Re: [PATCH v2 11/12] drm/panel: Add Feiyang FY07024DI26A30-D MIPI-DSI LCD panel

[Sean Paul]

On Fri, Dec 14, 2018 at 04:35:11PM +0530, Jagan Teki wrote:
> On Fri, Dec 14, 2018 at 1:25 AM Sean Paul <sean@xxxxxxxxxx> wrote:
> >
> > On Fri, Dec 14, 2018 at 12:56:03AM +0530, Jagan Teki wrote:
> > > On Thu, Dec 13, 2018 at 8:37 PM Sean Paul <sean@xxxxxxxxxx> wrote:
> > > >
> > > > On Fri, Nov 16, 2018 at 10:09:15PM +0530, Jagan Teki wrote:
> > > > > Feiyang FY07024DI26A30-D is 1024x600, 4-lane MIPI-DSI LCD panel.
> > > > >
> > > > > Add panel driver for it.
> > > > >
> > > > > Signed-off-by: Jagan Teki <jagan@xxxxxxxxxxxxxxxxxxxx>
> > > > > ---
> > > > >  MAINTAINERS                                   |   6 +
> > > > >  drivers/gpu/drm/panel/Kconfig                 |   9 +
> > > > >  drivers/gpu/drm/panel/Makefile                |   1 +
> > > > >  .../drm/panel/panel-feiyang-fy07024di26a30d.c | 286 ++++++++++++++++++
> > > > >  4 files changed, 302 insertions(+)
> > > > >  create mode 100644 drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c
> > > > >
> >
> > /snip
> >
> > > > > diff --git a/drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c b/drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c
> > > > > new file mode 100644
> > > > > index 000000000000..a4b46bd8fdbe
> > > > > --- /dev/null
> > > > > +++ b/drivers/gpu/drm/panel/panel-feiyang-fy07024di26a30d.c
> >
> > /snip
> >
> > > > > +static int feiyang_prepare(struct drm_panel *panel)
> > > > > +{
> > > > > +     struct feiyang *ctx = panel_to_feiyang(panel);
> > > > > +     struct mipi_dsi_device *dsi = ctx->dsi;
> > > > > +     unsigned int i;
> > > > > +     int ret;
> > > > > +
> > > > > +     ret = regulator_enable(ctx->dvdd);
> > > > > +     if (ret)
> > > > > +             return ret;
> > > > > +
> > > > > +     msleep(100);
> > > >
> > > > nit: You should do your best to correlate the sleeps with the timing parameters
> > > > from the datasheet with a comment.
> > > >
> > > > ie:
> > > >         /* T1: > 100ms */
> > > >         msleep(100);
> > >
> > > Sorry, what does this mean?
> >
> > On page 9 of the datasheet you sent me [1], it has the delays required to safely
> > power up the panel. This delay is the time between dvdd going high and avdd
> > going high. On the figure in the datasheet, this would be T2 (T1 is dvdd rise
> 
> time between dvdd going high and avdd going high is T1 + T3 right?
> 
> T2 > 0ms
> T3 > 20ms
> 
> In this case the delay can be msleep(20) ?

Hmm, yeah, I didn't notice that T3 was > 20ms, that's kind of confusing. So I
think you're right, this should be T2 + T3 > 20ms (T1 is covered in the
regulator_enable of dvdd).

> 
> > time and should be handled in the regulator subsystem (iirc)). Also according to
> > the datasheet, T2 just needs to be > 0, so you don't even need this delay. You
> > could replace this with a comment like:
> >
> >         /* T1 (dvdd rise time) + T2 (dvdd->avdd) > 0 */
> >
> > So for all of the msleeps below you should get the delays from the datasheet and
> > add a comment referencing them.
> 
> T5 and T6 are delay between avdd to reset enable it can be 10 + 10
> =&gt; 20ms and finally T12 which is 200 after reset.
> 
> What about the delay between resets, I need to understand it a bit.

These are usually accounted for at the end of disable. Take a look at the sleep
parameters in panel-simple for an example.

Sean

-- 
Sean Paul, Software Engineer, Google / Chromium OS