[PATCH 5/6] ARM: dts: s5pv210: aries: Support for more devices present on Aries
From: PaweÅ Chmiel
Date: Fri Dec 28 2018 - 11:18:48 EST
From: Jonathan Bakker <xc-racer2@xxxxxxx>
This commit enables following devices present on Aries based phones:
- pwm-vibrator attached to PWM 1
- poweroff support
- Atmel maXTouch touchscreen. It's connected to i2c2
- Broadcom BCM4329 bluetooth over uart0
Signed-off-by: Jonathan Bakker <xc-racer2@xxxxxxx>
Signed-off-by: PaweÅ Chmiel <pawel.mikolaj.chmiel@xxxxxxxxx>
---
arch/arm/boot/dts/s5pv210-aries.dtsi | 68 ++++++++++++++++++++++++++++
1 file changed, 68 insertions(+)
diff --git a/arch/arm/boot/dts/s5pv210-aries.dtsi b/arch/arm/boot/dts/s5pv210-aries.dtsi
index 35ba009a1a33..b7246f879648 100644
--- a/arch/arm/boot/dts/s5pv210-aries.dtsi
+++ b/arch/arm/boot/dts/s5pv210-aries.dtsi
@@ -41,6 +41,13 @@
};
};
+ vibrator_pwr: regulator-fixed-0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vibrator-en";
+ enable-active-high;
+ gpio = <&gpj1 1 GPIO_ACTIVE_HIGH>;
+ };
+
wifi_pwrseq: wifi-pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&gpg1 2 GPIO_ACTIVE_LOW>;
@@ -314,6 +321,22 @@
reg = <0x36>;
};
};
+
+ vibrator: pwm-vibrator {
+ compatible = "pwm-vibrator";
+ pwms = <&pwm 1 44642 0>;
+ pwm-names = "enable";
+ vcc-supply = <&vibrator_pwr>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm1_out>;
+ };
+
+ poweroff: syscon-poweroff {
+ compatible = "syscon-poweroff";
+ regmap = <&pmu_syscon>;
+ offset = <0x681c>; /* PS_HOLD_CONTROL */
+ value = <0x5200>;
+ };
};
&fimd {
@@ -347,6 +370,23 @@
status = "okay";
};
+&i2c2 {
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <400000>;
+ samsung,i2c-slave-addr = <0x10>;
+ status = "okay";
+
+ touchscreen@4a {
+ compatible = "atmel,maxtouch";
+ reg = <0x4a>;
+ interrupt-parent = <&gpj0>;
+ interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_irq>;
+ reset-gpios = <&gpj1 3 GPIO_ACTIVE_HIGH>;
+ };
+};
+
&mfc {
memory-region = <&mfc_left>, <&mfc_right>;
};
@@ -372,6 +412,13 @@
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
+ bt_host_wake: bt-host-wake {
+ samsung,pins = "gph2-5";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+ samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>;
+ samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+ };
+
tf_detect: tf-detect {
samsung,pins = "gph3-4";
samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
@@ -384,6 +431,17 @@
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
};
+
+ ts_irq: ts-irq {
+ samsung,pins = "gpj0-5";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+ samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+ };
+};
+
+&pwm {
+ samsung,pwm-outputs = <1>;
};
&sdhci1 {
@@ -421,6 +479,16 @@
&uart0 {
status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ max-speed = <115200>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_data &uart0_fctl &bt_host_wake>;
+ shutdown-gpios = <&gpb 3 GPIO_ACTIVE_HIGH>;
+ device-wakeup-gpios = <&gpg3 4 GPIO_ACTIVE_HIGH>;
+ host-wakeup-gpios = <&gph2 5 GPIO_ACTIVE_HIGH>;
+ };
};
&uart1 {
--
2.17.1