Re: [PATCH v3 2/2] dt-bindings: iio: adc: Add docs for AD7606 ADC
From: Rob Herring
Date: Fri Dec 07 2018 - 18:47:46 EST
On Thu, Nov 29, 2018 at 06:57:43PM +0200, Stefan Popa wrote:
> Document support for AD7606 Analog to Digital Converter.
>
> Signed-off-by: Stefan Popa <stefan.popa@xxxxxxxxxx>
> ---
> Changes in v2:
> - fixed indentation issues.
> - used gpios instead of gpio.
> - added vendor prefix for conversion-start-gpios, first-data-gpios,
> and range-gpios.
> Changes in v3:
> - Added adi,oversampling-ratio-gpios.
>
> .../devicetree/bindings/iio/adc/adi,ad7606.txt | 54 ++++++++++++++++++++++
> MAINTAINERS | 1 +
> 2 files changed, 55 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
>
> diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
> new file mode 100644
> index 0000000..02fae23
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
> @@ -0,0 +1,54 @@
> +Analog Devices AD7606 Simultaneous Sampling ADC
> +
> +Required properties for the AD7606:
> +
> +- compatible: Must be one of
> + * "adi,ad7605-4"
> + * "adi,ad7606-8"
> + * "adi,ad7606-6"
> + * "adi,ad7606-4"
> +- reg: SPI chip select number for the device
> +- spi-max-frequency: Max SPI frequency to use
> + see: Documentation/devicetree/bindings/spi/spi-bus.txt
> +- spi-cpha: See Documentation/devicetree/bindings/spi/spi-bus.txt
> +- avcc-supply: phandle to the Avcc power supply
> +- interrupts: IRQ line for the ADC
> + see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
> +- adi,conversion-start-gpios: must be the device tree identifier of the CONVST pin.
> + This logic input is used to initiate conversions on the analog
> + input channels.
Needs to say active high or low and set the flag appropriately.
> +
> +Optional properties:
> +
> +- reset-gpios: must be the device tree identifier of the RESET pin. If specified,
> + it will be asserted during driver probe.
active high or low?
> +- standby-gpios: must be the device tree identifier of the STBY pin. This pin is used
> + to place the AD7606 into one of two power-down modes, Standby mode or
> + Shutdown mode.
active high or low?
> +- adi,first-data-gpios: must be the device tree identifier of the FRSTDATA pin.
> + The FRSTDATA output indicates when the first channel, V1, is
> + being read back on either the parallel, byte or serial interface.
active high or low?
> +- adi,range-gpios: must be the device tree identifier of the RANGE pin. The polarity on
> + this pin determines the input range of the analog input channels. If
> + this pin is tied to a logic high, the analog input range is ±10V for
> + all channels. If this pin is tied to a logic low, the analog input range
> + is ±5V for all channels.
> +
> +Example:
> +
> + adc@0 {
> + compatible = "adi,ad7606-8";
> + reg = <0>;
> + spi-max-frequency = <1000000>;
> + spi-cpol;
> +
> + avcc-supply = <&adc_vref>;
> +
> + interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-parent = <&gpio>;
> +
> + adi,conversion-start-gpios = <&gpio 17 0>;
> + reset-gpios = <&gpio 27 0>;
> + adi,first-data-gpios = <&gpio 22 0>;
> + standby-gpios = <&gpio 24 0>;
> + };
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 843545d..6d63db4 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -845,6 +845,7 @@ L: linux-iio@xxxxxxxxxxxxxxx
> W: http://ez.analog.com/community/linux-device-drivers
> S: Supported
> F: drivers/iio/adc/ad7606.c
> +F: Documentation/devicetree/bindings/iio/adc/ad7606.txt
>
> ANALOG DEVICES INC AD9389B DRIVER
> M: Hans Verkuil <hans.verkuil@xxxxxxxxx>
> --
> 2.7.4
>