[PATCH V2 2/8] net: ethernet: stmmac: update to support all PHY config for stm32mp157c.
From: Christophe Roullier
Date: Fri Feb 22 2019 - 03:29:17 EST
Update glue codes to support all PHY config on stm32mp157c
PHY_MODE (MII,GMII, RMII, RGMII) and in normal, PHY wo crystal (25Mhz),
PHY wo crystal (50Mhz), No 125Mhz from PHY config.
Signed-off-by: Christophe Roullier <christophe.roullier@xxxxxx>
---
drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c | 105 +++++++++++++++++-----
1 file changed, 85 insertions(+), 20 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
index d1cf145..8d5150a 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
@@ -25,9 +25,24 @@
#define SYSCFG_MCU_ETH_MASK BIT(23)
#define SYSCFG_MP1_ETH_MASK GENMASK(23, 16)
+#define SYSCFG_PMCCLRR_OFFSET 0x40
#define SYSCFG_PMCR_ETH_CLK_SEL BIT(16)
#define SYSCFG_PMCR_ETH_REF_CLK_SEL BIT(17)
+
+/* Ethernet PHY interface selection in register SYSCFG Configuration
+ *------------------------------------------
+ * src |BIT(23)| BIT(22)| BIT(21)|BIT(20)|
+ *------------------------------------------
+ * MII | 0 | 0 | 0 | 1 |
+ *------------------------------------------
+ * GMII | 0 | 0 | 0 | 0 |
+ *------------------------------------------
+ * RGMII | 0 | 0 | 1 | n/a |
+ *------------------------------------------
+ * RMII | 1 | 0 | 0 | n/a |
+ *------------------------------------------
+ */
#define SYSCFG_PMCR_ETH_SEL_MII BIT(20)
#define SYSCFG_PMCR_ETH_SEL_RGMII BIT(21)
#define SYSCFG_PMCR_ETH_SEL_RMII BIT(23)
@@ -35,15 +50,54 @@
#define SYSCFG_MCU_ETH_SEL_MII 0
#define SYSCFG_MCU_ETH_SEL_RMII 1
+/* STM32MP1 register definitions
+ *
+ * Below table summarizes the clock requirement and clock sources for
+ * supported phy interface modes.
+ * __________________________________________________________________________
+ *|PHY_MODE | Normal | PHY wo crystal| PHY wo crystal |No 125Mhz from PHY|
+ *| | | 25MHz | 50MHz | |
+ * ---------------------------------------------------------------------------
+ *| MII | - | eth-ck | n/a | n/a |
+ *| | | | | |
+ * ---------------------------------------------------------------------------
+ *| GMII | - | eth-ck | n/a | n/a |
+ *| | | | | |
+ * ---------------------------------------------------------------------------
+ *| RGMII | - | eth-ck | n/a | eth-ck (no pin) |
+ *| | | | | st,eth_clk_sel |
+ * ---------------------------------------------------------------------------
+ *| RMII | - | eth-ck | eth-ck | n/a |
+ *| | | | st,eth_ref_clk_sel | |
+ * ---------------------------------------------------------------------------
+ *
+ * BIT(17) : set this bit in RMII mode when you have PHY without crystal 50MHz
+ * BIT(16) : set this bit in GMII/RGMII PHY when you do not want use 125Mhz
+ * from PHY
+ *-----------------------------------------------------
+ * src | BIT(17) | BIT(16) |
+ *-----------------------------------------------------
+ * MII | n/a | n/a |
+ *-----------------------------------------------------
+ * GMII | n/a | st,eth_clk_sel |
+ *-----------------------------------------------------
+ * RGMII | n/a | st,eth_clk_sel |
+ *-----------------------------------------------------
+ * RMII | st,eth_ref_clk_sel | n/a |
+ *-----------------------------------------------------
+ *
+ */
+
struct stm32_dwmac {
struct clk *clk_tx;
struct clk *clk_rx;
struct clk *clk_eth_ck;
struct clk *clk_ethstp;
struct clk *syscfg_clk;
- bool int_phyclk; /* Clock from RCC to drive PHY */
+ int eth_clk_sel_reg;
+ int eth_ref_clk_sel_reg;
int irq_pwr_wakeup;
- u32 mode_reg; /* MAC glue-logic mode register */
+ u32 mode_reg; /* MAC glue-logic mode register */
struct regmap *regmap;
u32 speed;
const struct stm32_ops *ops;
@@ -103,7 +157,7 @@ static int stm32mp1_clk_prepare(struct stm32_dwmac *dwmac, bool prepare)
