[PATCH 3/5] spi: stm32: add driver for STM32F4 controller
From: cezary . gapinski
Date: Sun Dec 09 2018 - 08:54:41 EST
From: Cezary Gapinski <cezary.gapinski@xxxxxxxxx>
The STM32F4 Serial Peripheral Interface (SPI) can be used to communicate
with external devices while using the specific synchronous protocol. This
version supports full-duplex communication with 8 or 16-bit per word.
DMA capability is optionally supported when RX and TX DMA channels are
enabled at the same time for transfer longer than 16 bytes.
Now only master mode can be used.
Signed-off-by: Cezary Gapinski <cezary.gapinski@xxxxxxxxx>
---
drivers/spi/Kconfig | 10 +
drivers/spi/Makefile | 1 +
drivers/spi/spi-stm32f4.c | 1002 +++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 1013 insertions(+)
create mode 100644 drivers/spi/spi-stm32f4.c
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 0151334..fc40616 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -655,6 +655,16 @@ config SPI_STM32H7
is not available, the driver automatically falls back to
PIO mode.
+config SPI_STM32F4
+ tristate "STMicroelectronics STM32F4 SPI controller"
+ depends on ARCH_STM32 || COMPILE_TEST
+ help
+ SPI driver for STMicroelectronics STM32F4 SoCs.
+
+ STM32F4 SPI controller supports DMA and PIO modes. When DMA
+ is not available, the driver automatically falls back to
+ PIO mode.
+
config SPI_STM32_QSPI
tristate "STMicroelectronics STM32 QUAD SPI controller"
depends on ARCH_STM32 || COMPILE_TEST
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 6f24938..3fb0f98 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -94,6 +94,7 @@ obj-$(CONFIG_SPI_SIRF) += spi-sirf.o
obj-$(CONFIG_SPI_SLAVE_MT27XX) += spi-slave-mt27xx.o
obj-$(CONFIG_SPI_SPRD) += spi-sprd.o
obj-$(CONFIG_SPI_SPRD_ADI) += spi-sprd-adi.o
+obj-$(CONFIG_SPI_STM32F4) += spi-stm32f4.o
obj-$(CONFIG_SPI_STM32H7) += spi-stm32h7.o
obj-$(CONFIG_SPI_STM32_QSPI) += spi-stm32-qspi.o
obj-$(CONFIG_SPI_ST_SSC4) += spi-st-ssc4.o
diff --git a/drivers/spi/spi-stm32f4.c b/drivers/spi/spi-stm32f4.c
new file mode 100644
index 0000000..755222b
--- /dev/null
+++ b/drivers/spi/spi-stm32f4.c
@@ -0,0 +1,1002 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// STMicroelectronics STM32F4 SPI Controller driver (master mode only)
+//
+// Author(s): Cezary Gapinski <cezary.gapinski@xxxxxxxxx>
+//
+// This driver is based on spi-stm32h7.c
+
+#include <linux/debugfs.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/dmaengine.h>
+#include <linux/gpio.h>
+#include <linux/interrupt.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/pm_runtime.h>
+#include <linux/reset.h>
+#include <linux/spi/spi.h>
+
+#define DRIVER_NAME "spi_stm32f4"
+
+/* STM32F4 SPI registers */
+#define STM32F4_SPI_CR1 0x00
+#define STM32F4_SPI_CR2 0x04
+#define STM32F4_SPI_SR 0x08
+#define STM32F4_SPI_DR 0x0C
+#define STM32F4_SPI_I2SCFGR 0x1C
+
+/* STM32F4_SPI_CR1 bit fields */
+#define STM32F4_SPI_CR1_CPHA BIT(0)
+#define STM32F4_SPI_CR1_CPOL BIT(1)
+#define STM32F4_SPI_CR1_MSTR BIT(2)
+#define STM32F4_SPI_CR1_BR_SHIFT 3
+#define STM32F4_SPI_CR1_BR GENMASK(5, 3)
+#define STM32F4_SPI_CR1_SPE BIT(6)
+#define STM32F4_SPI_CR1_LSBFRST BIT(7)
+#define STM32F4_SPI_CR1_SSI BIT(8)
+#define STM32F4_SPI_CR1_SSM BIT(9)
+#define STM32F4_SPI_CR1_RXONLY BIT(10)
+#define STM32F4_SPI_CR1_DFF BIT(11)
+#define STM32F4_SPI_CR1_CRCNEXT BIT(12)
+#define STM32F4_SPI_CR1_CRCEN BIT(13)
+#define STM32F4_SPI_CR1_BIDIOE BIT(14)
+#define STM32F4_SPI_CR1_BIDIMODE BIT(15)
+#define STM32F4_SPI_CR1_BR_MIN 0
+#define STM32F4_SPI_CR1_BR_MAX (GENMASK(5, 3) >> 3)
+
+/* STM32F4_SPI_CR2 bit fields */
+#define STM32F4_SPI_CR2_RXDMAEN BIT(0)
+#define STM32F4_SPI_CR2_TXDMAEN BIT(1)
+#define STM32F4_SPI_CR2_SSOE BIT(2)
