[PATCH v14] i2c: Add drivers for the AMD PCIe MP2 I2C controller

From: Elie Morisse
Date: Sat Dec 22 2018 - 12:01:54 EST


MP2 controllers have two separate busses, so may accommodate up to two I2C
adapters. Those adapters are listed in the ACPI namespace with the
"AMDI0011" HID, and probed by a platform driver.

Communication with the MP2 takes place through MMIO registers, or through
DMA for more than 32 bytes transfers.

This is major rework of the patch submitted by Nehal-bakulchandra Shah from
AMD (https://patchwork.kernel.org/patch/10597369/).

Most of the event handling of v3 was rewritten to make it work with more
than one bus (e.g on Ryzen-based Lenovo Yoga 530), and this version
contains many other improvements.

Signed-off-by: Elie Morisse <syniurge@xxxxxxxxx>
---
Changes since v1 (https://www.spinics.net/lists/linux-i2c/msg34650.html):
-> Add fix for IOMMU
-> Add dependency of ACPI
-> Add locks to avoid the crash

Changes since v2 (https://patchwork.ozlabs.org/patch/961270/):

-> fix for review comments
-> fix for more than 32 bytes write issue

Changes since v3 (https://patchwork.kernel.org/patch/10597369/) by Elie M.:

-> support more than one bus/adapter
-> support more than one slave per bus
-> use the bus speed specified by the slaves declared in the DSDT instead of
assuming speed == 400kbits/s
-> instead of kzalloc'ing a buffer for every less than 32 bytes reads, simply
use i2c_msg.buf
-> fix buffer overreads/overflows when (<=32 bytes) message lengths aren't a
multiple of 4 by using memcpy_fromio and memcpy_toio
-> use streaming DMA mappings instead of allocating a coherent DMA buffer for
every >32 bytes read/write
-> properly check for timeouts during i2c_amd_xfer and increase it from 50
jiffies to 250 msecs (which is more in line with other drivers)
-> complete amd_i2c_dev.msg even if the device doesn't return a xxx_success
event, instead of stalling i2c_amd_xfer
-> removed the spinlock and mdelay during i2c_amd_pci_configure, I didn't see
the point since it's already waiting for a i2c_busenable_complete event
-> add an adapter-specific mutex lock for i2c_amd_xfer, since we don't want
parallel calls writing to AMD_C2P_MSG0 (or AMD_C2P_MSG1)
-> add a global mutex lock for registers AMD_C2P_MSG2 to AMD_C2P_MSG9, which
are shared across the two busses/adapters
-> add MODULE_DEVICE_TABLE to automatically load i2c-amd-platdrv if the DSDT
enumerates devices with the "AMDI0011" HID
-> set maximum length of reads/writes to 4095 (event's length field is 12 bits)
-> basic PM support
-> style corrections to match the kernel code style, and tried to reduce code
duplication whenever possible

Changes since v4 by Elie M.:

-> fix missing typecast warning
-> removed the duplicated entry in Kconfig

Changes since v5 by Elie M.:

-> move DMA mapping from the platform driver to the PCI driver
-> attempt to find the platform device's PCI parent through the _DEP ACPI method
(if not found take the first MP2 device registred in the i2c-amd-pci-mp2
driver, like before)
-> do not assume anymore that the PCI device is owned by the i2c-amd-pci-mp2
driver
-> address other review comments by Bjorn Helgaas (meant for v3)

Changes since v6 by Elie M.:

-> remove unnecessary memcpy from the DMA buffer during i2c_amd_read_completion

Changes since v7 by Elie M.:

-> merge the two modules into one named i2c-amd-mp2, delete now useless exports
-> unlock the C2P mutex if i2c_amd_xfer_msg timeouts, to prevent stalling the
MP2 controller if a slave doesn't respond to a read or write request
-> unmap the DMA buffer before read/write_complete
-> fix bus_disable commands handling (no more errors during module exit)
-> prefer managed versions of pci_ and dev_ functions whenever possible
-> increase adapter retries from 0 to 3
-> reduce code duplication in debugfs functions
-> address other review points by Bjorn Helgaas (except regarding the _DEP
hint)

Changes since v8 by Elie M.:

-> remove mostly redundant amd_i2c_rw_config, refer to i2c_msg whenever
possible
-> use i2c_get_dma_safe_msg_buf and i2c_put_dma_safe_msg_buf
-> defer probe() by the platform driver if no MP2 device has been probed
yet by the PCI driver (which should address Bjorn Helgaas' concern while
preserving the platform driver)
-> if the interrupt following a command doesn't get handled after 250ms,
zero AMD_P2C_MSG_INTEN to prevent the MP2 from stalling for a few more
seconds
-> include AMD_P2C_MSG3 and fix typo in debugfs output
-> cosmetic fixes, code reduction, and better comments
-> add Nehal Shah and Shyam Sundar S K from AMD to the list of maintainers

Changes since v9 by Elie M.:

-> remove the xfer_lock mutex which was redundant with i2c_adapter.bus_lock
-> platform device remove() fixes (protection against the very unlikely
case that both the PCI and platform devices get detached manually and
simultaneously)
-> fix manually unbinding the PCI device and then rebinding, there was an
interrupt that wouldn't get serviced and thus the line got disabled
-> look for the MP2 device corresponding to an AMDI0011 ACPI device in
every device enumerated by _DEP, not just the first one
-> set i2c_adapter.nr to pdev->id and call i2c_add_numbered_adapter()
-> add Documentation/i2c/busses/ entry
-> minor enhancements

Changes since v10 by Elie M.:

-> runtime PM support
-> synchronisation fixes for <=32 bytes reads/writes through C2P registers,
no more timeouts or "irq: nobody cared" errors on Lenovo Ideapad 530s
-> remove the isr spinlock, not needed since isr aren't re-entrant
-> remove the delayed_work field, make the isr complete .cmd_complete
directly
-> xfer now returns -EIO if the MP2 response isn't the expected one
-> check that the adapter still exists at the beginning of xfer
-> less code duplication in amd_mp2_read/write
-> better names (bus_xnable => bus_enable_set, _msg => _cmd) and other
minor enhancements

Changes since v11 by Elie M.:

-> remove the ACPI _DEP hint, Nehal from AMD said that there's no plan to
have more than one MP2 device per system and this wasn't _DEP's purpose
-> use device links between the two drivers to simplify the .remove logic
-> do not hardcode the i2c adapter timeout
-> code reduction and comment fixes

Changes since v12 by Elie M.:

-> fix the two warnings by the kbuild test bot

Changes since v13 by Elie M., requested by Nehal Shah from AMD:

-> split the i2c-amd-mp2 module back into two, i2c-amd-mp2-pci and
i2c-amd-mp2-plat
-> move DMA mapping back into the platform driver

