Re: [PATCH 0/8] Add IPROC I2C slave mode and NIC I2C support

[Ray Jui]

Okay. Just noticed another thing. May I ask if you ran the
'get_maintaimner.pl' script to figure out the 'To:' and 'Cc:'?

I don't see Wolfram's name on on the To or Cc field of the emails you
send out:

Wolfram Sang <wsa@xxxxxxxxxxxxx>

6845 I2C SUBSYSTEM
6846 M:      Wolfram Sang <wsa@xxxxxxxxxxxxx>
6847 L:      linux-i2c@xxxxxxxxxxxxxxx


Thanks,

Ray

On 1/8/2019 6:15 PM, Rayagonda Kokatanur wrote:
> Sorry for confusion. I made mistake in adding bcm-kernel-feedback-list
> while sending patch. Hence sent same patch set with updated email list.Â
> 
> Best regards,
> Rayagonda
> 
> 
> 
> On Jan 8, 2019 10:55 PM, "Ray Jui" <ray.jui@xxxxxxxxxxxx
> <mailto:ray.jui@xxxxxxxxxxxx>> wrote:
> 
>     You sent out the same patch series 3 times without any explanation. Very
>     confusing.
> 
>     Is this the latest one that should be reviewed?
> 
>     Thanks,
> 
>     Ray
> 
> 
>     On 1/8/2019 1:16 AM, Rayagonda Kokatanur wrote:
>     > Hi,
>     > This patchset contains support for IPROC I2C slave and NIC I2C
>     support.
>     > Following are the brief changes done inorder to support both IPROC I2C
>     > slave mode and NIC I2C,
>     >
>     > a. Add support to allow I2C rx transfer upto 255 bytes
>     > b. Add polling mode support to the iProc I2C driver. Polling mode
>     is used
>     >Â Â in certain SoCs where interrupt is not connected from the I2C
>     block.
>     > c. Add warpper read/write access for register to support indirect
>     register
>     >Â Â access. This is required in certain SoCs with this iProc I2C
>     >Â Â block registered.
>     >
>     >
>     > Ray Jui (1):
>     >Â Âdt-bindings: i2c: iproc: make 'interrupts' optional
>     >
>     > Rayagonda Kokatanur (5):
>     >Â Âi2c: iproc: add polling support
>     >Â Âi2c: iproc: use wrapper for read/write access
>     >Â Âdt-bindings: i2c: iproc: add "brcm,iproc-nic-i2c" compatible string
>     >Â Âi2c: iproc: add NIC I2C support
>     >Â Âarm64: dts: Stingray: Add NIC i2c device node
>     >
>     > Shreesha Rajashekar (2):
>     >Â Âi2c: iproc: I2C read up to 255 bytes support
>     >Â Âi2c: iproc: Add Slave mode support
>     >
>     > .../devicetree/bindings/i2c/brcm,iproc-i2c.txt  Â| 14 +-
>     >Â .../arm64/boot/dts/broadcom/stingray/stingray.dtsi |Â 18 +
>     > drivers/i2c/busses/Kconfig            Â| Â1 +
>     > drivers/i2c/busses/i2c-bcm-iproc.c        Â| 767
>     +++++++++++++++++----
>     >Â 4 files changed, 669 insertions(+), 131 deletions(-)
>     >
> 
>