[PATCH 2/3] dma: imx-sdma: add clock ratio 1:1 check

From: Angus Ainslie (Purism)
Date: Sat Jan 19 2019 - 21:05:45 EST


On i.mx8 mscale B0 chip, AHB/SDMA clock ratio 2:1 can't be supportted,
since SDMA clock ratio has to be increased to 250Mhz, AHB can't reach
to 500Mhz, so use 1:1 instead.

based on NXP commit MLK-16841-1

Signed-off-by: Angus Ainslie (Purism) <angus@xxxxxxxx>
---
.../devicetree/bindings/dma/fsl-imx-sdma.txt | 2 +-
drivers/dma/imx-sdma.c | 20 +++++++++++++++----
2 files changed, 17 insertions(+), 5 deletions(-)

diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
index 3c9a57a8443b..b3fbac401bd0 100644
--- a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
+++ b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
@@ -67,7 +67,7 @@ Optional properties:
reg is the GPR register offset.
shift is the bit position inside the GPR register.
val is the value of the bit (0 or 1).
-
+- fsl,ratio-1-1: AHB/SDMA core clock ration 1:1, 2:1 without this.
Examples:

sdma@83fb0000 {
diff --git a/drivers/dma/imx-sdma.c b/drivers/dma/imx-sdma.c
index 064bc50d1e99..616ffd6b301e 100644
--- a/drivers/dma/imx-sdma.c
+++ b/drivers/dma/imx-sdma.c
@@ -440,6 +440,8 @@ struct sdma_engine {
unsigned int irq;
dma_addr_t bd0_phys;
struct sdma_buffer_descriptor *bd0;
+ /* clock ratio for AHB:SDMA core. 1:1 is 1, 2:1 is 0*/
+ bool clk_ratio;
};

static int sdma_config_write(struct dma_chan *chan,
@@ -662,8 +664,14 @@ static int sdma_run_channel0(struct sdma_engine *sdma)
dev_err(sdma->dev, "Timeout waiting for CH0 ready\n");

/* Set bits of CONFIG register with dynamic context switching */
- if (readl(sdma->regs + SDMA_H_CONFIG) == 0)
- writel_relaxed(SDMA_H_CONFIG_CSM, sdma->regs + SDMA_H_CONFIG);
+ if (readl(sdma->regs + SDMA_H_CONFIG) == 0) {
+ if (sdma->clk_ratio)
+ reg = SDMA_H_CONFIG_CSM | SDMA_H_CONFIG_ACR;
+ else
+ reg = SDMA_H_CONFIG_CSM;
+
+ writel_relaxed(reg, sdma->regs + SDMA_H_CONFIG);
+ }

return ret;
}
@@ -1880,8 +1888,10 @@ static int sdma_init(struct sdma_engine *sdma)
writel_relaxed(0x4050, sdma->regs + SDMA_CHN0ADDR);

/* Set bits of CONFIG register but with static context switching */
- /* FIXME: Check whether to set ACR bit depending on clock ratios */
- writel_relaxed(0, sdma->regs + SDMA_H_CONFIG);
+ if (sdma->clk_ratio)
+ writel_relaxed(SDMA_H_CONFIG_ACR, sdma->regs + SDMA_H_CONFIG);
+ else
+ writel_relaxed(0, sdma->regs + SDMA_H_CONFIG);

writel_relaxed(ccb_phys, sdma->regs + SDMA_H_C0PTR);

@@ -1975,6 +1985,8 @@ static int sdma_probe(struct platform_device *pdev)
if (!sdma)
return -ENOMEM;

+ sdma->clk_ratio = of_property_read_bool(np, "fsl,ratio-1-1");
+
spin_lock_init(&sdma->channel_0_lock);

sdma->dev = &pdev->dev;
--
2.17.1