+#define STM32F4_SPI_CR2_FRF BIT(4)
+#define STM32F4_SPI_CR2_ERRIE BIT(5)
+#define STM32F4_SPI_CR2_RXNEIE BIT(6)
+#define STM32F4_SPI_CR2_TXEIE BIT(7)
+
+/* STM32F4_SPI_SR bit fields */
+#define STM32F4_SPI_SR_RXNE BIT(0)
+#define STM32F4_SPI_SR_TXE BIT(1)
+#define STM32F4_SPI_SR_CHSIDE BIT(2)
+#define STM32F4_SPI_SR_UDR BIT(3)
+#define STM32F4_SPI_SR_CRCERR BIT(4)
+#define STM32F4_SPI_SR_MODF BIT(5)
+#define STM32F4_SPI_SR_OVR BIT(6)
+#define STM32F4_SPI_SR_BSY BIT(7)
+#define STM32F4_SPI_SR_FRE BIT(8)
+
+/* STM32F4_SPI_I2SCFGR bit fields */
+#define STM32F4_SPI_I2SCFGR_I2SMOD BIT(11)
+
+/* STM32F4 SPI Baud Rate min/max divisor */
+#define STM32F4_SPI_BR_DIV_MIN (2 << STM32F4_SPI_CR1_BR_MIN)
+#define STM32F4_SPI_BR_DIV_MAX (2 << STM32F4_SPI_CR1_BR_MAX)
+
+/* use PIO for small transfers, avoiding DMA setup/teardown overhead */
+#define STM32F4_DMA_MIN_BYTES 16
+
+/**
+ * struct stm32f4_spi - private data of the SPI controller
+ * @dev: driver model representation of the controller
+ * @master: controller master interface
+ * @base: virtual memory area
+ * @clk: hw kernel clock feeding the SPI clock generator
+ * @clk_rate: rate of the hw kernel clock feeding the SPI clock generator
+ * @rst: SPI controller reset line
+ * @lock: prevent I/O concurrent access
+ * @irq: SPI controller interrupt line
+ * @cur_speed: speed configured in Hz
+ * @cur_bpw: number of bits in a single SPI data frame
+ * @cur_xferlen: current transfer length in bytes
+ * @cur_usedma: boolean to know if dma is used in current transfer
+ * @tx_buf: data to be written, or NULL
+ * @rx_buf: data to be read, or NULL
+ * @tx_len: number of data to be written in bytes
+ * @rx_len: number of data to be read in bytes
+ * @phys_addr: SPI registers physical base address
+ */
+struct stm32f4_spi {
+ struct device *dev;
+ struct spi_master *master;
+ void __iomem *base;
+ struct clk *clk;
+ u32 clk_rate;
+ struct reset_control *rst;
+ spinlock_t lock;
+ int irq;
+
+ unsigned int cur_speed;
+ unsigned int cur_bpw;
+ unsigned int cur_xferlen;
+ bool cur_usedma;
+
+ const void *tx_buf;
+ void *rx_buf;
+ int tx_len;
+ int rx_len;
+ dma_addr_t phys_addr;
+};
+
+static inline void stm32f4_spi_set_bits(struct stm32f4_spi *spi,
+ u32 offset, u32 bits)
+{
+ writel_relaxed(readl_relaxed(spi->base + offset) | bits,
+ spi->base + offset);
+}
+
+static inline void stm32f4_spi_clr_bits(struct stm32f4_spi *spi,
+ u32 offset, u32 bits)
+{
+ writel_relaxed(readl_relaxed(spi->base + offset) & ~bits,
+ spi->base + offset);
+}
+
+/**
+ * stm32f4_spi_prepare_mbr - Determine STM32F4_SPI_CR1.BR value
+ * @spi: pointer to the spi controller data structure
+ * @speed_hz: requested speed
+ *
+ * Return STM32F4_SPI_CR1.BR value in case of success or -EINVAL
+ */
+static int stm32f4_spi_prepare_mbr(struct stm32f4_spi *spi, u32 speed_hz)
+{
+ u32 div, mbrdiv;
+
+ div = DIV_ROUND_UP(spi->clk_rate, speed_hz);
+
+ /*
+ * SPI framework set xfer->speed_hz to master->max_speed_hz if
+ * xfer->speed_hz is greater than master->max_speed_hz, and it returns
+ * an error when xfer->speed_hz is lower than master->min_speed_hz, so
+ * no need to check it there.
+ * However, we need to ensure the following calculations.
+ */
+ if (div < STM32F4_SPI_BR_DIV_MIN ||
+ div > STM32F4_SPI_BR_DIV_MAX)
+ return -EINVAL;
+
+ /* Determine the first power of 2 greater than or equal to div */
+ if (div & (div - 1))
+ mbrdiv = fls(div);
+ else
+ mbrdiv = fls(div) - 1;
+
+ spi->cur_speed = spi->clk_rate / (1 << mbrdiv);
+
+ return mbrdiv - 1;
+}
+
+/**
+ * stm32f4_spi_write_tx - Write bytes to Data Register
+ * @spi: pointer to the spi controller data structure
+ *
+ * Read from tx_buf depends on remaining bytes to avoid to read beyond
+ * tx_buf end.