Documentation/i2c/busses/i2c-amd-mp2 | 24 +
MAINTAINERS | 8 +
drivers/i2c/busses/Kconfig | 21 +
drivers/i2c/busses/Makefile | 2 +
drivers/i2c/busses/i2c-amd-mp2-pci.c | 650 ++++++++++++++++++++++++++
drivers/i2c/busses/i2c-amd-mp2-plat.c | 390 ++++++++++++++++
drivers/i2c/busses/i2c-amd-mp2.h | 223 +++++++++
7 files changed, 1318 insertions(+)
create mode 100644 Documentation/i2c/busses/i2c-amd-mp2
create mode 100644 drivers/i2c/busses/i2c-amd-mp2-pci.c
create mode 100644 drivers/i2c/busses/i2c-amd-mp2-plat.c
create mode 100644 drivers/i2c/busses/i2c-amd-mp2.h

diff --git a/Documentation/i2c/busses/i2c-amd-mp2 b/Documentation/i2c/busses/i2c-amd-mp2
new file mode 100644
index 000000000000..4b3d4b804413
--- /dev/null
+++ b/Documentation/i2c/busses/i2c-amd-mp2
@@ -0,0 +1,24 @@
+Kernel driver i2c-amd-mp2
+
+Supported adapters:
+ * AMD MP2 PCIe interface
+
+Datasheet: not publicly available.
+
+Authors:
+ Shyam Sundar S K <Shyam-sundar.S-k@xxxxxxx>
+ Nehal Shah <nehal-bakulchandra.shah@xxxxxxx>
+ Elie Morisse <syniurge@xxxxxxxxx>
+
+Description
+-----------
+
+The MP2 is an ARM processor programmed as an I2C controller and communicating
+with the x86 host through PCI.
+
+If you see something like this:
+
+03:00.7 Non-VGA unclassified device: Advanced Micro Devices, Inc. [AMD] Device
+ 15e6
+
+in your 'lspci -v', then this driver is for your device.
diff --git a/MAINTAINERS b/MAINTAINERS
index d27401df091f..76f8b3c40132 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -808,6 +808,14 @@ F: drivers/gpu/drm/amd/include/vi_structs.h
F: drivers/gpu/drm/amd/include/v9_structs.h
F: include/uapi/linux/kfd_ioctl.h

+AMD MP2 I2C DRIVER
+M: Elie Morisse <syniurge@xxxxxxxxx>
+M: Nehal Shah <nehal-bakulchandra.shah@xxxxxxx>
+M: Shyam Sundar S K <shyam-sundar.s-k@xxxxxxx>
+L: linux-i2c@xxxxxxxxxxxxxxx
+S: Maintained
+F: drivers/i2c/busses/i2c-amd-mp2*
+
AMD POWERPLAY
M: Rex Zhu <rex.zhu@xxxxxxx>
M: Evan Quan <evan.quan@xxxxxxx>
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index f2c681971201..ef7617dd5d01 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -77,6 +77,27 @@ config I2C_AMD8111
This driver can also be built as a module. If so, the module
will be called i2c-amd8111.

+config I2C_AMD_MP2_PCI
+ tristate "AMD MP2 PCIe"
+ depends on PCI
+ help
+ If you say yes to this option, support will be included for the AMD
+ MP2 PCIe I2C adapter.
+
+ This driver can also be built as a module. If so, the module
+ will be called i2c-amd-mp2-pci.
+
+config I2C_AMD_MP2_PLATFORM
+ tristate "AMD MP2 Platform"
+ select I2C_AMD_MP2_PCI
+ depends on ACPI
+ help
+ If you say yes to this option, support will be included for the AMD
+ MP2 I2C adapter.
+
+ This driver can also be built as a module. If so, the module
+ will be called i2c-amd-mp2-plat.
+
config I2C_HIX5HD2
tristate "Hix5hd2 high-speed I2C driver"
depends on ARCH_HISI || ARCH_HIX5HD2 || COMPILE_TEST
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index 5f0cb6915969..4fa829dccf68 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -33,6 +33,8 @@ obj-$(CONFIG_I2C_POWERMAC) += i2c-powermac.o