if (ret)
return ret;
- if (dwmac->int_phyclk) {
+ if (dwmac->clk_eth_ck) {
ret = clk_prepare_enable(dwmac->clk_eth_ck);
if (ret) {
clk_disable_unprepare(dwmac->syscfg_clk);
@@ -112,7 +166,7 @@ static int stm32mp1_clk_prepare(struct stm32_dwmac *dwmac, bool prepare)
}
} else {
clk_disable_unprepare(dwmac->syscfg_clk);
- if (dwmac->int_phyclk)
+ if (dwmac->clk_eth_ck)
clk_disable_unprepare(dwmac->clk_eth_ck);
}
return ret;
@@ -122,7 +176,7 @@ static int stm32mp1_set_mode(struct plat_stmmacenet_data *plat_dat)
{
struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
u32 reg = dwmac->mode_reg;
- int val;
+ int val, ret;
switch (plat_dat->interface) {
case PHY_INTERFACE_MODE_MII:
@@ -131,19 +185,22 @@ static int stm32mp1_set_mode(struct plat_stmmacenet_data *plat_dat)
break;
case PHY_INTERFACE_MODE_GMII:
val = SYSCFG_PMCR_ETH_SEL_GMII;
- if (dwmac->int_phyclk)
+ if (dwmac->eth_clk_sel_reg)
val |= SYSCFG_PMCR_ETH_CLK_SEL;
pr_debug("SYSCFG init : PHY_INTERFACE_MODE_GMII\n");
break;
case PHY_INTERFACE_MODE_RMII:
val = SYSCFG_PMCR_ETH_SEL_RMII;
- if (dwmac->int_phyclk)
+ if (dwmac->eth_ref_clk_sel_reg)
val |= SYSCFG_PMCR_ETH_REF_CLK_SEL;
pr_debug("SYSCFG init : PHY_INTERFACE_MODE_RMII\n");
break;
case PHY_INTERFACE_MODE_RGMII:
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ case PHY_INTERFACE_MODE_RGMII_TXID:
val = SYSCFG_PMCR_ETH_SEL_RGMII;
- if (dwmac->int_phyclk)
+ if (dwmac->eth_clk_sel_reg)
val |= SYSCFG_PMCR_ETH_CLK_SEL;
pr_debug("SYSCFG init : PHY_INTERFACE_MODE_RGMII\n");
break;
@@ -154,6 +211,11 @@ static int stm32mp1_set_mode(struct plat_stmmacenet_data *plat_dat)
return -EINVAL;
}
+ /* Need to update PMCCLRR (clear register) */
+ ret = regmap_write(dwmac->regmap, reg + SYSCFG_PMCCLRR_OFFSET,
+ dwmac->ops->syscfg_eth_mask);
+
+ /* Update PMCSETR (set register) */
return regmap_update_bits(dwmac->regmap, reg,
dwmac->ops->syscfg_eth_mask, val);
}
@@ -237,22 +299,25 @@ static int stm32mp1_parse_data(struct stm32_dwmac *dwmac,
struct device_node *np = dev->of_node;
int err = 0;
- dwmac->int_phyclk = of_property_read_bool(np, "st,int-phyclk");
+ /* Gigabit Ethernet 125MHz clock selection. */
+ dwmac->eth_clk_sel_reg = of_property_read_bool(np, "st,eth_clk_sel");
- /* Check if internal clk from RCC selected */
- if (dwmac->int_phyclk) {
- /* Get ETH_CLK clocks */
- dwmac->clk_eth_ck = devm_clk_get(dev, "eth-ck");
- if (IS_ERR(dwmac->clk_eth_ck)) {
- dev_err(dev, "No ETH CK clock provided...\n");
- return PTR_ERR(dwmac->clk_eth_ck);
- }
+ /* Ethernet 50Mhz RMII clock selection */
+ dwmac->eth_ref_clk_sel_reg =
+ of_property_read_bool(np, "st,eth_ref_clk_sel");
+
+ /* Get ETH_CLK clocks */
+ dwmac->clk_eth_ck = devm_clk_get(dev, "eth-ck");
+ if (IS_ERR(dwmac->clk_eth_ck)) {
+ dev_warn(dev, "No phy clock provided...\n");
+ dwmac->clk_eth_ck = NULL;
}
/* Clock used for low power mode */
dwmac->clk_ethstp = devm_clk_get(dev, "ethstp");
if (IS_ERR(dwmac->clk_ethstp)) {
- dev_err(dev, "No ETH peripheral clock provided for CStop mode ...\n");
+ dev_err(dev,
+ "No ETH peripheral clock provided for CStop mode ...\n");
return PTR_ERR(dwmac->clk_ethstp);
}
@@ -268,7 +333,7 @@ static int stm32mp1_parse_data(struct stm32_dwmac *dwmac,
*/
dwmac->irq_pwr_wakeup = platform_get_irq_byname(pdev,
"stm32_pwr_wakeup");
- if (!dwmac->int_phyclk && dwmac->irq_pwr_wakeup >= 0) {
+ if (!dwmac->clk_eth_ck && dwmac->irq_pwr_wakeup >= 0) {
err = device_init_wakeup(&pdev->dev, true);
if (err) {
dev_err(&pdev->dev, "Failed to init wake up irq\n");
@@ -370,7 +435,7 @@ static int stm32mp1_suspend(struct stm32_dwmac *dwmac)
clk_disable_unprepare(dwmac->clk_tx);
clk_disable_unprepare(dwmac->syscfg_clk);
- if (dwmac->int_phyclk)
+ if (dwmac->clk_eth_ck)
clk_disable_unprepare(dwmac->clk_eth_ck);
return ret;
--
2.7.4