Re: [PATCH v3 5/5] Revert "scsi: ufs: disable vccq if it's not needed by UFS device"

From: Bjorn Andersson
Date: Tue Feb 05 2019 - 14:46:14 EST


On Tue 05 Feb 02:52 PST 2019, Alim Akhtar wrote:

> Hi Bjorn,
>
> On 05/02/19 11:57 AM, Bjorn Andersson wrote:
> > On Mon 04 Feb 20:58 PST 2019, Alim Akhtar wrote:
> >
> >> Hi Marc,
> >>
> >> On 04/02/19 11:12 PM, Marc Gonzalez wrote:
> >>> This reverts commit 60f0187031c05e04cbadffb62f557d0ff3564490.
> >>>
> >>> Calling ufshcd_set_vccq_rail_unused hangs my system.
> >>> It seems vccq is not *not* needed.
> >>>
> >>> Signed-off-by: Marc Gonzalez <marc.w.gonzalez@xxxxxxx>
> >>> ---
> >>
> >> AFAIK Samsung and Toshiba UFS devices does not use VCCQ (this pin is
> >> either floating or connected to Ground, at least on the devices that I
> >> have worked on).
> >
> > But why does such system define a vccq-supply? If the system doesn't
> > have a regulator connected to VCCQ, then the UFS driver shouldn't be
> > told that there is one. And if VCCQ is optional the UFS driver should
> > support the fact that this regulator might not be supplied (i.e. call
> > regulator_get_optional() and handle the error indicating that the supply
> > isn't specified).
> >
> As per JESD220C, chapter 6.1, it does says "VCCQ - Supply voltage used
> typically for the memory controller and optionally for the PHY
> interface, the memory IO, and any other internal very low voltage block"
> And we have VCCQ2 - which serve the pretty much same purpose. The
> voltage range for VCCQ and VCCQ2 are different, VCCQ has a lower voltage
> suitable to some low voltage block inside UFS device. I think this is
> design consideration which allow some vendor to use one less physical
> pin may be. And also depends on the voltage requirements of some of the
> internal circuit.
>

This looks to me that you are required to have a VCCQ. But you said that
you do not have a regulator supplying VCCQ on your board, and if that
really is the case then you should not specify vccq-supply.

The patch Marc is reverting states that for devices that does not have
VCCQ connected, some unrelated regulator should be assigned to the UFS
driver so that it can turn it off.


If you have a regulator connected to VCCQ then it should go in
vccq-supply, if you have a regulator connected to VCCQ2 the is should go
in vccq2-supply. If you don't have these pins connected then there
shouldn't be any regulators specified here!