# Embedded system I2C/SMBus host controller drivers
obj-$(CONFIG_I2C_ALTERA) += i2c-altera.o
+obj-$(CONFIG_I2C_AMD_MP2_PCI) += i2c-amd-mp2-pci.o
+obj-$(CONFIG_I2C_AMD_MP2_PLATFORM) += i2c-amd-mp2-plat.o
obj-$(CONFIG_I2C_ASPEED) += i2c-aspeed.o
obj-$(CONFIG_I2C_AT91) += i2c-at91.o
obj-$(CONFIG_I2C_AU1550) += i2c-au1550.o
diff --git a/drivers/i2c/busses/i2c-amd-mp2-pci.c b/drivers/i2c/busses/i2c-amd-mp2-pci.c
new file mode 100644
index 000000000000..3abbb673acd3
--- /dev/null
+++ b/drivers/i2c/busses/i2c-amd-mp2-pci.c
@@ -0,0 +1,650 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+/*
+ * AMD MP2 PCIe communication driver
+ *
+ * Authors: Shyam Sundar S K <Shyam-sundar.S-k@xxxxxxx>
+ * Elie Morisse <syniurge@xxxxxxxxx>
+ */
+
+#include <linux/debugfs.h>
+#include <linux/dma-mapping.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/slab.h>
+
+#include "i2c-amd-mp2.h"
+
+#define DRIVER_NAME "i2c_amd_mp2"
+#define DRIVER_DESC "AMD(R) PCI-E MP2 I2C Controller Driver"
+#define DRIVER_VER "1.0"
+
+static inline void write64(u64 val, void __iomem *mmio)
+{
+ writel(val, mmio);
+ writel(val >> 32, mmio + sizeof(u32));
+}
+
+static inline u64 read64(void __iomem *mmio)
+{
+ u64 low, high;
+
+ low = readl(mmio);
+ high = readl(mmio + sizeof(u32));
+ return low | (high << 32);
+}
+
+static void amd_mp2_c2p_mutex_lock(struct amd_i2c_common *i2c_common)
+{
+ struct amd_mp2_dev *privdata = i2c_common->mp2_dev;
+
+ /* there is only one data mailbox for two i2c adapters */
+ mutex_lock(&privdata->c2p_lock);
+ privdata->c2p_lock_busid = i2c_common->bus_id;
+}
+
+static void amd_mp2_c2p_mutex_unlock(struct amd_i2c_common *i2c_common)
+{
+ struct amd_mp2_dev *privdata = i2c_common->mp2_dev;
+
+ if (unlikely(privdata->c2p_lock_busid != i2c_common->bus_id)) {
+ dev_warn(ndev_dev(privdata),
+ "bus %d attempting to unlock C2P locked by bus %d\n",
+ i2c_common->bus_id, privdata->c2p_lock_busid);
+ return;
+ }
+
+ mutex_unlock(&privdata->c2p_lock);
+}
+
+static int amd_mp2_cmd(struct amd_i2c_common *i2c_common,
+ union i2c_cmd_base i2c_cmd_base)
+{
+ struct amd_mp2_dev *privdata = i2c_common->mp2_dev;
+ void __iomem *reg;
+
+ i2c_common->reqcmd = i2c_cmd_base.s.i2c_cmd;
+
+ reg = privdata->mmio + ((i2c_cmd_base.s.bus_id == 1) ?
+ AMD_C2P_MSG1 : AMD_C2P_MSG0);
+ writel(i2c_cmd_base.ul, reg);
+
+ return 0;
+}
+
+int amd_mp2_bus_enable_set(struct amd_i2c_common *i2c_common, bool enable)
+{
+ struct amd_mp2_dev *privdata = i2c_common->mp2_dev;
+ union i2c_cmd_base i2c_cmd_base;
+
+ dev_dbg(ndev_dev(privdata), "%s id: %d\n", __func__,
+ i2c_common->bus_id);
+
+ i2c_cmd_base.ul = 0;
+ i2c_cmd_base.s.i2c_cmd = enable ? i2c_enable : i2c_disable;
+ i2c_cmd_base.s.bus_id = i2c_common->bus_id;
+ i2c_cmd_base.s.i2c_speed = i2c_common->i2c_speed;
+
+ amd_mp2_c2p_mutex_lock(i2c_common);
+
+ return amd_mp2_cmd(i2c_common, i2c_cmd_base);
+}
+EXPORT_SYMBOL_GPL(amd_mp2_bus_enable_set);
+
+static void amd_mp2_cmd_rw_fill(struct amd_i2c_common *i2c_common,
+ union i2c_cmd_base *i2c_cmd_base,
+ enum i2c_cmd reqcmd)
+{
+ i2c_cmd_base->s.i2c_cmd = reqcmd;
+ i2c_cmd_base->s.bus_id = i2c_common->bus_id;
+ i2c_cmd_base->s.i2c_speed = i2c_common->i2c_speed;
+ i2c_cmd_base->s.slave_addr = i2c_common->msg->addr;
+ i2c_cmd_base->s.length = i2c_common->msg->len;
+}
+
+static int amd_mp2_rw(struct amd_i2c_common *i2c_common, enum i2c_cmd reqcmd)
+{
+ struct amd_mp2_dev *privdata = i2c_common->mp2_dev;
+ union i2c_cmd_base i2c_cmd_base;
+
+ amd_mp2_cmd_rw_fill(i2c_common, &i2c_cmd_base, reqcmd);
+ amd_mp2_c2p_mutex_lock(i2c_common);
+
+ if (i2c_common->msg->len <= 32) {
+ i2c_cmd_base.s.mem_type = use_c2pmsg;
+ if (reqcmd == i2c_write)
+ memcpy_toio(privdata->mmio + AMD_C2P_MSG2,
+ i2c_common->msg->buf,
+ i2c_common->msg->len);
+ } else {
+ i2c_cmd_base.s.mem_type = use_dram;
+ write64((u64)i2c_common->dma_addr,
+ privdata->mmio + AMD_C2P_MSG2);
+ }
+
+ return amd_mp2_cmd(i2c_common, i2c_cmd_base);
+}
+
+int amd_mp2_read(struct amd_i2c_common *i2c_common)
+{
+ struct amd_mp2_dev *privdata = i2c_common->mp2_dev;
+
+ dev_dbg(ndev_dev(privdata), "%s addr: %x id: %d\n", __func__,
+ i2c_common->msg->addr, i2c_common->bus_id);
+
+ return amd_mp2_rw(i2c_common, i2c_read);
+}
+EXPORT_SYMBOL_GPL(amd_mp2_read);
+
+int amd_mp2_write(struct amd_i2c_common *i2c_common)
+{
+ struct amd_mp2_dev *privdata = i2c_common->mp2_dev;
+
+ dev_dbg(ndev_dev(privdata), "%s addr: %x id: %d\n", __func__,
+ i2c_common->msg->addr, i2c_common->bus_id);
+
+ return amd_mp2_rw(i2c_common, i2c_write);
+}
+EXPORT_SYMBOL_GPL(amd_mp2_write);
+
+static void amd_mp2_pci_check_rw_event(struct amd_i2c_common *i2c_common)
+{
+ struct amd_mp2_dev *privdata = i2c_common->mp2_dev;
+ int len = i2c_common->eventval.r.length;
+ u32 slave_addr = i2c_common->eventval.r.slave_addr;
+ bool err = false;
+
+ if (unlikely(len != i2c_common->msg->len)) {
+ dev_err(ndev_dev(privdata),
+ "length %d in event doesn't match buffer length %d!\n",
+ len, i2c_common->msg->len);
+ err = true;
+ }
+
+ if (unlikely(slave_addr != i2c_common->msg->addr)) {
+ dev_err(ndev_dev(privdata),
+ "unexpected slave address %x (expected: %x)!\n",
+ slave_addr, i2c_common->msg->addr);
+ err = true;
+ }
+
+ if (!err)
+ i2c_common->cmd_success = true;
+}
+
+static void __amd_mp2_process_event(struct amd_i2c_common *i2c_common)
+{
+ struct amd_mp2_dev *privdata = i2c_common->mp2_dev;
+ enum status_type sts = i2c_common->eventval.r.status;
+ enum response_type res = i2c_common->eventval.r.response;
+ int len = i2c_common->eventval.r.length;
+
+ if (res != command_success) {
+ if (res == command_failed)
+ dev_err(ndev_dev(privdata), "i2c command failed!\n");
+ else
+ dev_err(ndev_dev(privdata), "invalid response to i2c command!\n");
