Re: [PATCH] arm64: dts: sdm845: Add cpufreq device node

[Taniya Das]

Hello Matthias,

On 12/21/2018 1:20 AM, Matthias Kaehlcke wrote:
> Hi Taniya,
>
> On Fri, Dec 21, 2018 at 12:48:50AM +0530, Taniya Das wrote:
> > This change adds the cpufreq node as per the bindings example for SDM845.
> >
> > Signed-off-by: Taniya Das <tdas@xxxxxxxxxxxxxx>
> > ---
> >   arch/arm64/boot/dts/qcom/sdm845.dtsi | 19 +++++++++++++++++++
> >   1 file changed, 19 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> > index 23a253b..5db4fcc 100644
> > --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> > @@ -99,6 +99,7 @@
> >   			compatible = "qcom,kryo385";
> >   			reg = <0x0 0x0>;
> >   			enable-method = "psci";
> > +			qcom,freq-domain = <&cpufreq_hw 0>;
> >   			next-level-cache = <&L2_0>;
> >   			L2_0: l2-cache {
> >   				compatible = "cache";
> > @@ -114,6 +115,7 @@
> >   			compatible = "qcom,kryo385";
> >   			reg = <0x0 0x100>;
> >   			enable-method = "psci";
> > +			qcom,freq-domain = <&cpufreq_hw 0>;
> >   			next-level-cache = <&L2_100>;
> >   			L2_100: l2-cache {
> >   				compatible = "cache";
> > @@ -126,6 +128,7 @@
> >   			compatible = "qcom,kryo385";
> >   			reg = <0x0 0x200>;
> >   			enable-method = "psci";
> > +			qcom,freq-domain = <&cpufreq_hw 0>;
> >   			next-level-cache = <&L2_200>;
> >   			L2_200: l2-cache {
> >   				compatible = "cache";
> > @@ -138,6 +141,7 @@
> >   			compatible = "qcom,kryo385";
> >   			reg = <0x0 0x300>;
> >   			enable-method = "psci";
> > +			qcom,freq-domain = <&cpufreq_hw 0>;
> >   			next-level-cache = <&L2_300>;
> >   			L2_300: l2-cache {
> >   				compatible = "cache";
> > @@ -150,6 +154,7 @@
> >   			compatible = "qcom,kryo385";
> >   			reg = <0x0 0x400>;
> >   			enable-method = "psci";
> > +			qcom,freq-domain = <&cpufreq_hw 1>;
> >   			next-level-cache = <&L2_400>;
> >   			L2_400: l2-cache {
> >   				compatible = "cache";
> > @@ -162,6 +167,7 @@
> >   			compatible = "qcom,kryo385";
> >   			reg = <0x0 0x500>;
> >   			enable-method = "psci";
> > +			qcom,freq-domain = <&cpufreq_hw 1>;
> >   			next-level-cache = <&L2_500>;
> >   			L2_500: l2-cache {
> >   				compatible = "cache";
> > @@ -174,6 +180,7 @@
> >   			compatible = "qcom,kryo385";
> >   			reg = <0x0 0x600>;
> >   			enable-method = "psci";
> > +			qcom,freq-domain = <&cpufreq_hw 1>;
> >   			next-level-cache = <&L2_600>;
> >   			L2_600: l2-cache {
> >   				compatible = "cache";
> > @@ -186,6 +193,7 @@
> >   			compatible = "qcom,kryo385";
> >   			reg = <0x0 0x700>;
> >   			enable-method = "psci";
> > +			qcom,freq-domain = <&cpufreq_hw 1>;
> >   			next-level-cache = <&L2_700>;
> >   			L2_700: l2-cache {
> >   				compatible = "cache";
> > @@ -341,6 +349,17 @@
> >   			#power-domain-cells = <1>;
> >   		};
> >
> > +		cpufreq_hw: cpufreq@17d43000 {
> > +			compatible = "qcom,cpufreq-hw";
> > +			reg = <0x17d43000 0x1400>, <0x17d45800 0x1400>;
> > +			reg-names = "freq-domain0", "freq-domain1";
> > +
> > +			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GPLL0>;
> > +			clock-names = "xo", "alternate";
> > +
> > +			#freq-domain-cells = <1>;
> > +		};
> > +
> >   		qfprom@784000 {
> >   			compatible = "qcom,qfprom";
> >   			reg = <0x784000 0x8ff>;
>
> My understanding is that the entries in the SDM845 DT are sorted by
> address. The address of the cpufreq node is 0x17d43000, hence it
> should be the last entry of the 'soc' node, after 'timer@17c90000'.
>
> Tested-by: Matthias Kaehlcke <mka@xxxxxxxxxxxx>
Thank you, updated the v2 patch.

--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation.

--