+ */
+static void stm32f4_spi_write_tx(struct stm32f4_spi *spi)
+{
+ if (spi->tx_len > 0) {
+ u32 offs = spi->cur_xferlen - spi->tx_len;
+
+ if (spi->cur_bpw == 16) {
+ const u16 *tx_buf16 = (const u16 *)(spi->tx_buf + offs);
+
+ writew_relaxed(*tx_buf16, spi->base + STM32F4_SPI_DR);
+ spi->tx_len -= sizeof(u16);
+ } else {
+ const u8 *tx_buf8 = (const u8 *)(spi->tx_buf + offs);
+
+ writeb_relaxed(*tx_buf8, spi->base + STM32F4_SPI_DR);
+ spi->tx_len -= sizeof(u8);
+ }
+ }
+
+ dev_dbg(spi->dev, "%s: %d bytes left\n", __func__, spi->tx_len);
+}
+
+/**
+ * stm32f4_spi_read_rx - Read bytes from Data Register
+ * @spi: pointer to the spi controller data structure
+ *
+ * Write in rx_buf depends on remaining bytes to avoid to write beyond
+ * rx_buf end.
+ */
+static void stm32f4_spi_read_rx(struct stm32f4_spi *spi)
+{
+ if (spi->rx_len > 0) {
+ u32 offs = spi->cur_xferlen - spi->rx_len;
+
+ if (spi->cur_bpw == 16) {
+ u16 *rx_buf16 = (u16 *)(spi->rx_buf + offs);
+
+ *rx_buf16 = readw_relaxed(spi->base + STM32F4_SPI_DR);
+ spi->rx_len -= sizeof(u16);
+ } else {
+ u8 *rx_buf8 = (u8 *)(spi->rx_buf + offs);
+
+ *rx_buf8 = readb_relaxed(spi->base + STM32F4_SPI_DR);
+ spi->rx_len -= sizeof(u8);
+ }
+ }
+
+ dev_dbg(spi->dev, "%s: %d bytes left\n", __func__, spi->rx_len);
+}
+
+/**
+ * stm32f4_spi_enable - Enable SPI controller
+ * @spi: pointer to the spi controller data structure
+ */
+static void stm32f4_spi_enable(struct stm32f4_spi *spi)
+{
+ dev_dbg(spi->dev, "enable controller\n");
+
+ stm32f4_spi_set_bits(spi, STM32F4_SPI_CR1, STM32F4_SPI_CR1_SPE);
+}
+
+/**
+ * stm32f4_spi_disable - Disable SPI controller
+ * @spi: pointer to the spi controller data structure
+ */
+static void stm32f4_spi_disable(struct stm32f4_spi *spi)
+{
+ unsigned long flags;
+ struct spi_master *master = spi->master;
+
+ dev_dbg(spi->dev, "disable controller\n");
+
+ spin_lock_irqsave(&spi->lock, flags);
+
+ stm32f4_spi_clr_bits(spi, STM32F4_SPI_CR1, STM32F4_SPI_CR1_SPE);
+
+ if (spi->cur_usedma) {
+ dmaengine_terminate_all(master->dma_tx);
+ dmaengine_terminate_all(master->dma_rx);
+ }
+
+ stm32f4_spi_clr_bits(spi, STM32F4_SPI_CR2, STM32F4_SPI_CR2_TXDMAEN |
+ STM32F4_SPI_CR2_RXDMAEN);
+
+ /* Disable interrupts */
+ stm32f4_spi_clr_bits(spi, STM32F4_SPI_CR2, STM32F4_SPI_CR2_RXNEIE |
+ STM32F4_SPI_CR2_ERRIE);
+ /* Sequence to clear OVR flag */
+ readl_relaxed(spi->base + STM32F4_SPI_DR);
+ readl_relaxed(spi->base + STM32F4_SPI_SR);
+
+ spin_unlock_irqrestore(&spi->lock, flags);
+}
+
+/**
+ * stm32f4_spi_can_dma - Determine if the transfer is eligible for DMA use
+ *
+ * If the current transfer size is greater than defined size, use DMA.
+ */
+static bool stm32f4_spi_can_dma(struct spi_master *master,
+ struct spi_device *spi_dev,
+ struct spi_transfer *transfer)
+{
+ struct stm32f4_spi *spi = spi_master_get_devdata(master);
+
+ dev_dbg(spi->dev, "%s: %s\n", __func__,
+ (transfer->len > STM32F4_DMA_MIN_BYTES) ? "true" : "false");
+
+ return (transfer->len > STM32F4_DMA_MIN_BYTES);
+}
+
+/**
+ * stm32f4_spi_irq_event - Interrupt handler for SPI controller events
+ * @irq: interrupt line
+ * @dev_id: SPI controller master interface
+ */
+static irqreturn_t stm32f4_spi_irq_event(int irq, void *dev_id)
+{
+ struct spi_master *master = dev_id;
+ struct stm32f4_spi *spi = spi_master_get_devdata(master);
+ u32 sr, mask;
+ unsigned long flags;
+ bool end = false;
+
+ spin_lock_irqsave(&spi->lock, flags);
+
+ sr = readl_relaxed(spi->base + STM32F4_SPI_SR);
+ /*
+ * BSY flag is not handled in interrupt
+ * TXE flag is set and is handled when RXNE flag occurs
+ */
+ sr &= ~(STM32F4_SPI_SR_BSY | STM32F4_SPI_SR_TXE);
+
+ mask = STM32F4_SPI_SR_RXNE;
+ if (spi->cur_usedma)
+ mask |= STM32F4_SPI_SR_OVR;
+
+ if (!(sr & mask)) {
+ dev_dbg(spi->dev, "spurious IT (sr=0x%08x)\n", sr);
+ spin_unlock_irqrestore(&spi->lock, flags);
+ return IRQ_NONE;
+ }
+
+ if (sr & STM32F4_SPI_SR_OVR) {
+ dev_warn(spi->dev, "Overrun: received value discarded\n");
+
+ /* Sequence to clear OVR flag */
+ readl_relaxed(spi->base + STM32F4_SPI_DR);
+ readl_relaxed(spi->base + STM32F4_SPI_SR);
+
+ /*
+ * If overrun is detected, it means that something went wrong,
+ * so stop the current transfer. For interrupt transfer for
+ * current configuration it should newer occurs. If it is
+ * detected for DMA stop transfer.