+ return;
+ }
+
+ switch (i2c_common->reqcmd) {
+ case i2c_read:
+ if (sts == i2c_readcomplete_event) {
+ amd_mp2_pci_check_rw_event(i2c_common);
+ if (len <= 32)
+ memcpy_fromio(i2c_common->msg->buf,
+ privdata->mmio + AMD_C2P_MSG2,
+ i2c_common->msg->len);
+ } else if (sts == i2c_readfail_event) {
+ dev_err(ndev_dev(privdata), "i2c read failed!\n");
+ } else {
+ dev_err(ndev_dev(privdata),
+ "invalid i2c status after read (%d)!\n", sts);
+ }
+ break;
+ case i2c_write:
+ if (sts == i2c_writecomplete_event)
+ amd_mp2_pci_check_rw_event(i2c_common);
+ else if (sts == i2c_writefail_event)
+ dev_err(ndev_dev(privdata), "i2c write failed!\n");
+ else
+ dev_err(ndev_dev(privdata),
+ "invalid i2c status after write (%d)!\n", sts);
+ break;
+ case i2c_enable:
+ if (sts == i2c_busenable_failed)
+ dev_err(ndev_dev(privdata), "i2c bus enable failed!\n");
+ else if (sts != i2c_busenable_complete)
+ dev_err(ndev_dev(privdata),
+ "invalid i2c status after bus enable (%d)!\n",
+ sts);
+ else
+ i2c_common->cmd_success = true;
+ break;
+ case i2c_disable:
+ if (sts == i2c_busdisable_failed)
+ dev_err(ndev_dev(privdata), "i2c bus disable failed!\n");
+ else if (sts != i2c_busdisable_complete)
+ dev_err(ndev_dev(privdata),
+ "invalid i2c status after bus disable (%d)!\n",
+ sts);
+ else
+ i2c_common->cmd_success = true;
+ break;
+ default:
+ break;
+ }
+}
+
+void amd_mp2_process_event(struct amd_i2c_common *i2c_common)
+{
+ struct amd_mp2_dev *privdata = i2c_common->mp2_dev;
+
+ if (unlikely(i2c_common->reqcmd == i2c_none)) {
+ dev_warn(ndev_dev(privdata),
+ "received msg but no cmd was sent (bus = %d)!\n",
+ i2c_common->bus_id);
+ return;
+ }
+
+ __amd_mp2_process_event(i2c_common);
+
+ i2c_common->reqcmd = i2c_none;
+ amd_mp2_c2p_mutex_unlock(i2c_common);
+}
+EXPORT_SYMBOL_GPL(amd_mp2_process_event);
+
+static irqreturn_t amd_mp2_irq_isr(int irq, void *dev)
+{
+ struct amd_mp2_dev *privdata = dev;
+ struct amd_i2c_common *i2c_common;
+ u32 val;
+ unsigned int bus_id;
+ void __iomem *reg;
+ enum irqreturn ret = IRQ_NONE;
+
+ for (bus_id = 0; bus_id < 2; bus_id++) {
+ i2c_common = privdata->busses[bus_id];
+ if (!i2c_common)
+ continue;
+
+ reg = privdata->mmio + ((bus_id == 0) ?
+ AMD_P2C_MSG1 : AMD_P2C_MSG2);
+ val = readl(reg);
+ if (val != 0) {
+ writel(0, reg);
+ writel(0, privdata->mmio + AMD_P2C_MSG_INTEN);
+ i2c_common->eventval.ul = val;
+ i2c_common->cmd_completion(i2c_common);
+
+ ret = IRQ_HANDLED;
+ }
+ }
+
+ if (ret != IRQ_HANDLED) {
+ val = readl(privdata->mmio + AMD_P2C_MSG_INTEN);
+ if (unlikely(val != 0)) {
+ writel(0, privdata->mmio + AMD_P2C_MSG_INTEN);
+ dev_warn(ndev_dev(privdata),
+ "received irq without message\n");
+ ret = IRQ_HANDLED;
+ }
+ }
+
+ return ret;
+}
+
+void amd_mp2_rw_timeout(struct amd_i2c_common *i2c_common)
+{
+ i2c_common->reqcmd = i2c_none;
+ amd_mp2_c2p_mutex_unlock(i2c_common);
+}
+EXPORT_SYMBOL_GPL(amd_mp2_rw_timeout);
+
+int amd_mp2_register_cb(struct amd_i2c_common *i2c_common)
+{
+ struct amd_mp2_dev *privdata = i2c_common->mp2_dev;
+
+ if (i2c_common->bus_id > 1)
+ return -EINVAL;
+
+ if (privdata->busses[i2c_common->bus_id]) {
+ dev_err(ndev_dev(privdata),
+ "Bus %d already taken!\n", i2c_common->bus_id);
+ return -EINVAL;
+ }
+
+ privdata->busses[i2c_common->bus_id] = i2c_common;
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(amd_mp2_register_cb);
+
+int amd_mp2_unregister_cb(struct amd_i2c_common *i2c_common)
+{
+ struct amd_mp2_dev *privdata = i2c_common->mp2_dev;
+
+ privdata->busses[i2c_common->bus_id] = NULL;
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(amd_mp2_unregister_cb);
+
+#ifdef CONFIG_DEBUG_FS
+static const struct file_operations amd_mp2_debugfs_info;
+static struct dentry *debugfs_root_dir;
+
+static ssize_t amd_mp2_debugfs_read(struct file *filp, char __user *ubuf,
+ size_t count, loff_t *offp)
+{
+ struct amd_mp2_dev *privdata = filp->private_data;
+ size_t buf_size = min_t(size_t, count, 0x800);
+ u8 *buf;
+ ssize_t ret, off = 0;
+ u32 v32;
+ int i;
+
+ buf = kmalloc(buf_size, GFP_KERNEL);
+ if (!buf)
+ return -ENOMEM;
+
+ off += scnprintf(buf + off, buf_size - off,
+ "MP2 Device Information:\n"
+ "========================\n"
+ "\tMP2 C2P Message Register Dump:\n\n");
+
+ for (i = 0; i < 10; i++) {
+ v32 = readl(privdata->mmio + AMD_C2P_MSG0 + i * 4);
+ off += scnprintf(buf + off, buf_size - off,
+ "AMD_C2P_MSG%d -\t\t\t%#06x\n", i, v32);
+ }
+
+ off += scnprintf(buf + off, buf_size - off,
+ "\n\tMP2 P2C Message Register Dump:\n\n");
+
+ for (i = 0; i < 3; i++) {
+ v32 = readl(privdata->mmio + AMD_P2C_MSG1 + i * 4);
+ off += scnprintf(buf + off, buf_size - off,
+ "AMD_P2C_MSG%d -\t\t\t%#06x\n", i + 1, v32);
+ }
+
+ v32 = readl(privdata->mmio + AMD_P2C_MSG_INTEN);
+ off += scnprintf(buf + off, buf_size - off,
+ "AMD_P2C_MSG_INTEN -\t\t%#06x\n", v32);
+
+ v32 = readl(privdata->mmio + AMD_P2C_MSG_INTSTS);
+ off += scnprintf(buf + off, buf_size - off,
+ "AMD_P2C_MSG_INTSTS -\t\t%#06x\n", v32);
+
+ ret = simple_read_from_buffer(ubuf, count, offp, buf, off);
+ kfree(buf);
+ return ret;
+}
+
+static const struct file_operations amd_mp2_debugfs_info = {
+ .owner = THIS_MODULE,
+ .open = simple_open,
+ .read = amd_mp2_debugfs_read,
+};
+
+static void amd_mp2_init_debugfs(struct amd_mp2_dev *privdata)
+{
+ if (!debugfs_root_dir)
+ return;
+
+ privdata->debugfs_dir = debugfs_create_dir(ndev_name(privdata),
+ debugfs_root_dir);
+ if (!privdata->debugfs_dir) {
+ privdata->debugfs_info = NULL;
+ } else {
+ privdata->debugfs_info = debugfs_create_file
+ ("info", 0400, privdata->debugfs_dir,
+ privdata, &amd_mp2_debugfs_info);
+ }
+}
+#endif /* CONFIG_DEBUG_FS */
+
+static void amd_mp2_clear_reg(struct amd_mp2_dev *privdata)
