Re: [PATCH 11/11] dt-bindings: iio: adc: Add docs for AD7606 ADC

[Jonathan Cameron]

On Thu, 13 Dec 2018 14:46:23 +0200
Stefan Popa <stefan.popa@xxxxxxxxxx> wrote:

> Document support for AD7606 Analog to Digital Converter.
> 
> Signed-off-by: Stefan Popa <stefan.popa@xxxxxxxxxx>
> Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
Will have to wait on this as the MAINTAINERS bit obviously isn't there yet.
Otherwise I would have just added it now.  Oh well, v2.


Thanks,

Jonathan

> ---
>  .../devicetree/bindings/iio/adc/adi,ad7606.txt     | 65 ++++++++++++++++++++++
>  MAINTAINERS                                        |  1 +
>  2 files changed, 66 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
> 
> diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
> new file mode 100644
> index 0000000..d7b6241
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
> @@ -0,0 +1,65 @@
> +Analog Devices AD7606 Simultaneous Sampling ADC
> +
> +Required properties for the AD7606:
> +
> +- compatible: Must be one of
> +	* "adi,ad7605-4"
> +	* "adi,ad7606-8"
> +	* "adi,ad7606-6"
> +	* "adi,ad7606-4"
> +- reg: SPI chip select number for the device
> +- spi-max-frequency: Max SPI frequency to use
> +	see: Documentation/devicetree/bindings/spi/spi-bus.txt
> +- spi-cpha: See Documentation/devicetree/bindings/spi/spi-bus.txt
> +- avcc-supply: phandle to the Avcc power supply
> +- interrupts: IRQ line for the ADC
> +	see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
> +- adi,conversion-start-gpios: must be the device tree identifier of the CONVST pin.
> +		  This logic input is used to initiate conversions on the analog
> +		  input channels. As the line is active high, it should be marked
> +		  GPIO_ACTIVE_HIGH.
> +
> +Optional properties:
> +
> +- reset-gpios: must be the device tree identifier of the RESET pin. If specified,
> +	       it will be asserted during driver probe. As the line is active high,
> +	       it should be marked GPIO_ACTIVE_HIGH.
> +- standby-gpios: must be the device tree identifier of the STBY pin. This pin is used
> +		to place the AD7606 into one of two power-down modes, Standby mode or
> +		Shutdown mode. As the line is active low, it should be marked
> +		GPIO_ACTIVE_LOW.
> +- adi,first-data-gpios: must be the device tree identifier of the FRSTDATA pin.
> +		    The FRSTDATA output indicates when the first channel, V1, is
> +		    being read back on either the parallel, byte or serial interface.
> +		    As the line is active high, it should be marked GPIO_ACTIVE_HIGH.
> +- adi,range-gpios: must be the device tree identifier of the RANGE pin. The polarity on
> +	      this pin determines the input range of the analog input channels. If
> +	      this pin is tied to a logic high, the analog input range is Â10V for
> +	      all channels. If this pin is tied to a logic low, the analog input range
> +	      is Â5V for all channels. As the line is active high, it should be marked
> +	      GPIO_ACTIVE_HIGH.
> +- adi,oversampling-ratio-gpios: must be the device tree identifier of the over-sampling
> +				mode pins. As the line is active high, it should be marked
> +				GPIO_ACTIVE_HIGH.
> +
> +Example:
> +
> +	adc@0 {
> +		compatible = "adi,ad7606-8";
> +		reg = <0>;
> +		spi-max-frequency = <1000000>;
> +		spi-cpol;
> +
> +		avcc-supply = <&adc_vref>;
> +
> +		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> +		interrupt-parent = <&gpio>;
> +
> +		adi,conversion-start-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
> +		reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>;
> +		adi,first-data-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
> +		adi,oversampling-ratio-gpios = <&gpio 18 GPIO_ACTIVE_HIGH
> +						&gpio 23 GPIO_ACTIVE_HIGH
> +						&gpio 26 GPIO_ACTIVE_HIGH>;
> +		standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
> +	};
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 7256ce6..798e9a2 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -859,6 +859,7 @@ L:	linux-iio@xxxxxxxxxxxxxxx
>  W:	http://ez.analog.com/community/linux-device-drivers
>  S:	Supported
>  F:	drivers/iio/adc/ad7606.c
> +F:	Documentation/devicetree/bindings/iio/adc/ad7606.txt
>  
>  ANALOG DEVICES INC AD9389B DRIVER
>  M:	Hans Verkuil <hans.verkuil@xxxxxxxxx>