Re: [PATCH 8/9] dt-bindings: spi: atmel-quadspi: QuadSPI driver for Microchip SAM9X60

[Tudor.Ambarus]

On 01/30/2019 07:30 PM, Boris Brezillon wrote:
> On Wed, 30 Jan 2019 15:08:45 +0000
> <Tudor.Ambarus@xxxxxxxxxxxxx> wrote:
> 
>> From: Tudor Ambarus <tudor.ambarus@xxxxxxxxxxxxx>
>>
>> The sam9x60 qspi controller uses 2 clocks, one for the peripheral register
>> access, the other for the qspi core and phy. Both are mandatory.
>>
>> Signed-off-by: Tudor Ambarus <tudor.ambarus@xxxxxxxxxxxxx>
>> ---
>>  .../devicetree/bindings/spi/atmel-quadspi.txt      | 28 ++++++++++++++++++++--
>>  1 file changed, 26 insertions(+), 2 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/spi/atmel-quadspi.txt b/Documentation/devicetree/bindings/spi/atmel-quadspi.txt
>> index e9dae6264d89..e7b7f297c5d7 100644
>> --- a/Documentation/devicetree/bindings/spi/atmel-quadspi.txt
>> +++ b/Documentation/devicetree/bindings/spi/atmel-quadspi.txt
>> @@ -1,14 +1,22 @@
>>  * Atmel Quad Serial Peripheral Interface (QSPI)
>>  
>>  Required properties:
>> -- compatible:     Should be "atmel,sama5d2-qspi".
>> +- compatible:     Should be one of the following
>> +		  - "atmel,sama5d2-qspi"
>> +		  - "microchip,sam9x60-qspi"
>>  - reg:            Should contain the locations and lengths of the base registers
>>                    and the mapped memory.
>>  - reg-names:      Should contain the resource reg names:
>>                    - qspi_base: configuration register address space
>>                    - qspi_mmap: memory mapped address space
>>  - interrupts:     Should contain the interrupt for the device.
>> -- clocks:         The phandle of the clock needed by the QSPI controller.
>> +- clocks:	  - "atmel,sama5d2-qspi": the phandle of the clock needed by the
>> +		  QSPI controller.
>> +		  - "microchip,sam9x60-qspi": should reference the peripheral
>> +		  and system QSPI clocks.
>> +- clock-names:    Only for sam9x60 - should contain two strigs:
> 
> 							   ^strings
> 
> And I think naming clocks even for sama5d2 is a good practice, so I'd
> suggest making "pclk" mandatory even if you support unnamed clk in the
> driver to be backward compatible with old DTs.

agreed

> 
>> +		  - "pclk" for the peripheral clock
>> +		  - "qspick" for the system clock
>>  - #address-cells: Should be <1>.
>>  - #size-cells:    Should be <0>.
>>  
>> @@ -29,3 +37,19 @@ spi@f0020000 {
>>  		...
>>  	};
>>  };
>> +
>> +qspi@f0014000 {
>> +	compatible = "microchip,sam9x60-qspi";
>> +	reg = <0xf0014000 0x100>, <0x70000000 0x08000000>;
>> +	reg-names = "qspi_base", "qspi_mmap";
>> +	interrupts = <35 IRQ_TYPE_LEVEL_HIGH 7>;
>> +	clocks =  <&pmc PMC_TYPE_PERIPHERAL 35>, <&pmc PMC_TYPE_SYSTEM 19>;
>> +	clock-names = "pclk", "qspick";
>> +	#address-cells = <1>;
>> +	#size-cells = <0>;
>> +	pinctrl-names = "default";
>> +
>> +	flash@0 {
>> +		...
>> +	};
>> +};
> 
> No need to add one example per compat, especially when all that
> changes is the compat string and an extra clk. 

ok, thanks!
ta