+{
+ int reg;
+
+ for (reg = AMD_C2P_MSG0; reg <= AMD_C2P_MSG9; reg += 4)
+ writel(0, privdata->mmio + reg);
+
+ for (reg = AMD_P2C_MSG1; reg <= AMD_P2C_MSG2; reg += 4)
+ writel(0, privdata->mmio + reg);
+}
+
+static int amd_mp2_pci_init(struct amd_mp2_dev *privdata,
+ struct pci_dev *pci_dev)
+{
+ int rc;
+
+ pci_set_drvdata(pci_dev, privdata);
+
+ rc = pcim_enable_device(pci_dev);
+ if (rc) {
+ dev_err(ndev_dev(privdata), "Failed to enable MP2 PCI device\n");
+ goto err_pci_enable;
+ }
+
+ rc = pcim_iomap_regions(pci_dev, 1 << 2, pci_name(pci_dev));
+ if (rc) {
+ dev_err(ndev_dev(privdata), "I/O memory remapping failed\n");
+ goto err_pci_enable;
+ }
+ privdata->mmio = pcim_iomap_table(pci_dev)[2];
+
+ pci_set_master(pci_dev);
+
+ rc = pci_set_dma_mask(pci_dev, DMA_BIT_MASK(64));
+ if (rc) {
+ rc = pci_set_dma_mask(pci_dev, DMA_BIT_MASK(32));
+ if (rc)
+ goto err_dma_mask;
+ }
+
+ /* Set up intx irq */
+ writel(0, privdata->mmio + AMD_P2C_MSG_INTEN);
+ pci_intx(pci_dev, 1);
+ rc = devm_request_irq(&pci_dev->dev, pci_dev->irq, amd_mp2_irq_isr,
+ IRQF_SHARED, dev_name(&pci_dev->dev), privdata);
+ if (rc)
+ dev_err(&pci_dev->dev, "Failure requesting irq %i: %d\n",
+ pci_dev->irq, rc);
+
+ return rc;
+
+err_dma_mask:
+ pci_clear_master(pci_dev);
+err_pci_enable:
+ pci_set_drvdata(pci_dev, NULL);
+ return rc;
+}
+
+static int amd_mp2_pci_probe(struct pci_dev *pci_dev,
+ const struct pci_device_id *id)
+{
+ struct amd_mp2_dev *privdata;
+ int rc;
+ static bool first_probe = true;
+
+ if (first_probe) {
+ pr_info("%s: %s Version: %s\n", DRIVER_NAME,
+ DRIVER_DESC, DRIVER_VER);
+ first_probe = false;
+ }
+
+ dev_info(&pci_dev->dev, "MP2 device found [%04x:%04x] (rev %x)\n",
+ pci_dev->vendor, pci_dev->device, pci_dev->revision);
+
+ privdata = devm_kzalloc(&pci_dev->dev, sizeof(*privdata), GFP_KERNEL);
+ if (!privdata)
+ return -ENOMEM;
+
+ rc = amd_mp2_pci_init(privdata, pci_dev);
+ if (rc)
+ return rc;
+
+ mutex_init(&privdata->c2p_lock);
+ privdata->pci_dev = pci_dev;
+
+ pm_runtime_set_autosuspend_delay(&pci_dev->dev, 1000);
+ pm_runtime_use_autosuspend(&pci_dev->dev);
+ pm_runtime_put_autosuspend(&pci_dev->dev);
+ pm_runtime_allow(&pci_dev->dev);
+
+ amd_mp2_init_debugfs(privdata);
+ dev_info(&pci_dev->dev, "MP2 device registered.\n");
+ return 0;
+}
+
+static bool amd_mp2_pci_is_probed(struct pci_dev *pci_dev)
+{
+ struct amd_mp2_dev *privdata = pci_get_drvdata(pci_dev);
+
+ if (!privdata)
+ return false;
+ return privdata->pci_dev != NULL;
+}
+
+static void amd_mp2_pci_remove(struct pci_dev *pci_dev)
+{
+ struct amd_mp2_dev *privdata = pci_get_drvdata(pci_dev);
+
+ pm_runtime_forbid(&pci_dev->dev);
+ pm_runtime_get_noresume(&pci_dev->dev);
+
+#ifdef CONFIG_DEBUG_FS
+ debugfs_remove_recursive(privdata->debugfs_dir);
+#endif /* CONFIG_DEBUG_FS */
+
+ pci_intx(pci_dev, 0);
+ pci_clear_master(pci_dev);
+
+ amd_mp2_clear_reg(privdata);
+}
+
+#ifdef CONFIG_PM
+static int amd_mp2_pci_suspend(struct device *dev)
+{
+ struct pci_dev *pci_dev = to_pci_dev(dev);
+ struct amd_mp2_dev *privdata = pci_get_drvdata(pci_dev);
+ struct amd_i2c_common *i2c_common;
+ unsigned int bus_id;
+ int ret = 0;
+
+ for (bus_id = 0; bus_id < 2; bus_id++) {
+ i2c_common = privdata->busses[bus_id];
+ if (i2c_common)
+ i2c_common->suspend(i2c_common);
+ }
+
+ ret = pci_save_state(pci_dev);
+ if (ret) {
+ dev_err(ndev_dev(privdata),
+ "pci_save_state failed = %d\n", ret);
+ return ret;
+ }
+
+ pci_disable_device(pci_dev);
+ return ret;
+}
+
+static int amd_mp2_pci_resume(struct device *dev)
+{
+ struct pci_dev *pci_dev = to_pci_dev(dev);
+ struct amd_mp2_dev *privdata = pci_get_drvdata(pci_dev);
+ struct amd_i2c_common *i2c_common;
+ unsigned int bus_id;
+ int ret = 0;
+
+ pci_restore_state(pci_dev);
+ ret = pci_enable_device(pci_dev);
+ if (ret < 0) {
+ dev_err(ndev_dev(privdata),
+ "pci_enable_device failed = %d\n", ret);
+ return ret;
+ }
+
+ for (bus_id = 0; bus_id < 2; bus_id++) {
+ i2c_common = privdata->busses[bus_id];
+ if (i2c_common) {
+ ret = i2c_common->resume(i2c_common);
+ if (ret < 0)
+ return ret;
+ }
+ }
+
+ return ret;
+}
+
+static UNIVERSAL_DEV_PM_OPS(amd_mp2_pci_pm_ops, amd_mp2_pci_suspend,
+ amd_mp2_pci_resume, NULL);
+#endif /* CONFIG_PM */
+
+static const struct pci_device_id amd_mp2_pci_tbl[] = {
+ {PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_MP2)},
+ {0}
+};
+MODULE_DEVICE_TABLE(pci, amd_mp2_pci_tbl);
+
+static struct pci_driver amd_mp2_pci_driver = {
+ .name = DRIVER_NAME,
+ .id_table = amd_mp2_pci_tbl,
+ .probe = amd_mp2_pci_probe,
+ .remove = amd_mp2_pci_remove,
+#ifdef CONFIG_PM
+ .driver = {
+ .pm = &amd_mp2_pci_pm_ops,
+ },
+#endif
+};
+
+static int amd_mp2_device_match(struct device *dev, void *data)
+{
+ return 1;
+}
+
+struct amd_mp2_dev *amd_mp2_find_device(void)
+{
+ struct device *dev;
+ struct pci_dev *pci_dev;
+
+ dev = driver_find_device(&amd_mp2_pci_driver.driver, NULL, NULL,
+ amd_mp2_device_match);
+ if (!dev)
+ return NULL;
+
+ pci_dev = to_pci_dev(dev);
+ if (!amd_mp2_pci_is_probed(pci_dev))
+ return NULL;
+ return (struct amd_mp2_dev *)pci_get_drvdata(pci_dev);
+}
+EXPORT_SYMBOL_GPL(amd_mp2_find_device);
+
+static int __init amd_mp2_drv_init(void)
+{
+#ifdef CONFIG_DEBUG_FS
+ debugfs_root_dir = debugfs_create_dir(KBUILD_MODNAME, NULL);
+#endif /* CONFIG_DEBUG_FS */
+
+ return pci_register_driver(&amd_mp2_pci_driver);
+}
+module_init(amd_mp2_drv_init);
+
+static void __exit amd_mp2_drv_exit(void)
+{
+ pci_unregister_driver(&amd_mp2_pci_driver);
+
+#ifdef CONFIG_DEBUG_FS
+ debugfs_remove_recursive(debugfs_root_dir);
+#endif /* CONFIG_DEBUG_FS */
+}
+module_exit(amd_mp2_drv_exit);
+
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_VERSION(DRIVER_VER);
