Re: [PATCH v5 3/3] staging: greybus: arche-platform: Switch to the gpio descriptor interface

[Nishad Kamdar]

On Fri, Jan 11, 2019 at 09:48:21AM +0100, Johan Hovold wrote:
> On Thu, Jan 10, 2019 at 11:23:07PM +0530, Nishad Kamdar wrote:
> > Use the gpiod interface instead of the deprecated old non-descriptor
> > interface while continuing to ignore gpio flags from device tree in
> > "svc_reset_onoff()" for now.
> > 
> > Signed-off-by: Nishad Kamdar <nishadkamdar@xxxxxxxxx>
> > ---
> > Changes in v5:
> >   - Change the commit message.
> >   - Restore the names of the gpio device-tree properties without
> >     the "-gpio" suffix.
> > Changes in v4:
> >  - Move 'gpio_desc *svc_sysboot' below the reset flag
> >    as it is more logical to have reset flag below
> >    reset gpio.
> >  - Remove a few unnecessary line breaks.
> > Changes in v3:
> >  - Add this patch to a patchset.
> > Changes in v2:
> >  - Move comment to the same line as to what it applies to.
> > ---
> 
> Also looks good. Some really minor comments to a couple of the error
> messages. The issues are there in the current code, but since you modify
> these messages anyway you might as well fix them up. Please fix that and
> resend with my
> 
> Reviewed-by: Johan Hovold <johan@xxxxxxxxxx>
> 
Ok, I'll do that.

> Really good job with this!
> 
Thank you.
> > @@ -435,6 +428,7 @@ static int arche_platform_probe(struct platform_device *pdev)
> >  	struct device *dev = &pdev->dev;
> >  	struct device_node *np = dev->of_node;
> >  	int ret;
> > +	unsigned int flags;
> >  
> >  	arche_pdata = devm_kzalloc(&pdev->dev, sizeof(*arche_pdata),
> >  				   GFP_KERNEL);
> > @@ -444,61 +438,33 @@ static int arche_platform_probe(struct platform_device *pdev)
> >  	/* setup svc reset gpio */
> >  	arche_pdata->is_reset_act_hi = of_property_read_bool(np,
> >  							     "svc,reset-active-high");
> > -	arche_pdata->svc_reset_gpio = of_get_named_gpio(np,
> > -							"svc,reset-gpio",
> > -							0);
> > -	if (!gpio_is_valid(arche_pdata->svc_reset_gpio)) {
> > -		dev_err(dev, "failed to get reset-gpio\n");
> > -		return arche_pdata->svc_reset_gpio;
> > -	}
> > -	ret = devm_gpio_request(dev, arche_pdata->svc_reset_gpio, "svc-reset");
> > -	if (ret) {
> > -		dev_err(dev, "failed to request svc-reset gpio:%d\n", ret);
> > -		return ret;
> > -	}
> > -	ret = gpio_direction_output(arche_pdata->svc_reset_gpio,
> > -				    arche_pdata->is_reset_act_hi);
> > -	if (ret) {
> > -		dev_err(dev, "failed to set svc-reset gpio dir:%d\n", ret);
> > +	if (arche_pdata->is_reset_act_hi)
> > +		flags = GPIOD_OUT_HIGH;
> > +	else
> > +		flags = GPIOD_OUT_LOW;
> > +
> > +	arche_pdata->svc_reset = devm_gpiod_get(dev, "svc,reset", flags);
> > +	if (IS_ERR(arche_pdata->svc_reset)) {
> > +		ret = PTR_ERR(arche_pdata->svc_reset);
> > +		dev_err(dev, "failed to request svc-reset GPIO:%d\n", ret);
> 
> Add a space after ':' for consistency.
> 
Ok. I'll do that.
> > @@ -515,19 +481,11 @@ static int arche_platform_probe(struct platform_device *pdev)
> >  	arche_pdata->num_apbs = of_get_child_count(np);
> >  	dev_dbg(dev, "Number of APB's available - %d\n", arche_pdata->num_apbs);
> >  
> > -	arche_pdata->wake_detect_gpio = of_get_named_gpio(np,
> > -							  "svc,wake-detect-gpio",
> > -							  0);
> > -	if (arche_pdata->wake_detect_gpio < 0) {
> > -		dev_err(dev, "failed to get wake detect gpio\n");
> > -		return arche_pdata->wake_detect_gpio;
> > -	}
> > -
> > -	ret = devm_gpio_request(dev, arche_pdata->wake_detect_gpio,
> > -				"wake detect");
> > -	if (ret) {
> > -		dev_err(dev, "Failed requesting wake_detect gpio %d\n",
> > -			arche_pdata->wake_detect_gpio);
> > +	arche_pdata->wake_detect = devm_gpiod_get(dev, "svc,wake-detect",
> > +						  GPIOD_IN);
> > +	if (IS_ERR(arche_pdata->wake_detect)) {
> > +		ret = PTR_ERR(arche_pdata->wake_detect);
> > +		dev_err(dev, "Failed requesting wake_detect GPIO %d\n", ret);
> 
> Add colon after "GPIO" for consistency (and to avoid ambiguity).
> 

Ok, I'll do that.

Thanks for the review,
Nishad
> >  		return ret;
> >  	}
> 
> Thanks,
> Johan