+ */
+ end = true;
+ goto end_irq;
+ }
+
+ stm32f4_spi_read_rx(spi);
+ if (spi->rx_len == 0)
+ end = true;
+ else
+ stm32f4_spi_write_tx(spi);
+
+end_irq:
+ spin_unlock_irqrestore(&spi->lock, flags);
+
+ if (end)
+ return IRQ_WAKE_THREAD;
+
+ return IRQ_HANDLED;
+}
+
+/**
+ * stm32f4_spi_irq_thread - Thread of interrupt handler for SPI controller
+ * @irq: interrupt line
+ * @dev_id: SPI controller master interface
+ */
+static irqreturn_t stm32f4_spi_irq_thread(int irq, void *dev_id)
+{
+ struct spi_master *master = dev_id;
+ struct stm32f4_spi *spi = spi_master_get_devdata(master);
+
+ spi_finalize_current_transfer(master);
+ stm32f4_spi_disable(spi);
+
+ return IRQ_HANDLED;
+}
+
+/**
+ * stm32f4_spi_setup - setup device chip select
+ */
+static int stm32f4_spi_setup(struct spi_device *spi_dev)
+{
+ int ret = 0;
+
+ if (!gpio_is_valid(spi_dev->cs_gpio)) {
+ dev_err(&spi_dev->dev, "%d is not a valid gpio\n",
+ spi_dev->cs_gpio);
+ return -EINVAL;
+ }
+
+ dev_dbg(&spi_dev->dev, "%s: set gpio%d output %s\n", __func__,
+ spi_dev->cs_gpio,
+ (spi_dev->mode & SPI_CS_HIGH) ? "low" : "high");
+
+ ret = gpio_direction_output(spi_dev->cs_gpio,
+ !(spi_dev->mode & SPI_CS_HIGH));
+
+ return ret;
+}
+
+/**
+ * stm32f4_spi_prepare_msg - set up the controller to transfer a single message
+ */
+static int stm32f4_spi_prepare_msg(struct spi_master *master,
+ struct spi_message *msg)
+{
+ struct stm32f4_spi *spi = spi_master_get_devdata(master);
+ struct spi_device *spi_dev = msg->spi;
+ unsigned long flags;
+ u32 cr1_clrb = 0, cr1_setb = 0;
+
+ if (spi_dev->mode & SPI_CPOL)
+ cr1_setb |= STM32F4_SPI_CR1_CPOL;
+ else
+ cr1_clrb |= STM32F4_SPI_CR1_CPOL;
+
+ if (spi_dev->mode & SPI_CPHA)
+ cr1_setb |= STM32F4_SPI_CR1_CPHA;
+ else
+ cr1_clrb |= STM32F4_SPI_CR1_CPHA;
+
+ if (spi_dev->mode & SPI_LSB_FIRST)
+ cr1_setb |= STM32F4_SPI_CR1_LSBFRST;
+ else
+ cr1_clrb |= STM32F4_SPI_CR1_LSBFRST;
+
+ dev_dbg(spi->dev, "cpol=%d cpha=%d lsb_first=%d cs_high=%d\n",
+ spi_dev->mode & SPI_CPOL,
+ spi_dev->mode & SPI_CPHA,
+ spi_dev->mode & SPI_LSB_FIRST,
+ spi_dev->mode & SPI_CS_HIGH);
+
+ spin_lock_irqsave(&spi->lock, flags);
+
+ if (cr1_clrb || cr1_setb)
+ writel_relaxed((readl_relaxed(spi->base + STM32F4_SPI_CR1) &
+ ~cr1_clrb) | cr1_setb,
+ spi->base + STM32F4_SPI_CR1);
+
+ spin_unlock_irqrestore(&spi->lock, flags);
+
+ return 0;
+}
+
+/**
+ * stm32f4_spi_dma_rx_cb - DMA callback
+ *
+ * DMA callback is called when the transfer is complete for receiving mode.
+ */
+static void stm32f4_spi_dma_rx_cb(void *data)
+{
+ struct spi_master *master = data;
+ struct stm32f4_spi *spi = spi_master_get_devdata(master);
+
+ spi_finalize_current_transfer(master);
+ stm32f4_spi_disable(spi);
+}
+
+/**
+ * stm32f4_spi_dma_config - configure DMA slave channel depending on current
+ * transfer bits_per_word.