Regards,
Bjorn

>
> > Regards,
> > Bjorn
> >
> >> You said your system hanged, I believe you have set UFS_DEVICE_NO_VCCQ
> >> quirks, in that case VCCQ regulator should having been disabled.
> >> So you mean your system hanged because vccq regulator got disabled?
> >>
> >>> drivers/scsi/ufs/ufs.h | 1 -
> >>> drivers/scsi/ufs/ufshcd.c | 59 +++------------------------------------
> >>> 2 files changed, 4 insertions(+), 56 deletions(-)
> >>>
> >>> diff --git a/drivers/scsi/ufs/ufs.h b/drivers/scsi/ufs/ufs.h
> >>> index dd65fea07687..7da7318eb6a6 100644
> >>> --- a/drivers/scsi/ufs/ufs.h
> >>> +++ b/drivers/scsi/ufs/ufs.h
> >>> @@ -514,7 +514,6 @@ struct ufs_vreg {
> >>> struct regulator *reg;
> >>> const char *name;
> >>> bool enabled;
> >>> - bool unused;
> >>> int min_uV;
> >>> int max_uV;
> >>> int min_uA;
> >>> diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
> >>> index 9ba7671b84f8..8b9a01073d62 100644
> >>> --- a/drivers/scsi/ufs/ufshcd.c
> >>> +++ b/drivers/scsi/ufs/ufshcd.c
> >>> @@ -245,7 +245,6 @@ static int ufshcd_probe_hba(struct ufs_hba *hba);
> >>> static int __ufshcd_setup_clocks(struct ufs_hba *hba, bool on,
> >>> bool skip_ref_clk);
> >>> static int ufshcd_setup_clocks(struct ufs_hba *hba, bool on);
> >>> -static int ufshcd_set_vccq_rail_unused(struct ufs_hba *hba, bool unused);
> >>> static int ufshcd_uic_hibern8_exit(struct ufs_hba *hba);
> >>> static int ufshcd_uic_hibern8_enter(struct ufs_hba *hba);
> >>> static inline void ufshcd_add_delay_before_dme_cmd(struct ufs_hba *hba);
> >>> @@ -6819,11 +6818,6 @@ static int ufshcd_probe_hba(struct ufs_hba *hba)
> >>> ufs_fixup_device_setup(hba, &card);
> >>> ufshcd_tune_unipro_params(hba);
> >>>
> >>> - ret = ufshcd_set_vccq_rail_unused(hba,
> >>> - (hba->dev_quirks & UFS_DEVICE_NO_VCCQ) ? true : false);
> >>> - if (ret)
> >>> - goto out;
> >>> -
> >>> /* UFS device is also active now */
> >>> ufshcd_set_ufs_dev_active(hba);
> >>> ufshcd_force_reset_auto_bkops(hba);
> >>> @@ -7007,24 +7001,13 @@ static int ufshcd_config_vreg_load(struct device *dev, struct ufs_vreg *vreg,
> >>> static inline int ufshcd_config_vreg_lpm(struct ufs_hba *hba,
> >>> struct ufs_vreg *vreg)
> >>> {
> >>> - if (!vreg)
> >>> - return 0;
> >>> - else if (vreg->unused)
> >>> - return 0;
> >>> - else
> >>> - return ufshcd_config_vreg_load(hba->dev, vreg,
> >>> - UFS_VREG_LPM_LOAD_UA);
> >>> + return ufshcd_config_vreg_load(hba->dev, vreg, UFS_VREG_LPM_LOAD_UA);
> >>> }
> >>>
> >>> static inline int ufshcd_config_vreg_hpm(struct ufs_hba *hba,
> >>> struct ufs_vreg *vreg)
> >>> {
> >>> - if (!vreg)
> >>> - return 0;
> >>> - else if (vreg->unused)
> >>> - return 0;
> >>> - else
> >>> - return ufshcd_config_vreg_load(hba->dev, vreg, vreg->max_uA);
> >>> + return ufshcd_config_vreg_load(hba->dev, vreg, vreg->max_uA);
> >>> }
> >>>
> >>> static int ufshcd_config_vreg(struct device *dev,
> >>> @@ -7062,9 +7045,7 @@ static int ufshcd_enable_vreg(struct device *dev, struct ufs_vreg *vreg)
> >>> {
> >>> int ret = 0;
> >>>
> >>> - if (!vreg)
> >>> - goto out;
> >>> - else if (vreg->enabled || vreg->unused)
> >>> + if (!vreg || vreg->enabled)
> >>> goto out;
> >>>
> >>> ret = ufshcd_config_vreg(dev, vreg, true);
> >>> @@ -7084,9 +7065,7 @@ static int ufshcd_disable_vreg(struct device *dev, struct ufs_vreg *vreg)
> >>> {
> >>> int ret = 0;
> >>>
> >>> - if (!vreg)
> >>> - goto out;
> >>> - else if (!vreg->enabled || vreg->unused)
> >>> + if (!vreg || !vreg->enabled)
> >>> goto out;
> >>>
> >>> ret = regulator_disable(vreg->reg);
> >>> @@ -7192,36 +7171,6 @@ static int ufshcd_init_hba_vreg(struct ufs_hba *hba)
> >>> return 0;
> >>> }
> >>>
> >>> -static int ufshcd_set_vccq_rail_unused(struct ufs_hba *hba, bool unused)
> >>> -{
> >>> - int ret = 0;
> >>> - struct ufs_vreg_info *info = &hba->vreg_info;
> >>> -
> >>> - if (!info)
> >>> - goto out;
> >>> - else if (!info->vccq)
> >>> - goto out;
> >>> -
> >>> - if (unused) {
> >>> - /* shut off the rail here */
> >>> - ret = ufshcd_toggle_vreg(hba->dev, info->vccq, false);
> >>> - /*
> >>> - * Mark this rail as no longer used, so it doesn't get enabled
> >>> - * later by mistake
> >>> - */
> >>> - if (!ret)
> >>> - info->vccq->unused = true;
> >>> - } else {
> >>> - /*
> >>> - * rail should have been already enabled hence just make sure
> >>> - * that unused flag is cleared.
> >>> - */
> >>> - info->vccq->unused = false;
> >>> - }
> >>> -out:
> >>> - return ret;
> >>> -}
> >>> -
> >>> static int __ufshcd_setup_clocks(struct ufs_hba *hba, bool on,
> >>> bool skip_ref_clk)
> >>> {
> >>>
> >
> >