Re: [PATCH] ARM: socfpga: fix base address of SDR controller

[Simon Goldschmidt]

Am 30.01.2019 um 16:50 schrieb Dinh Nguyen:
> On 1/30/19 12:00 AM, Simon Goldschmidt wrote:
> > + Marek (as I really want to keep the dts in Linux and U-Boot in sync)
> > On Wed, Jan 30, 2019 at 1:16 AM Dinh Nguyen <dinguyen@xxxxxxxxxx> wrote:
> > > On 1/29/19 2:08 PM, Simon Goldschmidt wrote:
> > > > From: Simon Goldschmidt <simon.k.r.goldschmidt@xxxxxxxxx>
> > > >
> > > > The documentation for socfpga gen5 says the base address of the sdram
> > > > controller is 0xffc20000, while the current devicetree says it is at
> > > > 0xffc25000.
> > > >
> > > > While this is not a problem for Linux, as it only accesses the registers
> > > > above 0xffc25000, it *is* a problem for U-Boot because the lower registers
> > > > are used during DDR calibration (up to now, the U-Boot driver does not use
> > > > the dts address, but that should change).
> > > >
> > > > To keep Linux and U-Boot devicetrees in sync, this patch changes the base
> > > > address to 0xffc20000 and adapts the 2 files where it is currently used.
> > > >
> > > > This patch changes the dts and 2 drivers with one commit to prevent
> > > > breaking the code if dts change and driver change would be split.
> > > >
> > > > Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@xxxxxxxxx>
> > > > ---
> > > >
> > > >   arch/arm/boot/dts/socfpga.dtsi       | 4 ++--
> > > >   arch/arm/mach-socfpga/self-refresh.S | 4 ++--
> > > >   drivers/fpga/altera-fpga2sdram.c     | 2 +-
> > > >   3 files changed, 5 insertions(+), 5 deletions(-)
> > > >
> > > > diff --git a/arch/arm/boot/dts/socfpga.dtsi b/arch/arm/boot/dts/socfpga.dtsi
> > > > index f365003f0..8f6c1a5d6 100644
> > > > --- a/arch/arm/boot/dts/socfpga.dtsi
> > > > +++ b/arch/arm/boot/dts/socfpga.dtsi
> > > > @@ -788,9 +788,9 @@
> > > >                        reg = <0xfffec000 0x100>;
> > > >                };
> > > >
> > > > -             sdr: sdr@ffc25000 {
> > > > +             sdr: sdr@ffc20000 {
> > > >                        compatible = "altr,sdr-ctl", "syscon";
> > > > -                     reg = <0xffc25000 0x1000>;
> > > > +                     reg = <0xffc20000 0x6000>;
> > >
> > > I don't see the U-Boot device tree having this change. Yes, the
> > > documentation does state that the SDR address starts at 0xffc20000, but
> > > all of the pertinent registers start at 0x5000 offset. Thus, the
> > > starting address should be 0xffc25000.[1]
> >
> > You don't see it in U-Boot as I'm working on a patch for that.
> > As I wrote in the commit message, U-Boot currently does not use the
> > devicetree for the SDR driver, but I want to convert it to do that.
>
> That's great! Can you elaborate on what is the impetus for converting
> the SDR driver to use the dts?

The initial reason to do so was to move its reset handling from U-Boot 
SPL to the driver itself. Moving from ad-hoc code to using the reset driver.

And when it's being converted to using the reset handle from dts, I 
think it should also use the base address from dts.

Regards,
Simon