+ */
+static void stm32f4_spi_dma_config(struct stm32f4_spi *spi,
+ struct dma_slave_config *dma_conf,
+ enum dma_transfer_direction dir)
+{
+ enum dma_slave_buswidth buswidth;
+
+ if (spi->cur_bpw == 16)
+ buswidth = DMA_SLAVE_BUSWIDTH_2_BYTES;
+ else
+ buswidth = DMA_SLAVE_BUSWIDTH_1_BYTE;
+
+ memset(dma_conf, 0, sizeof(struct dma_slave_config));
+ dma_conf->direction = dir;
+ if (dma_conf->direction == DMA_DEV_TO_MEM) { /* RX */
+ dma_conf->src_addr = spi->phys_addr + STM32F4_SPI_DR;
+ dma_conf->src_addr_width = buswidth;
+
+ dev_dbg(spi->dev, "Rx DMA config buswidth=%d\n", buswidth);
+ } else if (dma_conf->direction == DMA_MEM_TO_DEV) { /* TX */
+ dma_conf->dst_addr = spi->phys_addr + STM32F4_SPI_DR;
+ dma_conf->dst_addr_width = buswidth;
+
+ dev_dbg(spi->dev, "Tx DMA config buswidth=%d\n", buswidth);
+ }
+}
+
+/**
+ * stm32f4_spi_transfer_one_irq - transfer a single spi_transfer using
+ * interrupts
+ *
+ * It must returns 0 if the transfer is finished or 1 if the transfer is still
+ * in progress.
+ */
+static int stm32f4_spi_transfer_one_irq(struct stm32f4_spi *spi)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&spi->lock, flags);
+
+ stm32f4_spi_set_bits(spi, STM32F4_SPI_CR2, STM32F4_SPI_CR2_RXNEIE |
+ STM32F4_SPI_CR2_ERRIE);
+ stm32f4_spi_enable(spi);
+ stm32f4_spi_write_tx(spi);
+
+ spin_unlock_irqrestore(&spi->lock, flags);
+
+ return 1;
+}
+
+/**
+ * stm32f4_spi_transfer_one_dma - transfer a single spi_transfer using DMA
+ *
+ * It must returns 0 if the transfer is finished or 1 if the transfer is still
+ * in progress.
+ */
+static int stm32f4_spi_transfer_one_dma(struct stm32f4_spi *spi,
+ struct spi_transfer *xfer)
+{
+ struct dma_slave_config tx_dma_conf, rx_dma_conf;
+ struct dma_async_tx_descriptor *tx_dma_desc, *rx_dma_desc;
+ unsigned long flags;
+ struct spi_master *master = spi->master;
+
+ spin_lock_irqsave(&spi->lock, flags);
+
+ rx_dma_desc = NULL;
+ stm32f4_spi_dma_config(spi, &rx_dma_conf, DMA_DEV_TO_MEM);
+ dmaengine_slave_config(master->dma_rx, &rx_dma_conf);
+
+ /* Enable Rx DMA request */
+ stm32f4_spi_set_bits(spi, STM32F4_SPI_CR2, STM32F4_SPI_CR2_RXDMAEN);
+
+ rx_dma_desc = dmaengine_prep_slave_sg(
+ master->dma_rx, xfer->rx_sg.sgl,
+ xfer->rx_sg.nents,
+ rx_dma_conf.direction,
+ DMA_PREP_INTERRUPT);
+
+ tx_dma_desc = NULL;
+ stm32f4_spi_dma_config(spi, &tx_dma_conf, DMA_MEM_TO_DEV);
+ dmaengine_slave_config(master->dma_tx, &tx_dma_conf);
+
+ tx_dma_desc = dmaengine_prep_slave_sg(
+ master->dma_tx, xfer->tx_sg.sgl,
+ xfer->tx_sg.nents,
+ tx_dma_conf.direction,
+ DMA_PREP_INTERRUPT);
+
+ if (!tx_dma_desc || !rx_dma_desc)
+ goto dma_desc_error;
+
+ rx_dma_desc->callback = stm32f4_spi_dma_rx_cb;
+ rx_dma_desc->callback_param = spi->master;
+
+ if (dma_submit_error(dmaengine_submit(rx_dma_desc))) {
+ dev_err(spi->dev, "Rx DMA submit failed\n");
+ goto dma_desc_error;
+ }
+ /* Enable Rx DMA channel */
+ dma_async_issue_pending(master->dma_rx);
+
+ if (dma_submit_error(dmaengine_submit(tx_dma_desc))) {
+ dev_err(spi->dev, "Tx DMA submit failed\n");
+ goto dma_submit_error;
+ }
+ /* Enable Tx DMA channel */
+ dma_async_issue_pending(master->dma_tx);
+
+ /* Enable Tx DMA request */
+ stm32f4_spi_set_bits(spi, STM32F4_SPI_CR2, STM32F4_SPI_CR2_TXDMAEN);
+
+ /*
+ * End of transfer will be handled in DMA RX Callback.
