[PATCH v5 00/18] MT8183 IOMMU SUPPORT
From: Yong Wu
Date: Mon Dec 31 2018 - 22:57:35 EST
This patchset mainly adds support for mt8183 IOMMU and SMI.
mt8183 has only one M4U like mt8173 and is also MTK IOMMU gen2 which
uses ARM Short-Descriptor translation table format.
The mt8183 M4U-SMI HW diagram is as below:
EMI
|
M4U
|
----------
| |
gals0-rx gals1-rx
| |
| |
gals0-tx gals1-tx
| |
------------
SMI Common
------------
|
+-----+-----+--------+-----+-----+-------+-------+
| | | | | | | |
| | gals-rx gals-rx | gals-rx gals-rx gals-rx
| | | | | | | |
| | | | | | | |
| | gals-tx gals-tx | gals-tx gals-tx gals-tx
| | | | | | | |
larb0 larb1 IPU0 IPU1 larb4 larb5 larb6 CCU
disp vdec img cam venc img cam
All the connections are HW fixed, SW can NOT adjust it.
Compared with mt8173, we add a GALS(Global Async Local Sync) module
between SMI-common and M4U, and additional GALS between larb2/3/5/6
and SMI-common. GALS can help synchronize for the modules in different
clock frequency, it can be seen as a "asynchronous fifo".
GALS can only help transfer the command/data while it doesn't have
the configuring register, thus it has the special "smi" clock and it
doesn't have the "apb" clock. From the diagram above, we add "gals0"
and "gals1" clocks for smi-common and add a "gals" clock for smi-larb.
>From the diagram above, IPU0/IPU1(Image Processor Unit) and CCU(Camera
Control Unit) is connected with smi-common directly, we can take them
as "larb2", "larb3" and "larb7", and their register spaces are
different with the normal larb.
This is the general purpose of each patch in this patchset:
the patch 1..13 add the iommu/smi support for mt8183;
the patch 14..16 add mmu1 support;
the last patches contain some minor changes:
-patch 17 cleanup some smi codes(delete need_larbid).
-patch 18 fix a issue(fix vld_pa_rng).
-patch 19 improve the code flow(add shutdown).
-patch 20 switch to SPDX license.
The dtsi was included at [1] since it should depend on power-domain
and ccf nodes.
[1] http://lists.infradead.org/pipermail/linux-mediatek/2018-December/016539.html
Change notes:
v5: 1) Remove this patch "iommu/mediatek: Constify iommu_ops" for here as it
was applied for v4.21.
2) Again, add 3 preparing patches. Move two property into the plat_data.
iommu/mediatek: Move vld_pa_rng into plat_data
iommu/mediatek: Move reset_axi into plat_data
iommu/mediatek: Refine protect memory definition
3) Change the string "larb_special_mask" to "larb_direct_to_common_mask".
4) Add shutdown callback for mtk_iommu_v1 in patch[19/20].
v4: http://lists.infradead.org/pipermail/linux-mediatek/2018-December/016205.html
1) Add 3 preparing patches. Seperate some minor meaningful code into
a new patch according to Matthias's suggestion.
memory: mtk-smi: Add gals support
iommu/mediatek: Add larb-id remapped support
iommu/mediatek: Add bclk can be supported optionally
2) rebase on "iommu/mediatek: Make it explicitly non-modular"
which was applied.
https://lore.kernel.org/patchwork/patch/1020125/
3) add some comment about "mediatek,larb-id" in the commit message of
the patch "mtk-smi: Get rid of need_larbid".
4) Fix bus_sel value.
v3: https://lists.linuxfoundation.org/pipermail/iommu/2018-November/031121.html
1) rebase on v4.20-rc1.
2) In the dt-binding, add a minor string "mt7623" which also use gen1
since Matthias added it in v4.20.
3) About v7s:
a) for paddr_to_pte, change the param from "arm_v7s_io_pgtable" to
"arm_pgtable_cfg", according to Robin suggestion.
b) Don't use CONFIG_PHYS_ADDR_T_64BIT.
c) add a little comment(pgtable address still don't over 4GB) in the
commit message of the patch "Extend MediaTek 4GB Mode".
4) add "iommu/mediatek: Constify iommu_ops" into this patchset. this may
be helpful for review and merge.
https://lists.linuxfoundation.org/pipermail/iommu/2018-October/030637.html
v2: https://lists.linuxfoundation.org/pipermail/iommu/2018-September/030164.html
1) Fix typo in the commit message of dt-binding.
2) Change larb2/larb3 to the special larbs.
3) Refactor the larb-id remapped array(larbid_remapped), then we
don't need add the new function(mtk_iommu_get_larbid).
4) Add a new patch for v7s two helpers(paddr_to_iopte and
iopte_to_paddr).
5) Change some comment for MTK 4GB mode.
v1: base on v4.19-rc1.
http://lists.infradead.org/pipermail/linux-mediatek/2018-September/014881.html
Yong Wu (20):
dt-bindings: mediatek: Add binding for mt8183 IOMMU and SMI
iommu/mediatek: Use a struct as the platform data
memory: mtk-smi: Use a general config_port interface
memory: mtk-smi: Use a struct for the platform data for smi-common
iommu/io-pgtable-arm-v7s: Add paddr_to_iopte and iopte_to_paddr
helpers
iommu/io-pgtable-arm-v7s: Extend MediaTek 4GB Mode
iommu/mediatek: Add bclk can be supported optionally
iommu/mediatek: Add larb-id remapped support
iommu/mediatek: Refine protect memory definition
iommu/mediatek: Move reset_axi into plat_data
iommu/mediatek: Move vld_pa_rng into plat_data
memory: mtk-smi: Add gals support
iommu/mediatek: Add mt8183 IOMMU support
iommu/mediatek: Add mmu1 support
memory: mtk-smi: Invoke pm runtime_callback to enable clocks
memory: mtk-smi: Add bus_sel for mt8183
memory: mtk-smi: Get rid of need_larbid
iommu/mediatek: Fix VLD_PA_RANGE register backup when suspend
iommu/mediatek: Add shutdown callback
iommu/mediatek: Switch to SPDX license identifier
.../devicetree/bindings/iommu/mediatek,iommu.txt | 15 +-
.../memory-controllers/mediatek,smi-common.txt | 11 +-
.../memory-controllers/mediatek,smi-larb.txt | 3 +
drivers/iommu/io-pgtable-arm-v7s.c | 72 ++++--
drivers/iommu/io-pgtable.h | 7 +-
drivers/iommu/mtk_iommu.c | 145 ++++++-----
drivers/iommu/mtk_iommu.h | 25 +-
drivers/iommu/mtk_iommu_v1.c | 16 +-
drivers/memory/mtk-smi.c | 270 ++++++++++++++-------
include/dt-bindings/memory/mt2701-larb-port.h | 10 +-
include/dt-bindings/memory/mt8173-larb-port.h | 10 +-
include/dt-bindings/memory/mt8183-larb-port.h | 130 ++++++++++
include/soc/mediatek/smi.h | 10 +-
13 files changed, 505 insertions(+), 219 deletions(-)
create mode 100644 include/dt-bindings/memory/mt8183-larb-port.h
--
1.9.1