[PATCH V2 2/4] ARM: dts: imx6qdl-sabresd: add light sensor support

From: Anson Huang
Date: Wed Dec 05 2018 - 20:42:42 EST


Add isl29023 light sensor support on i2c3 bus, the light
sensor's power is controlled by a fixed regulator, since
the isl29023 driver and most of other sensors on same
board like mag3110 and mma8451 do NOT support regulator
operation currently, they are all controlled by this
regulator, so this patch also adds the fixed regulator
support and make it always on.

Signed-off-by: Anson Huang <Anson.Huang@xxxxxxx>
---
arch/arm/boot/dts/imx6qdl-sabresd.dtsi | 33 +++++++++++++++++++++++++++++++++
1 file changed, 33 insertions(+)

diff --git a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
index 66972e8..d07c250 100644
--- a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
@@ -54,6 +54,18 @@
enable-active-high;
};

+ reg_sensors: regulator-sensors {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sensors_reg>;
+ regulator-name = "sensors-supply";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
gpio-keys {
compatible = "gpio-keys";
pinctrl-names = "default";
@@ -410,6 +422,15 @@
interrupts = <7 2>;
wakeup-gpios = <&gpio6 7 0>;
};
+
+ light-sensor@44 {
+ compatible = "isil,isl29023";
+ reg = <0x44>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3_isl29023_int>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+ };
};

&iomuxc {
@@ -511,6 +532,12 @@
>;
};

+ pinctrl_i2c3_isl29023_int: i2c3isl29023intgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_DA9__GPIO3_IO09 0xb0b1
+ >;
+ };
+
pinctrl_ipu1_csi0: ipu1csi0grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
@@ -559,6 +586,12 @@
>;
};

+ pinctrl_sensors_reg: sensorsreggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_EB3__GPIO2_IO31 0x1b0b0
+ >;
+ };
+
pinctrl_uart1: uart1grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
--
2.7.4