Re: [PATCH v7 3/6] dt-bindings: pinctrl: mt8183: add binding document

From: Rob Herring
Date: Mon Feb 18 2019 - 10:48:29 EST


On Fri, Feb 15, 2019 at 10:35:39AM +0100, Matthias Brugger wrote:
>
>
> On 15/02/2019 07:02, Erin Lo wrote:
> > From: Zhiyong Tao <zhiyong.tao@xxxxxxxxxxxx>
> >
> > The commit adds mt8183 compatible node in binding document.
> >
> > Signed-off-by: Zhiyong Tao <zhiyong.tao@xxxxxxxxxxxx>
> > Signed-off-by: Erin Lo <erin.lo@xxxxxxxxxxxx>
> > ---
> > .../devicetree/bindings/pinctrl/pinctrl-mt8183.txt | 115 +++++++++++++++++++++
> > 1 file changed, 115 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/pinctrl/pinctrl-mt8183.txt
> >
> > diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8183.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8183.txt
> > new file mode 100644
> > index 0000000..364e673
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8183.txt
> > @@ -0,0 +1,115 @@
> > +* Mediatek MT8183 Pin Controller
> > +
> > +The Mediatek's Pin controller is used to control SoC pins.
> > +
> > +Required properties:
> > +- compatible: value should be one of the following.
> > + "mediatek,mt8183-pinctrl", compatible with mt8183 pinctrl.
> > +- gpio-controller : Marks the device node as a gpio controller.
> > +- #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO
> > + binding is used, the amount of cells must be specified as 2. See the below
> > + mentioned gpio binding representation for description of particular cells.
> > +- gpio-ranges : gpio valid number range.
> > +- reg: physicall address base for gpio base registers. There are nine
>
> s/physicall/physical
>
> > + physicall address base in mt8183. They are 0x10005000, 0x11F20000,
> > + 0x11E80000, 0x11E70000, 0x11E90000, 0x11D30000, 0x11D20000, 0x11C50000,
> > + 0x11F30000.
> > +
> > + Eg: <&pio 6 0>
> > + <[phandle of the gpio controller node]
> > + [line number within the gpio controller]
> > + [flags]>
> > +
> > + Values for gpio specifier:
> > + - Line number: is a value between 0 to 202.
> > + - Flags: bit field of flags, as defined in <dt-bindings/gpio/gpio.h>.
> > + Only the following flags are supported:
> > + 0 - GPIO_ACTIVE_HIGH
> > + 1 - GPIO_ACTIVE_LOW
> > +
> > +Optional properties:
> > +- reg-names: gpio base register names. There are nine gpio base register
> > + names in mt8183. They are "iocfg0", "iocfg1", "iocfg2", "iocfg3", "iocfg4",
> > + "iocfg5", "iocfg6", "iocfg7", "iocfg8".
> > +- interrupt-controller: Marks the device node as an interrupt controller
> > +- #interrupt-cells: Should be two.
> > +- interrupts : The interrupt outputs from the controller.
>
> we are missing interrupt-parent here.

No, because interrupt-parent is implied and may be in a parent node.

What's missing is how many interrupts and what are they?

Rob