+ * Enable the interrupts to detect OVR flag
+ */
+ stm32f4_spi_set_bits(spi, STM32F4_SPI_CR2, STM32F4_SPI_CR2_ERRIE);
+
+ stm32f4_spi_enable(spi);
+
+ spin_unlock_irqrestore(&spi->lock, flags);
+
+ return 1;
+
+dma_submit_error:
+ dmaengine_terminate_all(master->dma_rx);
+
+dma_desc_error:
+ stm32f4_spi_clr_bits(spi, STM32F4_SPI_CR2, STM32F4_SPI_CR2_RXDMAEN);
+
+ spin_unlock_irqrestore(&spi->lock, flags);
+
+ dev_info(spi->dev, "DMA issue: fall back to irq transfer\n");
+
+ return stm32f4_spi_transfer_one_irq(spi);
+}
+
+/**
+ * stm32f4_spi_transfer_one_setup - common setup to transfer a single
+ * spi_transfer either using DMA or
+ * interrupts.
+ */
+static int stm32f4_spi_transfer_one_setup(struct stm32f4_spi *spi,
+ struct spi_device *spi_dev,
+ struct spi_transfer *transfer)
+{
+ unsigned long flags;
+ u32 cr1_clrb = 0, cr1_setb = 0;
+ u32 nb_words;
+ int ret = 0;
+
+ spin_lock_irqsave(&spi->lock, flags);
+
+ if (spi->cur_bpw != transfer->bits_per_word) {
+ spi->cur_bpw = transfer->bits_per_word;
+ nb_words = spi->cur_bpw;
+ cr1_clrb |= STM32F4_SPI_CR1_DFF;
+
+ if (spi->cur_bpw == 16)
+ cr1_setb |= STM32F4_SPI_CR1_DFF;
+ }
+
+ if (spi->cur_speed != transfer->speed_hz) {
+ int mbr;
+
+ /* Update spi->cur_speed with real clock speed */
+ mbr = stm32f4_spi_prepare_mbr(spi, transfer->speed_hz);
+ if (mbr < 0) {
+ ret = mbr;
+ goto out;
+ }
+
+ transfer->speed_hz = spi->cur_speed;
+
+ cr1_clrb |= STM32F4_SPI_CR1_BR;
+ cr1_setb |= ((u32)mbr << STM32F4_SPI_CR1_BR_SHIFT) &
+ STM32F4_SPI_CR1_BR;
+ }
+
+ if (cr1_clrb || cr1_setb)
+ writel_relaxed((readl_relaxed(spi->base + STM32F4_SPI_CR1) &
+ ~cr1_clrb) | cr1_setb,
+ spi->base + STM32F4_SPI_CR1);
+
+ spi->cur_xferlen = transfer->len;
+
+ dev_dbg(spi->dev, "full-duplex communication mode\n");
+ dev_dbg(spi->dev, "data frame of %d-bit\n", spi->cur_bpw);
+ dev_dbg(spi->dev, "speed set to %dHz\n", spi->cur_speed);
+ dev_dbg(spi->dev, "transfer of %d bytes (%d data frames)\n",
+ spi->cur_xferlen, nb_words);
+ dev_dbg(spi->dev, "dma %s\n",
+ (spi->cur_usedma) ? "enabled" : "disabled");
+
+out:
+ spin_unlock_irqrestore(&spi->lock, flags);
+
+ return ret;
+}
+
+/**
+ * stm32f4_spi_transfer_one - transfer a single spi_transfer
+ *
+ * It must return 0 if the transfer is finished or 1 if the transfer is still
+ * in progress.
+ */
+static int stm32f4_spi_transfer_one(struct spi_master *master,
+ struct spi_device *spi_dev,
+ struct spi_transfer *transfer)
+{
+ struct stm32f4_spi *spi = spi_master_get_devdata(master);
+ int ret;
+
+ spi->tx_buf = transfer->tx_buf;
+ spi->rx_buf = transfer->rx_buf;
+ spi->tx_len = spi->tx_buf ? transfer->len : 0;
+ spi->rx_len = spi->rx_buf ? transfer->len : 0;
+
+ spi->cur_usedma = (master->can_dma &&
+ stm32f4_spi_can_dma(master, spi_dev, transfer));
+
+ ret = stm32f4_spi_transfer_one_setup(spi, spi_dev, transfer);
+ if (ret) {
+ dev_err(spi->dev, "SPI transfer setup failed\n");
+ return ret;
+ }
+
+ if (spi->cur_usedma)
+ return stm32f4_spi_transfer_one_dma(spi, transfer);
+ else
+ return stm32f4_spi_transfer_one_irq(spi);
+}
+
+/**
+ * stm32f4_spi_unprepare_msg - relax the hardware
+ */
+static int stm32f4_spi_unprepare_msg(struct spi_master *master,
+ struct spi_message *msg)
+{
+ struct stm32f4_spi *spi = spi_master_get_devdata(master);
+
+ stm32f4_spi_disable(spi);
+
+ return 0;
+}
+
+/**
+ * stm32f4_spi_config - configure SPI controller as SPI master
+ */
+static int stm32f4_spi_config(struct stm32f4_spi *spi)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&spi->lock, flags);
+
+ /* Ensure I2SMOD bit is kept cleared */
+ stm32f4_spi_clr_bits(spi, STM32F4_SPI_I2SCFGR,
+ STM32F4_SPI_I2SCFGR_I2SMOD);
+
+ /*
+ * - SS input value high