+MODULE_AUTHOR("Shyam Sundar S K <Shyam-sundar.S-k@xxxxxxx>");
+MODULE_AUTHOR("Elie Morisse <syniurge@xxxxxxxxx>");
+MODULE_LICENSE("Dual BSD/GPL");
diff --git a/drivers/i2c/busses/i2c-amd-mp2-plat.c b/drivers/i2c/busses/i2c-amd-mp2-plat.c
new file mode 100644
index 000000000000..af1db2d35897
--- /dev/null
+++ b/drivers/i2c/busses/i2c-amd-mp2-plat.c
@@ -0,0 +1,390 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+/*
+ * AMD MP2 platform driver
+ *
+ * Setup the I2C adapters enumerated in the ACPI namespace.
+ * MP2 controllers have 2 separate busses, up to 2 I2C adapters may be listed.
+ *
+ * Authors: Nehal Bakulchandra Shah <Nehal-bakulchandra.shah@xxxxxxx>
+ * Elie Morisse <syniurge@xxxxxxxxx>
+ */
+
+#include <linux/acpi.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+
+#include "i2c-amd-mp2.h"
+
+#define AMD_MP2_I2C_MAX_RW_LENGTH ((1 << 12) - 1)
+#define AMD_I2C_TIMEOUT (msecs_to_jiffies(250))
+
+/**
+ * struct amd_i2c_dev - MP2 bus/i2c adapter context
+ * @common: shared context with the MP2 PCI driver
+ * @pdev: platform driver node
+ * @adap: i2c adapter
+ * @cmd_complete: xfer completion object
+ */
+struct amd_i2c_dev {
+ struct amd_i2c_common common;
+ struct platform_device *pdev;
+ struct i2c_adapter adap;
+ struct completion cmd_complete;
+};
+
+#define amd_i2c_dev_common(__common) \
+ container_of(__common, struct amd_i2c_dev, common)
+
+static int i2c_amd_dma_map(struct amd_i2c_common *i2c_common)
+{
+ struct device *dev_pci = &i2c_common->mp2_dev->pci_dev->dev;
+ struct amd_i2c_dev *i2c_dev = amd_i2c_dev_common(i2c_common);
+ enum dma_data_direction dma_direction =
+ i2c_common->msg->flags & I2C_M_RD ?
+ DMA_FROM_DEVICE : DMA_TO_DEVICE;
+
+ i2c_common->dma_buf = i2c_get_dma_safe_msg_buf(i2c_common->msg, 0);
+ i2c_common->dma_addr = dma_map_single(dev_pci, i2c_common->dma_buf,
+ i2c_common->msg->len,
+ dma_direction);
+
+ if (unlikely(dma_mapping_error(dev_pci, i2c_common->dma_addr))) {
+ dev_err(&i2c_dev->pdev->dev,
+ "Error while mapping dma buffer %p\n",
+ i2c_common->dma_buf);
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static void i2c_amd_dma_unmap(struct amd_i2c_common *i2c_common)
+{
+ struct device *dev_pci = &i2c_common->mp2_dev->pci_dev->dev;
+ enum dma_data_direction dma_direction =
+ i2c_common->msg->flags & I2C_M_RD ?
+ DMA_FROM_DEVICE : DMA_TO_DEVICE;
+
+ dma_unmap_single(dev_pci, i2c_common->dma_addr,
+ i2c_common->msg->len, dma_direction);
+
+ i2c_put_dma_safe_msg_buf(i2c_common->dma_buf, i2c_common->msg, true);
+}
+
+static const char *i2c_amd_cmd_name(enum i2c_cmd cmd)
+{
+ switch (cmd) {
+ case i2c_read:
+ return "i2c read";
+ case i2c_write:
+ return "i2c write";
+ case i2c_enable:
+ return "bus enable";
+ case i2c_disable:
+ return "bus disable";
+ case number_of_sensor_discovered:
+ return "'number of sensors discovered' cmd";
+ case is_mp2_active:
+ return "'is mp2 active' cmd";
+ default:
+ return "invalid cmd";
+ }
+}
+
+static void i2c_amd_start_cmd(struct amd_i2c_dev *i2c_dev)
+{
+ struct amd_i2c_common *i2c_common = &i2c_dev->common;
+
+ reinit_completion(&i2c_dev->cmd_complete);
+ i2c_common->cmd_success = false;
+}
+
+static void i2c_amd_cmd_completion(struct amd_i2c_common *i2c_common)
+{
+ struct amd_i2c_dev *i2c_dev = amd_i2c_dev_common(i2c_common);
+ union i2c_event *event = &i2c_common->eventval;
+
+ if (event->r.status == i2c_readcomplete_event)
+ dev_dbg(&i2c_dev->pdev->dev, "%s readdata:%*ph\n",
+ __func__, event->r.length,
+ i2c_common->msg->buf);
+
+ complete(&i2c_dev->cmd_complete);
+}
+
+static int i2c_amd_check_cmd_completion(struct amd_i2c_dev *i2c_dev)
+{
+ struct amd_i2c_common *i2c_common = &i2c_dev->common;
+ unsigned long timeout;
+
+ timeout = wait_for_completion_timeout(&i2c_dev->cmd_complete,
+ i2c_dev->adap.timeout);
+ if (unlikely(timeout == 0)) {
+ dev_err(&i2c_dev->pdev->dev, "%s timed out\n",
+ i2c_amd_cmd_name(i2c_common->reqcmd));
+ amd_mp2_rw_timeout(i2c_common);
+ }
+
+ if ((i2c_common->reqcmd == i2c_read ||
+ i2c_common->reqcmd == i2c_write) &&
+ i2c_common->msg->len > 32)
+ i2c_amd_dma_unmap(i2c_common);
+
+ if (unlikely(timeout == 0))
+ return -ETIMEDOUT;
+
+ amd_mp2_process_event(i2c_common);
+
+ if (!i2c_common->cmd_success)
+ return -EIO;
+
+ return 0;
+}
+
+static int i2c_amd_enable_set(struct amd_i2c_dev *i2c_dev, bool enable)
+{
+ struct amd_i2c_common *i2c_common = &i2c_dev->common;
+
+ i2c_amd_start_cmd(i2c_dev);
+ amd_mp2_bus_enable_set(i2c_common, enable);
+
+ return i2c_amd_check_cmd_completion(i2c_dev);
+}
+
+static int i2c_amd_xfer_msg(struct amd_i2c_dev *i2c_dev, struct i2c_msg *pmsg)
+{
+ struct amd_i2c_common *i2c_common = &i2c_dev->common;
+
+ i2c_amd_start_cmd(i2c_dev);
+ i2c_common->msg = pmsg;
+
+ if (pmsg->len > 32)
+ if (i2c_amd_dma_map(i2c_common))
+ return -EIO;
+
+ if (pmsg->flags & I2C_M_RD)
+ amd_mp2_read(i2c_common);
+ else
+ amd_mp2_write(i2c_common);
+
+ return i2c_amd_check_cmd_completion(i2c_dev);
+}
+
+static int i2c_amd_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
+{
+ struct amd_i2c_dev *i2c_dev = i2c_get_adapdata(adap);
+ int i;
+ struct i2c_msg *pmsg;
+ int err;
+
+ /* the adapter might have been deleted while waiting for the bus lock */
+ if (unlikely(!i2c_dev->common.mp2_dev))
+ return -EINVAL;
+
+ amd_mp2_pm_runtime_get(i2c_dev->common.mp2_dev);
+
+ for (i = 0; i < num; i++) {
+ pmsg = &msgs[i];
+ err = i2c_amd_xfer_msg(i2c_dev, pmsg);
+ if (err)
+ break;
+ }
+
+ amd_mp2_pm_runtime_put(i2c_dev->common.mp2_dev);
+ return err ? err : num;
+}
+
+static u32 i2c_amd_func(struct i2c_adapter *a)
+{
+ return I2C_FUNC_I2C;
+}
+
+static const struct i2c_algorithm i2c_amd_algorithm = {
+ .master_xfer = i2c_amd_xfer,
