Re: [PATCH V2 2/4] i2c: tegra: Update I2C transfer using buffer

[Dmitry Osipenko]

25.01.2019 23:20, Sowjanya Komatineni ÐÐÑÐÑ:
> 
> 
>>> This patch prepares the buffer with the message bytes to be 
>>> transmitted along with the packet header information and then performs 
>>> i2c transfer in PIO mode.
>>>
>>> Signed-off-by: Sowjanya Komatineni <skomatineni@xxxxxxxxxx>
>>> ---
>>>  [V2] : DMA support changes include preparing buffer with message bytes and
>>> 	and header before sending them through DMA. So splitted the whole
>>> 	change into 2 seperate patches in this series.
>>>
>>>  drivers/i2c/busses/i2c-tegra.c | 97 
>>> +++++++++++++++++++++++++++++-------------
>>>  1 file changed, 68 insertions(+), 29 deletions(-)
>>>
>>> diff --git a/drivers/i2c/busses/i2c-tegra.c 
>>> b/drivers/i2c/busses/i2c-tegra.c index ef854be4c837..13bce1411ddc 
>>> 100644
>>> --- a/drivers/i2c/busses/i2c-tegra.c
>>> +++ b/drivers/i2c/busses/i2c-tegra.c
>>> @@ -117,6 +117,9 @@
>>>  #define I2C_MST_FIFO_STATUS_TX_MASK		0xff0000
>>>  #define I2C_MST_FIFO_STATUS_TX_SHIFT		16
>>>  
>>> +/* Packet header size in bytes */
>>> +#define I2C_PACKET_HEADER_SIZE			12
>>> +
>>>  /*
>>>   * msg_end_type: The bus control which need to be send at end of transfer.
>>>   * @MSG_END_STOP: Send stop pulse at end of transfer.
>>> @@ -677,35 +680,69 @@ static irqreturn_t tegra_i2c_isr(int irq, void *dev_id)
>>>  	return IRQ_HANDLED;
>>>  }
>>>  
>>> +static int tegra_i2c_start_pio_xfer(struct tegra_i2c_dev *i2c_dev) {
>>> +	u32 *buffer = (u32 *)i2c_dev->msg_buf;
>>> +	unsigned long flags;
>>> +	u32 int_mask;
>>> +
>>> +	spin_lock_irqsave(&i2c_dev->xfer_lock, flags);
>>> +
>>> +	int_mask = I2C_INT_NO_ACK | I2C_INT_ARBITRATION_LOST;
>>> +	tegra_i2c_unmask_irq(i2c_dev, int_mask);
>>> +
>>> +	i2c_writel(i2c_dev, *(buffer++), I2C_TX_FIFO);
>>> +	i2c_writel(i2c_dev, *(buffer++), I2C_TX_FIFO);
>>> +	i2c_writel(i2c_dev, *(buffer++), I2C_TX_FIFO);
>>> +
>>> +	i2c_dev->msg_buf = (u8 *) buffer;
>>> +
>>> +	if (!i2c_dev->msg_read)
>>> +		tegra_i2c_fill_tx_fifo(i2c_dev);
>>> +
>>> +	if (i2c_dev->hw->has_per_pkt_xfer_complete_irq)
>>> +		int_mask |= I2C_INT_PACKET_XFER_COMPLETE;
>>> +	if (i2c_dev->msg_read)
>>> +		int_mask |= I2C_INT_RX_FIFO_DATA_REQ;
>>> +	else if (i2c_dev->msg_buf_remaining)
>>> +		int_mask |= I2C_INT_TX_FIFO_DATA_REQ;
>>> +
>>> +	tegra_i2c_unmask_irq(i2c_dev, int_mask);
>>> +	spin_unlock_irqrestore(&i2c_dev->xfer_lock, flags);
>>> +	dev_dbg(i2c_dev->dev, "unmasked irq: %02x\n",
>>> +		i2c_readl(i2c_dev, I2C_INT_MASK));
>>> +
>>> +	return 0;
>>> +}
>>> +
>>>  static int tegra_i2c_xfer_msg(struct tegra_i2c_dev *i2c_dev,
>>>  	struct i2c_msg *msg, enum msg_end_type end_state)  {
>>>  	u32 packet_header;
>>>  	u32 int_mask;
>>>  	unsigned long time_left;
>>> -	unsigned long flags;
>>> +	u32 *buffer;
>>> +	int ret = 0;
>>> +
>>> +	buffer = kmalloc(ALIGN(msg->len, BYTES_PER_FIFO_WORD) +
>>> +					I2C_PACKET_HEADER_SIZE, GFP_KERNEL);
>>> +	if (!buffer)
>>> +		return -ENOMEM;
>>
>> Isn't it possible to avoid "buffer" allocation / copying overhead and keep code as-is for the PIO mode?
>>
> 
> Keeping PIO mode code as is and adding DMA mode will have redundant code for header generation and msg complete timeout sections.
> Also in existing PIO mode implementation, TX FIFO is filled as soon as the word is ready but for DMA mode need to put all msg bytes along with header together to send thru DMA.
> So created common buffer to perform PIO/DMA to reduce redundancy.
> 

Okay, what about something like in this sketch:

...
	if (msg->flags & I2C_M_RD)
		xfer_size = msg->len;
	else
		xfer_size = ALIGN(msg->len, BYTES_PER_FIFO_WORD) +
			    I2C_PACKET_HEADER_SIZE;

	dma = ((xfer_size > I2C_PIO_MODE_MAX_LEN) &&
		i2c_dev->tx_dma_chan && i2c_dev->rx_dma_chan);

	if (dma) {
		buffer = kmalloc(ALIGN(msg->len, BYTES_PER_FIFO_WORD) +
				I2C_PACKET_HEADER_SIZE, GFP_KERNEL);
		i2c_dev->msg_buf = (u8 *)buffer;
	}

	packet_header = (0 << PACKET_HEADER0_HEADER_SIZE_SHIFT) |
				PACKET_HEADER0_PROTOCOL_I2C |
				(i2c_dev->cont_id << PACKET_HEADER0_CONT_ID_SHIFT) |
				(1 << PACKET_HEADER0_PACKET_ID_SHIFT);
		i2c_writel(i2c_dev, packet_header, I2C_TX_FIFO);

	if (dma)
		(*buffer++) = packet_header;
	else
		i2c_writel(i2c_dev, packet_header, I2C_TX_FIFO);

... and so on.

Likely that kmalloc overhead will be bigger than the above variant. Please consider to avoid kmalloc and copying for the PIO case in the next version.