hanjie

>> return PCIBIOS_SUCCESSFUL;
>> }
>>
>> 3, We must ensure class is PCI_CLASS_BRIDGE_PCI except right hdr_type,
>> or pci_setup_device() will get failed:
>>
>> ...
>> class = pci_class(dev);
>> dev->revision = class & 0xff;
>> dev->class = class >> 8; /* upper 3 bytes */
>> ....
>> switch (dev->hdr_type) { /* header type */
>> ...
>> case PCI_HEADER_TYPE_BRIDGE: /* bridge header */
>> if (class != PCI_CLASS_BRIDGE_PCI) /* class must be PCI_CLASS_BRIDGE_PCI */
>> goto bad;
>>
>>
>> thanks.
>>
>> hanjie
>
> .
>