+ .functionality = i2c_amd_func,
+};
+
+#ifdef CONFIG_PM
+static int i2c_amd_suspend(struct amd_i2c_common *i2c_common)
+{
+ struct amd_i2c_dev *i2c_dev = amd_i2c_dev_common(i2c_common);
+
+ i2c_amd_enable_set(i2c_dev, false);
+ return 0;
+}
+
+static int i2c_amd_resume(struct amd_i2c_common *i2c_common)
+{
+ struct amd_i2c_dev *i2c_dev = amd_i2c_dev_common(i2c_common);
+
+ return i2c_amd_enable_set(i2c_dev, true);
+}
+#endif
+
+static enum speed_enum i2c_amd_get_bus_speed(struct platform_device *pdev)
+{
+ u32 acpi_speed;
+ int i;
+ static const u32 supported_speeds[] = {
+ 0, 100000, 400000, 1000000, 1400000, 3400000
+ };
+
+ acpi_speed = i2c_acpi_find_bus_speed(&pdev->dev);
+ /* round down to the lowest standard speed */
+ for (i = 1; i < ARRAY_SIZE(supported_speeds); i++) {
+ if (acpi_speed < supported_speeds[i])
+ break;
+ }
+ acpi_speed = supported_speeds[i - 1];
+
+ switch (acpi_speed) {
+ case 100000:
+ return speed100k;
+ case 400000:
+ return speed400k;
+ case 1000000:
+ return speed1000k;
+ case 1400000:
+ return speed1400k;
+ case 3400000:
+ return speed3400k;
+ default:
+ return speed400k;
+ }
+}
+
+static const struct i2c_adapter_quirks amd_i2c_dev_quirks = {
+ .max_read_len = AMD_MP2_I2C_MAX_RW_LENGTH,
+ .max_write_len = AMD_MP2_I2C_MAX_RW_LENGTH,
+};
+
+static int i2c_amd_probe(struct platform_device *pdev)
+{
+ int ret;
+ struct amd_i2c_dev *i2c_dev;
+ acpi_handle handle = ACPI_HANDLE(&pdev->dev);
+ struct acpi_device *adev;
+ struct amd_mp2_dev *mp2_dev;
+ const char *uid;
+
+ if (acpi_bus_get_device(handle, &adev))
+ return -ENODEV;
+
+ /* The ACPI namespace doesn't contain information about which MP2 PCI
+ * device an AMDI0011 ACPI device is related to, so assume that there's
+ * only one MP2 PCI device per system.
+ */
+ mp2_dev = amd_mp2_find_device();
+ if (!mp2_dev)
+ /* The MP2 PCI device might get probed later */
+ return -EPROBE_DEFER;
+
+ i2c_dev = devm_kzalloc(&pdev->dev, sizeof(*i2c_dev), GFP_KERNEL);
+ if (!i2c_dev)
+ return -ENOMEM;
+
+ i2c_dev->common.mp2_dev = mp2_dev;
+ i2c_dev->pdev = pdev;
+ platform_set_drvdata(pdev, i2c_dev);
+
+ i2c_dev->common.cmd_completion = &i2c_amd_cmd_completion;
+ i2c_dev->common.suspend = &i2c_amd_suspend;
+ i2c_dev->common.resume = &i2c_amd_resume;
+
+ uid = adev->pnp.unique_id;
+ if (!uid) {
+ dev_err(&pdev->dev, "missing UID/bus id!\n");
+ return -EINVAL;
+ } else if (strcmp(uid, "0") == 0) {
+ i2c_dev->common.bus_id = 0;
+ } else if (strcmp(uid, "1") == 0) {
+ i2c_dev->common.bus_id = 1;
+ } else {
+ dev_err(&pdev->dev, "incorrect UID/bus id \"%s\"!\n", uid);
+ return -EINVAL;
+ }
+ dev_dbg(&pdev->dev, "bus id is %u\n", i2c_dev->common.bus_id);
+
+ /* Register the adapter */
+ amd_mp2_pm_runtime_get(mp2_dev);
+
+ i2c_dev->common.reqcmd = i2c_none;
+ if (amd_mp2_register_cb(&i2c_dev->common))
+ return -EINVAL;
+ device_link_add(&i2c_dev->pdev->dev, &mp2_dev->pci_dev->dev,
+ DL_FLAG_AUTOREMOVE_CONSUMER);
+
+ i2c_dev->common.i2c_speed = i2c_amd_get_bus_speed(pdev);
+
+ /* Setup i2c adapter description */
+ i2c_dev->adap.owner = THIS_MODULE;
+ i2c_dev->adap.algo = &i2c_amd_algorithm;
+ i2c_dev->adap.quirks = &amd_i2c_dev_quirks;
+ i2c_dev->adap.dev.parent = &pdev->dev;
+ i2c_dev->adap.algo_data = i2c_dev;
+ i2c_dev->adap.nr = pdev->id;
+ i2c_dev->adap.timeout = AMD_I2C_TIMEOUT;
+ ACPI_COMPANION_SET(&i2c_dev->adap.dev, ACPI_COMPANION(&pdev->dev));
+ i2c_dev->adap.dev.of_node = pdev->dev.of_node;
+ snprintf(i2c_dev->adap.name, sizeof(i2c_dev->adap.name),
+ "AMD MP2 i2c bus %u", i2c_dev->common.bus_id);
+ i2c_set_adapdata(&i2c_dev->adap, i2c_dev);
+
+ init_completion(&i2c_dev->cmd_complete);
+
+ /* Enable the bus */
+ if (i2c_amd_enable_set(i2c_dev, true))
+ dev_err(&pdev->dev, "initial bus enable failed\n");
+
+ /* Attach to the i2c layer */
+ ret = i2c_add_numbered_adapter(&i2c_dev->adap);
+
+ amd_mp2_pm_runtime_put(mp2_dev);
+
+ if (ret < 0)
+ dev_err(&pdev->dev, "i2c add adapter failed = %d\n", ret);
+
+ return ret;
+}
+
+static int i2c_amd_remove(struct platform_device *pdev)
+{
+ struct amd_i2c_dev *i2c_dev = platform_get_drvdata(pdev);
+ struct amd_i2c_common *i2c_common = &i2c_dev->common;
+
+ i2c_lock_bus(&i2c_dev->adap, I2C_LOCK_ROOT_ADAPTER);
+
+ i2c_amd_enable_set(i2c_dev, false);
+ amd_mp2_unregister_cb(i2c_common);
+ i2c_common->mp2_dev = NULL;
+
+ i2c_unlock_bus(&i2c_dev->adap, I2C_LOCK_ROOT_ADAPTER);
+
+ i2c_del_adapter(&i2c_dev->adap);
+ return 0;
+}
+
+static const struct acpi_device_id i2c_amd_acpi_match[] = {
+ { "AMDI0011" },
+ { },
+};
+MODULE_DEVICE_TABLE(acpi, i2c_amd_acpi_match);
+
+static struct platform_driver i2c_amd_plat_driver = {
+ .probe = i2c_amd_probe,
+ .remove = i2c_amd_remove,
+ .driver = {
+ .name = "i2c_amd_mp2",
+ .acpi_match_table = ACPI_PTR(i2c_amd_acpi_match),
+ },
+};
+module_platform_driver(i2c_amd_plat_driver);
+
+MODULE_DESCRIPTION("AMD(R) MP2 I2C Platform Driver");
+MODULE_VERSION("1.0");
+MODULE_AUTHOR("Nehal Shah <nehal-bakulchandra.shah@xxxxxxx>");
+MODULE_AUTHOR("Elie Morisse <syniurge@xxxxxxxxx>");
+MODULE_LICENSE("Dual BSD/GPL");
diff --git a/drivers/i2c/busses/i2c-amd-mp2.h b/drivers/i2c/busses/i2c-amd-mp2.h
new file mode 100644
index 000000000000..aff9a4e4369e
--- /dev/null
+++ b/drivers/i2c/busses/i2c-amd-mp2.h
@@ -0,0 +1,223 @@
+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
+/*
+ * AMD MP2 I2C adapter driver
+ *
+ * Authors: Shyam Sundar S K <Shyam-sundar.S-k@xxxxxxx>
+ * Elie Morisse <syniurge@xxxxxxxxx>
+ */
+
+#ifndef I2C_AMD_PCI_MP2_H
+#define I2C_AMD_PCI_MP2_H
+
+#include <linux/i2c.h>
+#include <linux/pci.h>
+#include <linux/pm_runtime.h>
+
+#define PCI_DEVICE_ID_AMD_MP2 0x15E6
+
+struct amd_i2c_common;
+struct amd_mp2_dev;
+
+enum {
