Re: [RFC PATCH] docs/memory-barriers.txt: Rewrite "KERNEL I/O BARRIER EFFECTS" section

[Will Deacon]

On Tue, Feb 19, 2019 at 02:01:50PM +0100, Arnd Bergmann wrote:
> On Tue, Feb 19, 2019 at 12:36 PM Will Deacon <will.deacon@xxxxxxx> wrote:
> > On Tue, Feb 19, 2019 at 12:31:50PM +0100, Arnd Bergmann wrote:
> > > On Tue, Feb 19, 2019 at 11:27 AM Thomas Petazzoni
> > > <thomas.petazzoni@xxxxxxxxxxx> wrote:
> > >
> > > I think an example of this would be a driver using outb() to disable
> > > an interrupt, and then relying on the the interrupt no longer happening
> > > after the outb().
> >
> > Isn't that racy already? i.e. the interrupt could fire just before you
> > disabled it, but not get delivered by the irq controller until after you'd
> > disabled it at the device?
> 
> Probably, I had a hard enough time trying to come up with any example ;-)

You and me both!

> One reference to non-posted transaction in a comment is in
> drivers/net/ethernet/dec/tulip/de4x5.c:
> 
> /*
> ** The DE4X5 interrupt handler.
> **
> ** I/O Read/Writes through intermediate PCI bridges are never 'posted',
> ** so that the asserted interrupt always has some real data to work with -
> ** if these I/O accesses are ever changed to memory accesses, ensure the
> ** STS write is read immediately to complete the transaction if the adapter
> ** is not on bus 0. Lost interrupts can still occur when the PCI bus load
> ** is high and descriptor status bits cannot be set before the associated
> ** interrupt is asserted and this routine entered.
> */

Thankfully, that driver is both old and non-portable:

  depends on VIRT_TO_BUS || ALPHA || PPC || SPARC

so I'm not especially concerned about it. Judging by the comment, we'd
need to add something like:


diff --git a/drivers/net/ethernet/dec/tulip/de4x5.c b/drivers/net/ethernet/dec/tulip/de4x5.c
index 66535d1653f6..c85089f65b0e 100644
--- a/drivers/net/ethernet/dec/tulip/de4x5.c
+++ b/drivers/net/ethernet/dec/tulip/de4x5.c
@@ -1556,6 +1556,10 @@ de4x5_interrupt(int irq, void *dev_id)
 	sts = inl(DE4X5_STS);            /* Read IRQ status */
 	outl(sts, DE4X5_STS);            /* Reset the board interrupts */
 
+	/* Beware of PCI posted writes */
+	if (IS_ENABLED(CONFIG_ARM64) && lp->bus_num)
+		inl(DE4X5_STS);
+
 	if (!(sts & lp->irq_mask)) break;/* All done */
 	handled = 1;
 


if we wanted to get this working reliably on arm64. However, I'll be honest
and say we haven't had much demand for supporting DEC PCI devices yet :)

> I found another comment in the via-rhine driver:
> 
> /* Beware of PCI posted writes */
> #define IOSYNC  do { ioread8(ioaddr + StationAddr); } while (0)
> 
> this one is used in the chip reset function, and in the transmit
> path.

Since this is doing a read-back, I take this comment as saying "posted
writes are a thing, so perform a read-back to force the prior write to
complete", which is fine.

Will