+ * - Set the master mode (default Motorola mode)
+ * - Consider 1 master/n slaves configuration and
+ * SS input value is determined by the SSI bit
+ */
+ stm32f4_spi_set_bits(spi, STM32F4_SPI_CR1, STM32F4_SPI_CR1_SSI |
+ STM32F4_SPI_CR1_MSTR |
+ STM32F4_SPI_CR1_SSM);
+
+ spin_unlock_irqrestore(&spi->lock, flags);
+
+ return 0;
+}
+
+/**
+ * stm32f4_release_dma - release DMA tx and rx channels
+ */
+static void stm32f4_release_dma(struct spi_master *master)
+{
+ if (master->dma_tx)
+ dma_release_channel(master->dma_tx);
+ if (master->dma_rx)
+ dma_release_channel(master->dma_rx);
+}
+
+/**
+ * stm32f4_spi_dma_prep - prepare controller to use DMA tx and rx channels
+ */
+static int stm32f4_spi_dma_prep(struct stm32f4_spi *spi, struct device *dev)
+{
+ struct spi_master *master = spi->master;
+
+ master->dma_tx = dma_request_slave_channel(spi->dev, "tx");
+ if (!master->dma_tx) {
+ dev_warn(dev, "failed to request tx dma channel\n");
+ return -ENODEV;
+ }
+
+ master->dma_rx = dma_request_slave_channel(spi->dev, "rx");
+ if (!master->dma_rx) {
+ dev_warn(dev, "failed to request rx dma channel\n");
+ stm32f4_release_dma(master);
+ return -ENODEV;
+ }
+
+ master->can_dma = stm32f4_spi_can_dma;
+ dev_info(dev, "DMA available");
+ return 0;
+}
+
+static const struct of_device_id stm32f4_spi_of_match[] = {
+ { .compatible = "st,stm32f4-spi", },
+ {},
+};
+MODULE_DEVICE_TABLE(of, stm32f4_spi_of_match);
+
+static int stm32f4_spi_probe(struct platform_device *pdev)
+{
+ struct spi_master *master;
+ struct stm32f4_spi *spi;
+ struct resource *res;
+ int i, ret;
+
+ master = spi_alloc_master(&pdev->dev, sizeof(struct stm32f4_spi));
+ if (!master) {
+ dev_err(&pdev->dev, "spi master allocation failed\n");
+ return -ENOMEM;
+ }
+ platform_set_drvdata(pdev, master);
+
+ spi = spi_master_get_devdata(master);
+ spi->dev = &pdev->dev;
+ spi->master = master;
+ spin_lock_init(&spi->lock);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ spi->base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(spi->base)) {
+ ret = PTR_ERR(spi->base);
+ goto err_master_put;
+ }
+ spi->phys_addr = (dma_addr_t)res->start;
+
+ spi->irq = platform_get_irq(pdev, 0);
+ if (spi->irq <= 0) {
+ dev_err(&pdev->dev, "no irq: %d\n", spi->irq);
+ ret = -ENOENT;
+ goto err_master_put;
+ }
+ ret = devm_request_threaded_irq(&pdev->dev, spi->irq,
+ stm32f4_spi_irq_event,
+ stm32f4_spi_irq_thread,
+ IRQF_ONESHOT, pdev->name, master);
+ if (ret) {
+ dev_err(&pdev->dev, "irq%d request failed: %d\n", spi->irq,
+ ret);
+ goto err_master_put;
+ }
+
+ spi->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(spi->clk)) {
+ ret = PTR_ERR(spi->clk);
+ dev_err(&pdev->dev, "clk get failed: %d\n", ret);
+ goto err_master_put;
+ }
+
+ ret = clk_prepare_enable(spi->clk);
+ if (ret) {
+ dev_err(&pdev->dev, "clk enable failed: %d\n", ret);
+ goto err_master_put;
+ }
+ spi->clk_rate = clk_get_rate(spi->clk);
+ if (!spi->clk_rate) {
+ dev_err(&pdev->dev, "clk rate = 0\n");
+ ret = -EINVAL;
+ goto err_clk_disable;
+ }
+
+ spi->rst = devm_reset_control_get_exclusive(&pdev->dev, NULL);
+ if (!IS_ERR(spi->rst)) {
+ reset_control_assert(spi->rst);
+ udelay(2);
+ reset_control_deassert(spi->rst);
+ }
+
+ ret = stm32f4_spi_config(spi);
+ if (ret) {
+ dev_err(&pdev->dev, "controller configuration failed: %d\n",
+ ret);
+ goto err_clk_disable;
+ }
+
+ master->dev.of_node = pdev->dev.of_node;
+ master->auto_runtime_pm = true;
+ master->bus_num = pdev->id;
+ master->mode_bits = SPI_CPHA | SPI_CPOL | SPI_CS_HIGH | SPI_LSB_FIRST;
+ master->flags = SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX;
+ master->bits_per_word_mask = SPI_BPW_MASK(8) | SPI_BPW_MASK(16);
+ master->max_speed_hz = spi->clk_rate / STM32F4_SPI_BR_DIV_MIN;