+ /* MP2 C2P Message Registers */
+ AMD_C2P_MSG0 = 0x10500, /* MP2 Message for I2C0 */
+ AMD_C2P_MSG1 = 0x10504, /* MP2 Message for I2C1 */
+ AMD_C2P_MSG2 = 0x10508, /* DRAM Address Lo / Data 0 */
+ AMD_C2P_MSG3 = 0x1050c, /* DRAM Address HI / Data 1 */
+ AMD_C2P_MSG4 = 0x10510, /* Data 2 */
+ AMD_C2P_MSG5 = 0x10514, /* Data 3 */
+ AMD_C2P_MSG6 = 0x10518, /* Data 4 */
+ AMD_C2P_MSG7 = 0x1051c, /* Data 5 */
+ AMD_C2P_MSG8 = 0x10520, /* Data 6 */
+ AMD_C2P_MSG9 = 0x10524, /* Data 7 */
+
+ /* MP2 P2C Message Registers */
+ AMD_P2C_MSG0 = 0x10680, /* Do not use */
+ AMD_P2C_MSG1 = 0x10684, /* I2C0 interrupt register */
+ AMD_P2C_MSG2 = 0x10688, /* I2C1 interrupt register */
+ AMD_P2C_MSG3 = 0x1068C, /* MP2 debug info */
+ AMD_P2C_MSG_INTEN = 0x10690, /* MP2 interrupt gen register */
+ AMD_P2C_MSG_INTSTS = 0x10694, /* Interrupt status */
+};
+
+/* Command register data structures */
+
+#define i2c_none (-1)
+enum i2c_cmd {
+ i2c_read = 0,
+ i2c_write,
+ i2c_enable,
+ i2c_disable,
+ number_of_sensor_discovered,
+ is_mp2_active,
+ invalid_cmd = 0xF,
+};
+
+enum speed_enum {
+ speed100k = 0,
+ speed400k = 1,
+ speed1000k = 2,
+ speed1400k = 3,
+ speed3400k = 4
+};
+
+enum mem_type {
+ use_dram = 0,
+ use_c2pmsg = 1,
+};
+
+/**
+ * union i2c_cmd_base : bit access of C2P commands
+ * @i2c_cmd: bit 0..3 i2c R/W command
+ * @bus_id: bit 4..7 i2c bus index
+ * @slave_addr: bit 8..15 slave address
+ * @length: bit 16..27 read/write length
+ * @i2c_speed: bit 28..30 bus speed
+ * @mem_type: bit 31 0-DRAM; 1-C2P msg o/p
+ */
+union i2c_cmd_base {
+ u32 ul;
+ struct {
+ enum i2c_cmd i2c_cmd : 4;
+ u8 bus_id : 4;
+ u32 slave_addr : 8;
+ u32 length : 12;
+ enum speed_enum i2c_speed : 3;
+ enum mem_type mem_type : 1;
+ } s;
+};
+
+enum response_type {
+ invalid_response = 0,
+ command_success = 1,
+ command_failed = 2,
+};
+
+enum status_type {
+ i2c_readcomplete_event = 0,
+ i2c_readfail_event = 1,
+ i2c_writecomplete_event = 2,
+ i2c_writefail_event = 3,
+ i2c_busenable_complete = 4,
+ i2c_busenable_failed = 5,
+ i2c_busdisable_complete = 6,
+ i2c_busdisable_failed = 7,
+ invalid_data_length = 8,
+ invalid_slave_address = 9,
+ invalid_i2cbus_id = 10,
+ invalid_dram_addr = 11,
+ invalid_command = 12,
+ mp2_active = 13,
+ numberof_sensors_discovered_resp = 14,
+ i2c_bus_notinitialized
+};
+
+/**
+ * union i2c_event : bit access of P2C events
+ * @response: bit 0..1 i2c response type
+ * @status: bit 2..6 status_type
+ * @mem_type: bit 7 0-DRAM; 1-C2P msg o/p
+ * @bus_id: bit 8..11 i2c bus id
+ * @length: bit 12..23 message length
+ * @slave_addr: bit 24-31 slave address
+ */
+union i2c_event {
+ u32 ul;
+ struct {
+ enum response_type response : 2;
+ enum status_type status : 5;
+ enum mem_type mem_type : 1;
+ u8 bus_id : 4;
+ u32 length : 12;
+ u32 slave_addr : 8;
+ } r;
+};
+
+/**
+ * struct amd_i2c_common - per bus/i2c adapter context, shared
+ * between the pci and the platform driver
+ * @eventval: MP2 event value set by the IRQ handler
+ * @mp2_dev: MP2 pci device this adapter is part of
+ * @msg: i2c message
+ * @cmd_completion: function called by the IRQ handler to signal
+ * the platform driver
+ * @reqcmd: requested i2c command type
+ * @cmd_success: set to true if the MP2 responded to a command with
+ * the expected status and response type
+ * @bus_id: bus index
+ * @i2c_speed: i2c bus speed determined by the slowest slave
+ * @dma_buf: if msg length > 32, holds the DMA buffer virtual address
+ * @dma_addr: if msg length > 32, holds the DMA buffer address
+ */
+struct amd_i2c_common {
+ union i2c_event eventval;
+ struct amd_mp2_dev *mp2_dev;
+ struct i2c_msg *msg;
+ void (*cmd_completion)(struct amd_i2c_common *i2c_common);
+ enum i2c_cmd reqcmd;
+ u8 cmd_success;
+ u8 bus_id;
+ enum speed_enum i2c_speed;
+ u8 *dma_buf;
+ dma_addr_t dma_addr;
+#ifdef CONFIG_PM
+ int (*suspend)(struct amd_i2c_common *i2c_common);
+ int (*resume)(struct amd_i2c_common *i2c_common);
+#endif /* CONFIG_PM */
+};
+
+/**
+ * struct amd_mp2_dev - per PCI device context
+ * @pci_dev: PCI driver node
+ * @busses: MP2 devices may have up to two busses,
+ * each bus corresponding to an i2c adapter
+ * @mmio: iommapped registers
+ * @c2p_lock: controls access to the C2P mailbox shared between
+ * the two adapters
+ * @c2p_lock_busid: id of the adapter which locked c2p_lock
+ */
+struct amd_mp2_dev {
+ struct pci_dev *pci_dev;
+ struct amd_i2c_common *busses[2];
+ void __iomem *mmio;
+ struct mutex c2p_lock;
+ u8 c2p_lock_busid;
+#ifdef CONFIG_DEBUG_FS
+ struct dentry *debugfs_dir;
+ struct dentry *debugfs_info;
+#endif /* CONFIG_DEBUG_FS */
+};
+
+#define ndev_pdev(ndev) ((ndev)->pci_dev)
+#define ndev_name(ndev) pci_name(ndev_pdev(ndev))
+#define ndev_dev(ndev) (&ndev_pdev(ndev)->dev)
+#define work_amd_i2c_common(__work) \
+ container_of(__work, struct amd_i2c_common, work.work)
+
+/* PCIe communication driver */
+
+int amd_mp2_read(struct amd_i2c_common *i2c_common);
+int amd_mp2_write(struct amd_i2c_common *i2c_common);
+int amd_mp2_bus_enable_set(struct amd_i2c_common *i2c_common, bool enable);
+
+void amd_mp2_process_event(struct amd_i2c_common *i2c_common);
+
+void amd_mp2_rw_timeout(struct amd_i2c_common *i2c_common);
+
+int amd_mp2_register_cb(struct amd_i2c_common *i2c_common);
+int amd_mp2_unregister_cb(struct amd_i2c_common *i2c_common);
+
+struct amd_mp2_dev *amd_mp2_find_device(void);
+
+static inline void amd_mp2_pm_runtime_get(struct amd_mp2_dev *mp2_dev)
+{
+ pm_runtime_get_sync(&mp2_dev->pci_dev->dev);
+}
+
+static inline void amd_mp2_pm_runtime_put(struct amd_mp2_dev *mp2_dev)
+{
+ pm_runtime_mark_last_busy(&mp2_dev->pci_dev->dev);
+ pm_runtime_put_autosuspend(&mp2_dev->pci_dev->dev);
+}
+
+#endif
--
2.17.1