RE: intel_pstate: Lowest frequency not reached with Intel i7-6700

[Doug Smythies]

On 2018.12.13 04:42 Paul Menzel wrote:
> On 12/13/18 11:39, Rafael J. Wysocki wrote:
>> On Thu, Dec 13, 2018 at 10:54 AM Paul Menzel <pmenzel@xxxxxxxxxxxxx> wrote:
>>> On 12/13/18 00:06, Doug Smythies wrote:
>>>> On 2018.12.12 13:40 Paul Menzel wrote:
>>>>
>>>>> Using *powersave* as P-state selection algorithm, on an idle system
>>>>
>>>> Define "idle system".
>>>> If your computer is running a GUI, or is even a server without a GUI
>>>> but with many services running, then "idle" really isn't.
>>>> Below is from my test server, with many services disabled, so
>>>> "idle" really is quite "idle"
>>>>
>>>> doug@s15:~/temp$ sudo turbostat --Summary --quiet --show Busy%,Bzy_MHz,PkgTmp,PkgWatt --interval 15
>>>> Busy%   Bzy_MHz PkgTmp  PkgWatt
>>>> 0.01    1608    27      3.71
>>>> 0.01    1619    27      3.71
>>>> 0.01    1600    28      3.71
>>>> 0.01    1600    28      3.70
>>>>
>>>> Note that p state 16 (1600 MHz) is the minimum for my older i7-2600k
>>>> processor.
>>>
>>> The thing is, on an Intel Kaby Lake laptop with Ubuntu 18.10 and GNOME
>>> running, it goes down to the lowest listed frequency.
>
> Checking the numbers again, I was mistaken. The lowest possible frequency
> of the Intel Kaby Lake i7-7500U in that laptop is 400 MHz, and it is
> going down to 600 MHz. Busy% from turbostat is 0.3 to 0.4.
>
>> Kaby Lake has hardware-managed P-states (HWP) which is a different mechanism.
>
> Isnât HWP also available for the 6th generation?
>
>    $ dmesg | grep intel_pstate
>    [    2.092456] intel_pstate: Intel P-state driver initializing
>    [    2.094820] intel_pstate: HWP enabled

Yes, you have HWP. I do not have HWP. I don't think HWP or not is
particularly relevant to this discussion.

>>>>> Shouldnât it go down until 800 MHz?
>>>>
>>>> We would need some actual busy information, turbostat is the
>>>> recommended tool, to know for sure.
>>>
>>> Here you go.
>>>
>>> ```
>>> tools/power/x86/turbostat> sudo ./turbostat --Summary --quiet --show Busy%,Bzy_MHz,PkgTmp,PkgWatt --interval 15
>>> Busy%    Bzy_MHz    PkgTmp    PkgWatt
>>> 3.59    1167    31    1.68
>>> 3.21    903    31    1.34
>>> 3.21    906    31    1.34
>>> 3.27    901    31    1.35
>>> 8.23    2715    30    2.32  â stopping GDM (systemctl stop gdm)
>>> 2.95    915    30    1.18
>>> 2.91    906    30    1.18
>>> 2.92    903    30    1.17
>>> 2.90    900    29    1.17
>>> 2.89    903    29    1.18
>>> 2.91    903    30    1.18
>>> 2.89    903    29    1.18
>>> 2.89    900    29    1.18
>>> 2.90    903    30    1.18
>>> 2.90    903    29    1.17
>>> 2.90    903    29    1.17
>>> 2.90    900    29    1.16
>>> 2.90    903    29    1.14
>>> 2.90    903    28    1.11
>>> 2.90    903    29    1.10
>>> 2.91    900    29    1.16
>>> 2.91    903    29    1.14
>>> 2.90    903    29    1.12
>>> 2.90    903    29    1.16
>>> 2.90    900    28    1.17
>>> 2.92    903    29    1.16
>>> 2.90    903    29    1.16
>>> 2.90    903    29    1.16
>>> ```
>>>
>>> 800 MHz should be enough to keep GDM running, shouldnât it?
>> 
>> Well, depending.
>> 
>>> Otherwise only SSH was running.
>> 
>> There obviously is something that causes it to stay at 900 MHz.

Agreed. Clearly some more stuff was using some CPU.
The resulting requested CPU frequency is also highly dependent on
the frequency of the load. Example:

doug@s15:~/csv-plot$ sudo turbostat --Summary --quiet --show Busy%,Bzy_MHz,PkgTmp,PkgWatt --interval 60
Busy%   Bzy_MHz PkgTmp  PkgWatt
0.08    2567    27      3.77  <<< Note the high active CPU frequency with virtually no load.
0.01    1600    26      3.69
0.01    1600    27      3.70
0.83    1600    30      4.18
1.80    1600    30      4.59  <<< This load is at 435 Hertz work / sleep frequency
1.80    1600    32      4.59
0.74    3033    27      4.49  <<< This load is at 1 Hertz work / sleep frequency
0.76    3380    27      4.63
0.76    3384    28      4.62
0.38    3356    28      4.16
0.01    1615    28      3.71
0.01    1609    27      3.70

>
> Itâs not obvious to me, but you have more experience. Itâd expect
> to at least one core(?) to go down to 800 MHz and not all to stay
> at 900 MHz.

There is only PLL (Phase Locked Loop). The highest requested vote
for CPU frequency wins. CPUs in deep idle do not get a vote.

>> Please check max_perf_pct, min_perf_pct and num_pstates under
>> /sys/devices/system/cpu/intel_pstate/ .
>
>    /sys/devices/system/cpu/intel_pstate> cat max_perf_pct min_perf_pct num_pstates
>    100
>    20
>    33
>
>> Also cpuinfo_max_freq, cpuinfo_min_freq, scaling_max_freq,
>> scaling_min_freq under /sys/devices/system/cpu/cpufreq/policy0/ .
>
> /sys/devices/system/cpu/cpufreq/policy0> cat cpuinfo_{min,max}_freq scaling_{min,max}_freq
>    800000
>    4000000
>    800000
>    4000000
>
>> However, please note that Busy% of 3 isn't particularly low.
>
> Indeed. On the laptop it is around 0.3 to 0.4 even with GNOME
> running.
>
> So, to check if everything is working, I boot into initramfs
> and check the numbers there?
>

Myself, I think there is nothing wrong here. If you want
to pursue further, then my suggestion would be to disable
HWP and use trace and the intel_pstate_tracer.py utility
to fully analyze your "idle" system load and your systems
response to it.

... Doug