+ master->min_speed_hz = spi->clk_rate / STM32F4_SPI_BR_DIV_MAX;
+ master->setup = stm32f4_spi_setup;
+ master->prepare_message = stm32f4_spi_prepare_msg;
+ master->transfer_one = stm32f4_spi_transfer_one;
+ master->unprepare_message = stm32f4_spi_unprepare_msg;
+
+ /* optional DMA support */
+ ret = stm32f4_spi_dma_prep(spi, &pdev->dev);
+ if (ret < 0)
+ dev_warn(&pdev->dev, "DMA not available, using PIO mode\n");
+
+ pm_runtime_set_active(&pdev->dev);
+ pm_runtime_enable(&pdev->dev);
+
+ ret = devm_spi_register_master(&pdev->dev, master);
+ if (ret) {
+ dev_err(&pdev->dev, "spi master registration failed: %d\n",
+ ret);
+ goto err_dma_release;
+ }
+
+ if (!master->cs_gpios) {
+ dev_err(&pdev->dev, "no CS gpios available\n");
+ ret = -EINVAL;
+ goto err_dma_release;
+ }
+
+ for (i = 0; i < master->num_chipselect; i++) {
+ if (!gpio_is_valid(master->cs_gpios[i])) {
+ dev_err(&pdev->dev, "%i is not a valid gpio\n",
+ master->cs_gpios[i]);
+ ret = -EINVAL;
+ goto err_dma_release;
+ }
+
+ ret = devm_gpio_request(&pdev->dev, master->cs_gpios[i],
+ DRIVER_NAME);
+ if (ret) {
+ dev_err(&pdev->dev, "can't get CS gpio %i\n",
+ master->cs_gpios[i]);
+ goto err_dma_release;
+ }
+ }
+
+ dev_info(&pdev->dev, "driver initialized\n");
+
+ return 0;
+
+err_dma_release:
+ stm32f4_release_dma(master);
+
+ pm_runtime_disable(&pdev->dev);
+err_clk_disable:
+ clk_disable_unprepare(spi->clk);
+err_master_put:
+ spi_master_put(master);
+
+ return ret;
+}
+
+static int stm32f4_spi_remove(struct platform_device *pdev)
+{
+ struct spi_master *master = platform_get_drvdata(pdev);
+ struct stm32f4_spi *spi = spi_master_get_devdata(master);
+
+ stm32f4_spi_disable(spi);
+
+ if (master->dma_tx)
+ dma_release_channel(master->dma_tx);
+ if (master->dma_rx)
+ dma_release_channel(master->dma_rx);
+
+ clk_disable_unprepare(spi->clk);
+
+ pm_runtime_disable(&pdev->dev);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int stm32f4_spi_runtime_suspend(struct device *dev)
+{
+ struct spi_master *master = dev_get_drvdata(dev);
+ struct stm32f4_spi *spi = spi_master_get_devdata(master);
+
+ clk_disable_unprepare(spi->clk);
+
+ return 0;
+}
+
+static int stm32f4_spi_runtime_resume(struct device *dev)
+{
+ struct spi_master *master = dev_get_drvdata(dev);
+ struct stm32f4_spi *spi = spi_master_get_devdata(master);
+
+ return clk_prepare_enable(spi->clk);
+}
+#endif
+
+#ifdef CONFIG_PM_SLEEP
+static int stm32f4_spi_suspend(struct device *dev)
+{
+ struct spi_master *master = dev_get_drvdata(dev);
+ int ret;
+
+ ret = spi_master_suspend(master);
+ if (ret)
+ return ret;
+
+ return pm_runtime_force_suspend(dev);
+}
+
+static int stm32f4_spi_resume(struct device *dev)
+{
+ struct spi_master *master = dev_get_drvdata(dev);
+ struct stm32f4_spi *spi = spi_master_get_devdata(master);
+ int ret;
+
+ ret = pm_runtime_force_resume(dev);
+ if (ret)
+ return ret;
+
+ ret = spi_master_resume(master);
+ if (ret)
+ clk_disable_unprepare(spi->clk);
+
+ return ret;
+}
+#endif
+
+static const struct dev_pm_ops stm32f4_spi_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(stm32f4_spi_suspend, stm32f4_spi_resume)
+ SET_RUNTIME_PM_OPS(stm32f4_spi_runtime_suspend,
+ stm32f4_spi_runtime_resume, NULL)
+};
+
+static struct platform_driver stm32f4_spi_driver = {
+ .probe = stm32f4_spi_probe,
+ .remove = stm32f4_spi_remove,
+ .driver = {
+ .name = DRIVER_NAME,
+ .pm = &stm32f4_spi_pm_ops,
+ .of_match_table = stm32f4_spi_of_match,
+ },
+};
+
+module_platform_driver(stm32f4_spi_driver);
+
+MODULE_ALIAS("platform:" DRIVER_NAME);
+MODULE_DESCRIPTION("STMicroelectronics STM32F4 SPI Controller driver");
+MODULE_AUTHOR("Cezary Gapinski <cezary.gapinski@xxxxxxxxx>");
+MODULE_LICENSE("GPL v2");
--
2.7.4